Manufacturer: NOKTA MUHENDISLIK INS. ELEK. PLAS. GIDA VE REKLAM SAN. TIC. LTD. STI.
READ CAREFULLY BEFORE OPERATION OF THE DEVICE LEGAL DISCLAIMERS Comply with applicable laws and regulations governing use of metal detectors while using this detector. Do not use the detector without authorization in protected or archaeological sites. Do not use this detector around unexploded ordnance or in restricted military zones without authorization. Notify appropriate authorities with details of any historical or culturally significant artefacts you find.
INTRODUCTION TO THE DEVICE The PulseDive can be purchased in 2 models: Scuba Detector & Pointer 2-in-1 Set and as a stand-alone Pinpointer only. Both models have the same functions and operate the same way. The only difference between them is the scuba coil and some accessories included in the 2-in-1 set. If you bought the stand-alone pinpointer, please disregard the instructions about the scuba coil in the assembly section. You can purchase the scuba coil separately to add that functionality at anytime.
ASSEMBLY The PulseDive comes with the scuba coil attached. If you want to use the pinpointer coil, please follow the steps in the pictures. If you want to re-attach the scuba coil, repeat the steps in reverse order. IMPORTANT! When changing coils, align the plastic tab on the control unit with the opposing groove on the coil and twist clockwise to secure. 1) To detach the scuba coil, turn it counter clockwise. 2) Pull the scuba coil out of the control unit.
ASSEMBLY 3) Hold the pinpointer coil so that the threads are properly aligned. 4) Insert the pinpointer coil into the control unit and push. 3 4 5) To attach the pinpointer coil, insert the hard-shell case over the pointer coil and push half-way forward. 6) Then, twist the coil clockwise to tighten. Lastly, push the hard-shell case all the way so it clicks into place. 5 6 IMPORTANT! The pinpointer coil is designed to fit very tightly to provide a waterproof seal.
ASSEMBLY WARNING: If you change the coil while the device is on, you must retune the device by pressing the on-off / retune button once. In order to not lose the PulseDive while using it underwater or on land, we recommend you to attach the security lanyard as shown in the below picture. 7) Attach one end (a) of the security lanyard to the hole located at the back of the control unit and the other end with the snap hook (b) to your belt or wrist band.
BATTERY INFORMATION The PulseDive has an internal 1650mAh Lithium Polymer battery. Charge the PulseDive before initial use. Charging will take approximately 2 hours. Charging You can charge the device with a USB charger, a powerbank, on a PC or in your car using the included charging cable. * The charging time may be longer for USB chargers rated less than 1 Amp or older type of PCs. While charging, the red LED will light up solid. When the battery is full, the green and red LEDs will light up together.
OPERATION OF THE DEVICE During the operation of the PulseDive, the Green LED blinks once when you press any button. It lights up solid when the buttons are pressed down and held. POWER ON-OFF Press the on-off button once to turn the device on. A beep will be heard and the LEDs will light up according to the battery life status. To turn the device off, press and hold the on-off button. Double beeps will be heard, regardless of the mode used, and both LEDs will light up simultaneously.
OPERATION OF THE DEVICE number of beeps and/or vibrations depending on the mode used. For example level 4 is indicated by 4 beeps and/or vibrations. At maximum sensitivity -level 5- the device emits a long beep and/or vibration. If the red LED is active, it lights up solid. Inside highly mineralized holes, the device may produce false signals. In such a case, reduce the sensitivity. LED FLASHLIGHT To activate flashlight, press the adjustment button (A) once while the device is on.
OPERATION OF THE DEVICE NOTE: The wireless headphones will not work if the device is switched to dive mode while it is connected the wireless headphones. The wireless headphones will connect automatically once the device exits the dive mode. IMPORTANT! The PulseDive comes with 2 battery compartment covers.
TECHNICAL SPECIFICATIONS Operating Principle Operating Frequency Frequency Shift Waterproofness Built-in Wireless Module Detection Modes Sensitivity Length Weight Battery Charging Time Warranty : Pulse Induction : 3kHz : Yes : IP68 - Up to 60m. (200ft.) : Yes : Audio / Vibration / Audio + Vibration / LED : 5 levels adjustable : Scuba Detector: 39cm. (15.3'') : Pinpointer: 28cm. (11'') : Scuba Detector: 419gr. (14.8oz) including the coil cover : Pinpointer: 286 gr.