Caution : You must read this before you proceed Armless Chair Label Picture Description QTY A Backrest with Leg 1 B Left Panel with Leg 1 C Right Panel with Leg 1 Noble House Home Furnishings LLC Page 1 OF 6
D Seat 1 E Back Cushion 1 F Seat Cushion 1 Description QTY ① Bolt Cap 11 ② Bolt (M6*45mm) 11 ③ Washer 11 ④ Spring Washer (Ø16*2mm) 11 ⑤ Allen Key 1 Label Picture Before Beginning Assembly: Noble House Home Furnishings LLC Page 2 OF 6
Over View Backrest with Leg(A) Back Cushion(E) Seat Cushion(F) Seat(D) Left Panel with Leg (B) Right Panel with Leg(C) This Armless Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Armless Chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 Attach the Seat(D) to Right Panel with Leg(C) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤). Do not fully tighten the bolts. Step 3 Place the Left Panel with Leg(B) facedown on the clean and soft suface. With the help of your adult partner, place the Backrest with Leg(A) against Left Panel with Leg(B). Attach the Left Panel with Leg(B) to Seat(D) and Backrest with Leg(A) using Bolts(②), Spring Washers(④) and Washers(③) with Alley Key(⑤).
Step 4 Turn the Armless Chair face down on the clean, non-marring surface. Use the Bolt Cap(①) to cover all Bolts. Step 5 Place the Armless Chair on a level surface to check the wobbles. If the Armless Chair wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 6 Place the Seat Cushion(F) and Back Cushion(E) on the Armless Chair. Your Armless Chair is ready for use. This Armless Chair can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 6 OF 6
Caution : You must read this before you proceed Left Armchair Label Picture Description QTY G Backrest with Leg 1 H Left Armrest with Leg 1 Noble House Home Furnishings LLC Page 1 OF 7
I Right Panel with Leg 1 J Seat 1 E Back Cushion 1 F Seat Cushion 1 Description QTY ① Bolt Cap 11 ② Bolt (M6*45mm) 11 ③ Washer 11 ④ Spring Washer (Ø16*2mm) 11 ⑤ Allen Key 1 Label Picture Noble House Home Furnishings LLC Page 2 OF 7
Before Beginning Assembly: Overview Back Cushion (E) Left Armrest with Leg(H) Backrest with Leg (G) Seat Cushion (F) Seat (J) Right Panel with Leg (I) This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Dowel Place the Left Armrest with Leg(H) facedown on a clean, non-marring surface. Place the Backrest with Leg(G) on the Armrest with Leg(H) being sure to insert dowel on Armrest with Leg(H) into mounting position on Backrest with Leg(G). Attach Backrest with Leg(G) to Left Armrest with Leg(H) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Do not fully tighten the bolts.
Step 3 Place the Right Panel with Leg(I) facedown on a clean, non-marring surface. With the help of your adult partner, place Backrest against Right Panel with Leg(I). Attach the Right Panel with Leg(I) to Backrest with Leg(G) and Seat(J) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as pictured above. Tighten all Bolts at all joints completely at this stage. Step 4 Turn the Armchair face down. Use the Bolt Caps(①) to cover all Bolts.
Step 5 Place the Armchair on a level surface to check the wobbles. If the Armchair wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 6 Place the Seat Cushion(F) and Back Cushion(E) on the Armchair. Your Armchair is ready for use. This Armchair can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 7 OF 7
Caution : You must read this before you proceed Right Armchair Label Picture Description QTY K Backrest with Leg 1 L Right Armrest with Leg 1 Noble House Home Furnishings LLC Page 1 OF 7
M Left Panel with Leg 1 N Seat 1 E Back Cushion 1 F Seat Cushion 1 Description QTY ① Bolt Cap 11 ② Bolt (M6*45mm) 11 ③ Washer 11 ④ Spring Washer (Ø16*2mm) 11 ⑤ Allen Key 1 Label Picture Noble House Home Furnishings LLC Page 2 OF 7
Before Beginning Assembly: Overview Back Cushion (E) Right Armrest with Leg (L) Backrest with Leg(K) Seat Cushion (F) Seat (N) Left Panel with Leg (M) This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Dowel Place the Right Armrest with Leg(L) facedown on a clean, non-marring surface. Place the Backrest with Leg(K) on the Armrest with Leg(L) being sure to insert dowel on Armrest with Leg(L) into mounting position on Backrest with Leg(K). Attach Backrest with Leg(K) to Left Armrest with Leg(L) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Do not fully tighten the bolts.
Step 3 Place the Right Panel with Leg(M) facedown on a clean, non-marring surface. With the help of your adult partner, place Backrest against Right Panel with Leg(M). Attach the Right Panel with Leg(M) to Backrest with Leg(K) and Seat(N) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as pictured above. Tighten all Bolts at all joints completely at this stage. Step 4 Turn the Armchair face down. Use the Bolt Caps(①) to cover all Bolts.
Step 5 Place the Armchair on a level surface to check the wobbles. If the Armchair wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 6 Place the Seat Cushion(F) and Back Cushion(E) on the Armchair. Your Armchair is ready for use. This Armchair can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 7 OF 7
Caution : You must read this before you proceed Ottoman Label Picture Description QTY O Top Panel 1 P Front/Back Panel 2 Q Side Panel with Legs 2 Noble House Home Furnishings LLC Page 1 OF 6
U Seat Cushion 1 Description QTY ① Bolt Cap 13 ② Bolt (M6*45mm) 13 ③ Washer 13 ④ Spring Washer (Ø16*2mm) 13 ⑤ Allen Key 1 Label Picture Before Beginning Assembly: Noble House Home Furnishings LLC Page 2 OF 6
Overview Seat Cushion(U) Top Panel(O) Front Panel(P) Side Panel with Leg(Q) This Ottoman has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Ottoman parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all parts on a clean, non-marring surface.
Step 2 Place the Top Panel(O) facedown on a clean and soft surface. With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(O) as shown above. Attach the Top Panel(O) to the Front and Back Panels(P) and Side Panels with Legs(Q) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Tighten all Bolts at all joints completely at this stage. Step 3 Use the Bolt Cap(①) to cover all Bolts.
Step 4 Place the Ottoman on a level surface to check the wobbles. If the Ottoman wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 5 Place the Seat Cushion(U) on the ottoman. Your Ottoman is ready for use. This Ottoman can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 6 OF 6
Caution : You must read this before you proceed Table Label Picture Description QTY R Top Panel 1 S Front/Back Panel 2 T Side Panel with Legs 2 Noble House Home Furnishings LLC Page 1 OF 6
Label Picture Description QTY ① Bolt Cap 13 ② Bolt (M6*45mm) 13 ③ Washer 13 ④ Spring Washer (Ø16*2mm) 13 ⑤ Allen Key 1 Before Beginning Assembly: Noble House Home Furnishings LLC Page 2 OF 6
Overview Top Panel(R) Side Panel with Legs(T) Front Panel(S) This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all parts on a clean, non-marring surface.
Step 2 Place the Top Panel(R) facedown on a clean and soft surface. With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(R) as shown above. Attach the Top Panel(R) to the Front and Back Panels(S) and Side Panels with Legs(T) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Tighten all Bolts at all joints completely at this stage. Step 3 Use the Bolt Cap(①) to cover all Bolts.
Step 4 Place the Table on a level surface to check the wobbles. If the Table wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 5 Your Table is ready for use. This Table can only be used on a flat, level surface.
Questions & Answers about Proposition 65 • What is Proposition 65? Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. These chemicals can be in the products that Californians purchase, in their homes or workplaces, or that are released into the environment.
Caution : You must read this before you proceed Single Sofa Label Picture Description QTY A Sofa - Backrest 1 B Right Armrest 1 C Left Armrest 1 D Sofa Seat 1 Page 1 OF 6
Label Picture Description QTY F Plastic Cap 13 G Bolt M6*40mm 13 H Washer 13 I Spring Washer Ø16*2mm 13 J Allen Key 1 Before Beginning Assembly: Page 2 OF 6
Overview Sofa - Backrest(A) Right Armrest(B) Sofa Seat(D) Left Armrest(C) This Single Sofa has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Single Sofa parts, the above picture is to help you put the various parts into perspective. Please read through the instructions herebelow to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all the parts onto a clean and soft surface. Unpack all packages of hardware.
Step 2 Place the Seat (D) between the Right Armrest(B) and Backrest(A). Attach the Seat(D) to the Right Armrest(B) with hardware as picture 3 and 4 shows. Use an Allen Key(L) to partially tighten these. Do not fully tighten the bolts. Step 3 Place the Left Armrest (C ) against the Backrest(A) and Seat(D). Make the metal rod on the Backrest(A) insert into the MOUNTING POSITIONs of the Left Armrest(C ) as picture 5 shows. Attach the Left Armrest(C ) to Backrest(A) with hardware as picture 6 shows.
Step 4 Tighten all bolts completely. Put the Plastic Cap(F) to cover the bolt heads, adjust the Leveler to ensure good stability. Step 5 It is ready for use. This Single Sofa can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Ottoman Label Picture Description QTY O Top Panel 1 P Front/Back Panel 2 Q Side Panel 2 Page 1 OF 6
U Seat Cushion 1 Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 13 ③ Washer 13 ④ Spring Washer (Ø16*2mm) 13 ⑤ Allen Key 1 Label Picture Before Beginning Assembly: Page 2 OF 6
Overview Seat Cushion(F) Top Panel(O) Front Panel(P) Side Panel(Q) This Ottoman has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Ottoman parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all parts on a clean, non-marring surface.
Step 2 Place the Top Panel(O) facedown on a clean and soft surface. With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(O) as shown above. Attach the Top Panel(O) to the Front and Back Panels(P) and Side Panels(Q) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Tighten all Bolts at all joints completely at this stage. Step 3 Use the Bolt Cap(①) to cover all Bolts.
Step 4 Place the Ottoman on a level surface to check the wobbles. If the Ottoman wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 5 Place the Seat Cushion(U) on the ottoman. Your Ottoman is ready for use. This Ottoman can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Table Label Picture Description QTY V Top Panel 1 W Front/Back Panel 2 X Side Panel 2 Page 1 OF 6
Label Picture Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 13 ③ Washer 13 ④ Spring Washer (Ø16*2mm) 13 ⑤ Allen Key 1 Before Beginning Assembly: Page 2 OF 6
Overview This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all parts on a clean, non-marring surface.
Step 2 Place the Top Panel(V) facedown on a clean and soft surface. With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(R) as shown above. Attach the Top Panel(R) to the Front and Back Panels(S) and Side Panels(T) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Tighten all Bolts at all joints completely at this stage. Step 3 Use the Bolt Cap(①) to cover all Bolts.
Step 4 Place the Table on a level surface to check the wobbles. If the Table wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 5 Your Table is ready for use. This Table can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
