BEFORE FIRST USE Before first use or when the appliance has not been used for an extended period of time, run a cleansing brew at least once with water only: 1. Fill the Water Tank to the MAX Fill Line. • Water Tank can be filled while in the unit or detached. 2. Insert Hot Water Insert into the Insert Chamber. • See Assembly for the Hot Water Insert on page 14. 3. Set full-sized Carafe on the Drip Tray Base. 4. Press “Power” to preheat. 5. Select “tea/hot water” for the coffee selection. 6.
CHARCOAL FILTER HOLDER ASSEMBLY For additional water purification, use the supplied (optional) Charcoal Filter Holder with Filter. Note: The coffee maker will still operate without Charcoal Filter Holder installed. 1. Flush Filter by running under cold tap water for 1-3 minutes before initial use. After flushing, allow the Filter to drain completely. 2. Carefully place Filter into compartment and snap to close. • Flat side (base) of cartridge must face down inside Filter Holder compartment. 3.
WATER COMPARTMENT ASSEMBLY Fill water directly in the Water Tank when attached, or remove first. To fill directly in the Water Tank: 1. Lift the Water Tank Lid up and pour in water to appropriate fill line. 2. Close the Water Tank Lid. • Coffee maker will not operate when tank is removed or when there is no water. MAX Fill Line Full Carafe To fill Water Tank when removed: 1. Lift Water Tank Lid and place to the side. Half Carafe 12oz Cup 8oz Cup 2. Lift Water Tank up to remove from the side. 3.
ASSEMBLY FOR INSERTS With your NuWave BruHubTM 3-in-1 Coffee Maker, you can choose from three different inserts to customize your coffee-drinking experience and preference. Single Serve Insert 1. Line up dots with each other and place Single Serve Insert into the Insert Chamber. 2. Place pod into Single Serve Insert. 3. Close down Single Serve Lid. • Make sure lid is fully closed. • Use Mug Tray on Drip Tray Base and Screen for smaller cups and mugs. • Use “8” and “12” sizes for Single Serve Insert.
ASSEMBLY FOR INSERTS (CONT.) Hot Water Insert Line up dots with each other and place Hot Water Insert directly down into Insert Chamber. Close lid. • Use Mug Tray on Tray Base for smaller cups and mugs. • Use “8”, “12”, “half carafe”, and “carafe” for Hot Water Insert. CARAFE ASSEMBLY 1. Place Carafe Lid on top of Carafe Base. 14 Owner’s Manual Downloaded from www.Manualslib.com manuals search engine 2. Line up dots by turning clockwise to lock into place.
FUNCTIONS FOR THE NUWAVE BRUHUBTM Power Button: 1. Press “Power” button once to turn the unit on. There will be a blue light next to “Power” button to indicate it is on. • When you press the “Power” button, there will be a red light next to “preheating”. Once it has preheated, the red light will turn off, indicating the water is ready to brew. Once it has preheated, press “brew”. • Unit will beep when the brew is complete. 2. Press “Power” again to turn the unit off.
FUNCTIONS FOR THE NUWAVE BRUHUBTM (CONT.) Coffee/Hot Water selection function: This lets you select your favorite beverage with the push of a button. 1. Default is set for “regular”. 2. Press the “beverage selection” button once and the blue light next to “bold” will be lit. 3. Press the “beverage selection” button again to change the selection to “iced”, “hot water”, or back to “regular”. • When “iced” is selected, half of the amount will be dispersed.
INSERT & BEVERAGE SELECTION CHARTS INSERT SELECTION: 8oz 12oz Single Serve Insert x x * Custom Brew Insert x Hot Water Insert x Inserts ½ Carafe 21oz Full Carafe 42oz x x x x x x * You must use carafe with this insert. BEVERAGE SELECTION: Scooper holds 8 grams of coffee grounds when leveled. Adjust the strength of coffee by using more or less grounds.
CLEANING AND MAINTENANCE To clean Hot Water Insert, pull up Hot Water Cap to separate and clean insides of both parts. • Hot Water Insert and Hot Water Cap are dishwasher safe, top rack only. • Hot Water Cap snaps back on after it’s cleaned. For Custom Brew Insert, lift up Custom Brew Lid to clean inside. Remove Custom Brew Insert Cap. • Press in the tabs to remove Custom Brew Cap from Custom Brew Lid. • Custom Brew Cap is dishwasher safe, top rack only. • Remove Filter Basket to clean individually.
CLEANING AND MAINTENANCE (CONT.) Cleaning needle under Lid: The needle is located under the Lid. To clean needle, use a thin piece of metal or metal wire brush to free the part and area with any blockage. The Mug Tray is detachable and can be removed and cleaned. The two layers can be separated. • The Mug Tray is dishwasher safe, top rack only. The Drip Tray Base is detachable and can be removed and cleaned. • The base is dishwasher safe, top rack only.
CLEANING AND MAINTENANCE (CONT.) Cleaning Carafe: To clean the Carafe, use warm soapy water and rinse thoroughly. Use a soft foam brush with a long handle to reach the bottom. • The Carafe Lid is removable and is dishwasher safe, top rack only. External Cleaning To clean the exterior of your coffee maker, wipe with a damp, soapy, soft cloth. Descaling Scale is a buildup that can occur over time after many uses of your appliance.
