WARNING! Furniture Tipping Risk. Serious risk of severe or fatal crush injuries can occur from furniture tipping over If not secured. Children like fo climb on furniture and Unsecured furniture can pose a serious danger. Please follow all Instructions and Install the tip-over restraints provided. In addition to installing the restraints, to help prevent tip-over: 1. Place heaviest items in the lowest drawers, 2.
Assembly Instructions Caution : You must read this before you proceed COAT RACK Part list Label Picture Description QTY A BOTTOM PART 1 Noble House Home Furnishings LLC Page 2 OF 13
Label Picture Description QTY B LOWER 2 SUPPORT C UPPER 2 SUPPORT E a Hanger Strip 1 Noble House Home Furnishings LLC Page 3 OF 13
Hardware Label Picture Description QTY N Ni Flat Head Allen Bolt @® OY (M6x16mm) 17 Ellen Key (4mm Allen Key (4 1 Tip over Restraint ® te Device 2 @ Wall Plugs Screw Wall Plugs Bracket 2 Screwdriver =r @ : (Not Provided) 1 Hammer (— (Not Provided) 1 Power drill © a J (Not Provided) 1 Noble House Home Furnishings LLC Page 4 OF 13
Assembly preparation Before beginning 2 oe assembly ’ x17 Pcs. Pcs. Pcs. Pcs. Pcs. Pcs. Read instructions, cover to cover.
Assembly steps Overview Hanger Strip © Bottom Part i | Top (D) — Upper Support (C) — Lower Support (B) N FRONT FACING This Coat Rack has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Coat Rack parts, the picture above will help you, to put the various parts into perspective. Please read through the instructions below, to familiarize the parts and steps before assembly.
Pcs. Pcs. Pcs. Pcs. Pcs. Unpack all the parts and place it on a clean and non marring surface gently. Step 2 Take the Lower Support (B) and insert it in Bottom part (A). Tighten the Flat Head Allen Bolt (1) with the help of Allen key (2) as shown in the picture above.
(C)— 4 Insert the Upper Support (C) in Lower Support (B) with matching holes. Tighten the Flat Head Allen Bolt (1) with the help of Allen key as shown in the picture above.
Insert the Top (D) with matching holes of Upper Support (C). Tighten the Flat Head Allen Bolt with the help of Allen key as shown in the picture above.
Take the Hanger Strip (E) and align it with matching holes of Top (D). Tighten the Flat Head Allen Bolt (1) with the help of Allen key (2) as shown in the picture above.
Tip over Restraint Device Installation Instructions Lvs Serious or fatal crushing injuries can occur from tipping furniture. To help prevent tip-over: ALWAYS secure this furniture to the wall using Tip over Restraint Device. See product instructions for more ways to help prevent furniture tip-over.
9.1) oo two holes on wall at same height as Brackets (6) on Coat Rack with Power Drill (9). You can mark these points in two ways as below: 1) Move the Coat Rack back to the wall. Mark two points same height as Coat Rack on the wall. Note: The Brackets need to be secured to solid, load bearing surface. Please use a Stud Finder(not supplied) if needed to locate the Wall Frame. 2) Measure the height of the Brackets with ruler/measuring tape and mark on wall to keep them accurate and same height. 9.
Move Coat Rack to the wall. Pull the Tip over Restraint Strap through the Brackets (6) on the wall and Coat Rack one by one, and pull the Tip over Restraint Straps tight. This Coat Rack is now ready to use. Caution: This Coat Rack can only be used on flat, level surface. Care & Maintenance Ji Furniture may scratch floors. We recommend using furniture pads ) to protect your floors. not put hot items directly on furniture surface not clean furniture with harsh cleansers or polish.
