User's Manual
Table Of Contents
- Safety Precautions
- Regulatory Compliance FCC
- Manual Overview
- Introduction
- Technical Specifications
- Physical Interfaces
- Enabler II-G Mounting Reference
- Pin Orientation Reference
- Connectors
- I/O Signal Connector on the Enfora Enabler II-G Module
- Antenna
- Control Connector Signal Descriptions and Functions
- Input Power
- Ring Indicate
- Radio Power/Reset
- Serial Interface (9 Pin I/F) (See table in section 6.5.1 I/O Connector Pin Assignments)
- General Purpose Input/Output Interface (GPIO)
- Analog-To-Digital Input
- Digital-To-Analog Output
- Handset Microphone Input
- Handset Speaker Output
- Headset Microphone Input
- Headset Speaker Output
- Audio Design Note
- Subscriber Identity Module (SIM) Carrier
- Modes of Operation
- SIM Operation
- Software Interface
- Setup and Initialization
- General Setup
- HyperTerminal Configuration for Enabler II-G
- Initialization (AT Command Interface)
- Initial Response to the AT Command
- Sending an Initialization String to the Enfora Enabler II-G Module
- Setting Up the Communication Mode for the Enfora Enabler II-G Module
- Querying the Status of the Enfora Enabler II-G Module
- Setting Module Reporting Parameters for GSM and GPRS
- GSM/SMS Examples
- GPRS Packet Examples
- General Setup
- Integration and Testing
- APPENDIX A - Warranty Repair and Return Policy
- APPENDIX B - Regulations and Compliance
- GCF Approval (Formerly FTA)
- Electromagnetic Compatibility (EMC) and Safety Requirements
- EMC/Safety Requirements for the USA
- Human Exposure Compliance Statement
- Compliance with FCC Regulations
- Unintentional Radiators, Part 15
- Intentional Radiators, Part 24
- Instructions to the Original Equipment Manufacturer (OEM)
- Nationally Recognized Testing Laboratory (NRTL) Approval
- EMC/Safety Requirements for the Countries of the European Union (EU)
- EMC/Safety Requirements for Other Countries
- APPENDIX C - Glossary and Acronyms
- APPENDIX D – Tables And Figures
- APPENDIX E - Contacting Enfora
Integration Guide
Version 1.07
GSM0100PB001 Page 7 1.07 - 1/9/04
3.0 Manual Overview
This document describes the hardware interface of the Enabler II-G GSM/GPRS OEM Modem. The
purpose of this document is to define the electrical, mechanical and software interfaces while providing
detailed technical information in order to streamline the process of hardware and system integration.
3.1 Revision History
Date Rev Author Description
7/16/03 Draft Matt Glover Initial Draft.
8/27/03 1.00 Matt Glover
• Modified values in 5.3 Operating Power
• Modified drawings in 6.1 Physical Layout
• Modified drawing in 6.2 Enabler II-G Mounting Reference
• Modified pins 35, 36, 46, and 56 in 6.5.1 I/O Connector Pin
Assignments
• Added section 6.7.6 Analog-To-Digital Input
• Added section 6.7.7 Digital-To-Analog Output
• Added section 6.7.12 Audio Design Note
• Added Warranty Information
9/4/03 1.01 Matt Glover
• Modified section 6.7.12 Audio Design Note
9/18/03 1.02 Matt Glover
• Revised serial pin numbers in 6.5.1 I/O Connector Pin Assignments
• Changed Enabler II-G description for pin #47 in 6.5.1 I/O Connector
Pin Assignments
• Modified section 6.7.12 Audio Design Note
• Modified descriptions for pins #20, #26, #29 #31, #36, and # 37 in
6.5.1 I/O Connector Pin Assignments
9/22/03 1.03 Matt Glover
• Removed 5V tolerant reference in 4.2 Key Features of the
GSM/GPRS OEM Module and 11.0
Integration and Testing
11/13/03 1.04 Matt Glover
• Added support for GSM0108 quad-band modem.
12/2/03 1.05 Matt Glover
• Added SIM interface details to pinout chart.
12/11/03 1.06 Matt Glover
• Revised Figure 3 Enabler II-G Package Dimensions (without
integrated SIM carrier) drawing
1/8/04 1.07 Matt Glover
• Revised FCC Compliance Statament
• Modified description for pin #24in 6.5.1 I/O Connector Pin
Assignments