User's Manual
Table Of Contents
- Chapter 4: Acceptance Test Procedures
- Automated Acceptance Test Procedure
- Acceptance Tests - Test Set-up
- Abbreviated (All-inclusive) Acceptance Tests
- Individual Acceptance Tests
- TX Spectral Purity Transmit Mask Acceptance Test
- TX Waveform Quality (Rho) Acceptance Test
- TX Pilot Time Offset Acceptance Test
- TX Code Domain Power/Noise Floor Acceptance Test
- RX FER Acceptance Test
- Generating an ATP Report
- Updating Calibration Data Files
- Chapter 5: Prepare to Leave the Site
- Chapter 6: Troubleshooting
- Basic Troubleshooting: Overview
- Troubleshooting: Installation
- Cannot Log into Cell-Site
- Force LAN A Active (LMF Connection at I/O Panel LAN Connector)
- Force LAN A Active (LMF Connection at Service Shelf LAN Connector)
- Set the GLI IP Address
- Cannot Communicate with Power Meter
- Cannot Communicate with Communications System Analyzer
- Cannot Communicate with Signal Generator
- Troubleshooting: Download
- Troubleshooting: Calibration
- Basic Troubleshooting: RF Path Fault Isolation
- Troubleshooting: Transmit ATP
- Troubleshooting: Receive ATP
- Troubleshooting: CSM Checklist
- Troubleshooting: SCCP Backplane
- Troubleshooting: RFDS
- Module Front Panel LED Indicators and Connectors
- Troubleshooting: Span Control Link
- Appendix A: Data Sheets
- Appendix B: PN Offset/I & Q Offset Register Programming Information
- Appendix C: FRU Optimization / ATP Test Matrix
- Appendix D: BBX Gain Set Point vs. BTS Output
- Appendix E: CDMA Operating Frequency Programming Information
- Appendix F: Test Equipment Preparation
- Test Equipment Preparation
- Verifying and Setting GPIB Addresses
- Agilent E4406A Transmitter Tester GPIB Address
- Agilent E4432B Signal Generator GPIB Address
- Advantest R3267 Spectrum Analyzer GPIB Address
- Advantest R3562 Signal Generator GPIB Address
- Agilent 8935 Series E6380 (formerly HP 8935) Test Set GPIB Address
- Hewlett Packard HP 8921A and HP83236A/B GPIB Address
- Advantest R3465 Communications Test Set GPIB Address
- Motorola CyberTest GPIB Address
- HP 437 Power Meter GPIB Address
- Gigatronics 8541C Power Meter GPIB Address
- RS232 GPIB Interface Adapter
- Test Equipment Inter-Unit Connection, Testing, and Control
- Inter-Unit Connection, Testing, and Control Settings
- HP 8921A with PCS Interface Test Equipment Connections
- HP 8921A with PCS Interface System Connectivity Test
- Pretest Set-up for HP 8921A
- Pretest Set-up for Agilent 8935
- Advantest R3465 Connection
- R3465 GPIB Clock Set-up
- Pretest Set-up for Advantest R3465
- Agilent 8932/E4432B Test Equipment Interconnection
- Agilent E4406A/E4432B Test Equipment Interconnection
- Advantest R3267/R3562 Test Equipment Interconnection
- Equipment Calibration
- Manual Cable Calibration
- Appendix G: Downloading ROM Code
- Appendix H: In-Service Calibration
- Appendix I: Packet Backhaul Configuration
- BTS Router Initial Configuration
- Terminal Setup
- Downloading Minimum Canned BTS Router Configuration Files
- Verifying IOS Canned Version of the CF Memory Card
- Replacing Installed BTS Router CF Memory Card IOS Version
- Background
- Equipment and Software Required for Verification Methods
- Required Publications
- Method 1: Replacement of Installed Router CF Card IOS Data
- Method 2: Using a CF Memory Card Reader for Replacement of Installed IOS Version and Changing File Sequence ...
- Change CF Memory Card File Sequence to Place IOS File First on the Card
- Verify and Upgrade ROMMON Version
- Recovery from BTS Router Boot to ROMMON
- Entering or Changing Router FE Interface IP Address
- Preparation for Site Turn-over
- Index
In–Service Calibration – continued
FEB 2005 1X SC 4812T Lite BTS Optimization/ATP H-27
PRELIMINARY
Table H-6: In–Service Calibration Procedure
n ActionStep
7 If it was not previously done, have the CBSC Operator put the Redundant BBX OOS_MANUAL.
! CAUTION
Be sure to download OOS devices only.
– Loading in–service devices takes them OUT OF SERVICE and can result in dropped calls.
The Code File Version Numbers must match the Version Numbers on the other cards in the frame.
If the numbers do not match, the site may go OUT OF SERVICE.
NOTE
Be sure to include the Redundant BBX in Steps 8, 9, and 10.
8 Download code and data to the target devices:
8a In the LMF Window Menu Bar, click Tools > Update NextLoad > CDMA to set the Code
Version that will be downloaded.
8b Check the appropriate Code Version in the Pop–up Window and click the Save Button to close.
8c Select the target BBX(s) on the SCCP Cage picture.
8d In the BTS Menu Bar, click Device > Download > Code/Data to start downloading code and data.
! CAUTION
Perform the All Cal/Audit Procedure on OOS devices only.
9 Run the All Cal/Audit Procedure:
9a Select the target BBX(s) on the SCCP Cage picture.
9b In the BTS Menu Bar, click Tests > All Cal/Audit... from the Menu Bar in the Main Window.
9c Select the target carrier and confirm the Channel Number in the Pop–up Window.
9d Leave the Verify BLO Check Box checked.
9e Ensure that the Test Pattern Box shows Pilot.
9f Click the OK Button to start Calibration.
9g Follow the on–screen instructions, except, do not connect to the BTS Antenna Port.
9h Connect to the DRDC or TRDC BTS CPL Port associated with the on–screen prompted Antenna
Port.
10 Save the result, and download the BLO Data to the target BBX(s):
– Click the Save Result Button on the result screen.
–– The window closes automatically.
11 Logout from the BTS and close the LMF Session:
11a In the BTS Menu Bar, click Select > Logout to close the BTS Connection.
11b Close the LMF Application Program by selecting File > Exit from the Window Menu Bar.
table continued on next page
H