Assembly Instructions Caution: You must read this before you proceed Please look in the magic tape pouch for hardware packs and legs SOFA Noble House Home Furnishings LLC Page 1 OF 11
Part List Label Picture Description QTY A Backrest ( with preattached Tapered Connectors ) 1 B Left Armrest ( with preattached Tapered Connectors ) 1 C Right Armrest ( with preattached Tapered Connectors ) 1 D Seat Base ( with preattached Handle Straps ( at the Top Side ) and preattached Metal Brackets ( at the Bottom Side ) 1 E Front Rail (as shown here from the inside - with Wooden Support Bar ) 1 F Seat Cushion 3 G Leg 4 Noble House Home Furnishings LLC Page 2 OF 11
Hardware List Label Picture Description QTY ① Plastic Washer 7 ② Allen Wrench 1 Assembly Preparation Before Beginning Assembly: *3 Noble House Home Furnishings LLC *4 *7 *1 Page 3 OF 11
Assembly Steps OVERVIEW Left Armrest(B) Backrest(A) Right Armrest(C) Front Rail(E) Seat Cushion(F) Leg(G) FRONT FACING This Sofa has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Sofa parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Right Armrest(C) Backrest(A) Left Armrest(B) Keep the Backrest(A) and the back of the Left Armrest(B), Right Armrest(C) flat. Open the carton and place all the parts on a clean, non-marring surface. Caution : 1. ) You may need to use one hand to depress the foam cushion in the Backrest panel to ease the installation into the armrests. 2. ) Be careful to NOT get your fingers get caught or pinched at the Tapered Connectors area. 3.
Next, move and stand into seat box area of the sofa. As pictured above, in the inner face of Backrest(A),both Armest and towards the base of the arm, you will see eight( 8 ) pcs of pre-attached botls. Using the Allen Wrench(②), loosen these bolts to about half an inch. Step 3 Right Armrest(C) Left Armrest(B) Front Rail(E) Note : Whilst attaching this Front Rail(E), the sliding action needs to be synchronised with your partner.
Step 4 Backrest(A) Seat Base(D) Front Rail with Wooden Support Bar(E) Together with your partner, lift the Strap Handles, at the sides, found on the Top face of the Seat Base(D). Gently, place the Seat Base(D) into the Sofa so as to allow for : 1. ) 2( two ) Metal Brackets to hook into the Bolts at the base of the Backrest ; 2. ) 2( two ) Metal Brackets to hook into the Bolts in both bases of the Armrests ; 3. ) The front of the Seat Base(D) to rests onto the Wooden Support Bar in the Front Rail(E).
Step 5 Left Armrest(B) Right Armrest(C) Step 5.1 ② ② Right Armrest(C) Left Armrest(B) Step 5.2 ② Here in Step5 - there are 2 sub-steps. First, tilt and lay the Sofa on its Backrest. In a sequential manner, using the Allen Wrench(②) : Step 5.1. ) FULLY Tighten ALL 4( four ) bolts in the Backrest and Armrests. Step 5.2. ) FULLY Tighten ALL 4( four ) bolts at the INNER edges of the Front Apron.
Step 6 Right Armrest(C) Left Armrest(B) Front Rail(E) Leg(G) ① Install the Leg(G) at the bottom of Left Armrest(B) and Right Armrest(C) by placing Plastic Washer(①) on the threaded stem.Then insert threaded stem into the threaded mounting postion at the bottom of Left Armrest(B) and Right Armrest(C).Tighten by turning the Leg clockwise. Note: The use of Plastic Washer(①) are OPTIONAL and are especially useful to help alleviate slight wobbles.
Turn the Sofa to its upright position. Place the Seat Cushions(F) onto the Sofa. Step 8 Your Sofa is ready for use. This Sofa can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 11 OF 11