Owner's Manual

ManualsBrandsNiles ManualsAudioNiles PS6Si

ONE-SPEAKER STEREO MODE VS TWO-SPEAKER STEREO MODE

One-speaker stereo mode has the advantage of covering a larger area than the two-speaker

stereo mode. The trade off between the two conﬁgurations is volume. The two-speaker stereo

conﬁgurations will be able to play louder in its area than the one-speaker stereo conﬁguration.

INCORPORATING A VOLUME CONTROL

It is possible to control the volume of the sound at the speaker location. Volume controls are

connected in line with the speaker. An example of wiring an area with 2 speakers and a master

volume control is shown in Figure 2 for one-speaker stereo mode, and Figure 3 for two-speaker

stereo mode. It is usually desirable to control the volume of the speakers in different areas or

zones of the outdoor system. A suggested way to accomplish this is shown in Figure 4 for one-

speaker stereo mode, and Figure 5 for two-speaker stereo mode.

Niles recommends our standard weatherproof volume control, WVC100 series or our weatherproof

muting volume control, WMVC series. In addition to controlling the volume of the loudspeakers,

these controls allow the addition of added speakers without adding more ampliﬁer channels.

INSTALLATION

CONNECTING THE LOUDSPEAKER IN ONE-SPEAKER STEREO MODE

1. Strip two to three inches of each speaker cables’ outer jacket away from the insulated

conductors. Ensure that at least two inches of the separate conductors are free.

2. Strip one half inch of insulation from the end of each conductor for both connection cables.

3. Observe proper phasing when performing the following: Choose the speaker cable that is

labeled for the “Right” ampliﬁer channel. Using a wire nut, connect one stripped end of the

“Right” speaker cable to the PS6Si connection cable’s red wire. The wire nut will protect

the stripped ends of the wire. If added protection is desired, place a large amount of silicon

sealant so the bottom of the wire nut is encased and sealed. Repeat with the PS6Si connec-

tion cable’s black wire and the other stripped ampliﬁer “Right” speaker cable’s conductor.

5. Repeat steps 3 and 4 for the “Left” speaker cable and the PS6Si’s connection cable with

the “yellow/black” pair of conductors.

6. Connect the opposite end of the speaker cables to the ampliﬁer or receiver. Start by per-

forming step 1 and 2 on the speaker cable near the ampliﬁer. Use the cable labeled “Right”

and attach the same conductor you attached to the red loudspeaker wire to the positive

(red) or (+) “Right” ampliﬁer output terminal. Attach the other conductor in that cable to the

ampliﬁer’s “Right” negative (black) or (–) ampliﬁer output terminal.

7. Using the cable labeled “Left” attach the same conductor you attached to the yellow loud-

speaker wire to the positive (red) or (+) “Left” ampliﬁer output terminal. Attach the other con-

ductor in that cable to the ampliﬁer’s “Left” negative (black) or (–) ampliﬁer output terminal.

CONNECTING THE LOUDSPEAKER IN TWO-SPEAKER STEREO MODE

1. Strip two to three inches of each speaker cables’ outer jacket away from the insulated

conductors. Ensure that at least two inches of the separate conductors are free.

2. Strip one half inch of insulation from the end of each conductor for both connection cables.

3. Connect one stripped end of the speaker cable coming from the ampliﬁer to the PS6Si

connection cable’s red wire of one cable and the PS6Si connection cable’s yellow wire. To

connect the three wires, twist the stripped ends of the wire together and screw down the

wire nut on the twisted wires. The material inside the wire nut will protect the stripped ends

of the wire. However, if added protection is desired, place a large amount of silicon sealant

so the bottom of the wire nut is encased and sealed. Pay attention to the markings on the

speaker cable. Each loudspeaker you connect must be connected to the ampliﬁer’s speaker

wire in the same way.

4. Repeat step 3 with the PS6Si connection cable’s black wires and the other stripped ampli-

ﬁer speaker cable’s conductor.

5. Connect the opposite end of the speaker cable to the ampliﬁer or receiver. Start by

performing step 1 and 2 on the speaker cable near the ampliﬁer. Paying attention to the

markings on the speaker cable conductor, attach the same conductor you attached to the

red loudspeaker wire to the positive (red) or (+) ampliﬁer output terminal. Attach the other

conductor to the ampliﬁer’s negative (black) or (–) ampliﬁer output terminal.

TROUBLESHOOTING

VERIFY SYSTEM OPERATION AND LOUDSPEAKER COVERAGE

1. Turn the system “On” and play music to the speakers. Set the Volume controls to a level

that allows the speakers to be easily heard over the “noise” in the area.

2. Verify that music is playing through each speaker. If not, trouble shoot the wiring and make

sure each speaker is electrically connected to the ampliﬁer.

3. Verify that each speaker is connected to the proper channel of the ampliﬁer. To do this,

change the balance of your speakers on your ampliﬁer or receiver so that one channel is

playing loudly and the other is not. Verify that each speaker or each side of the speaker is

attached to the proper channel of the ampliﬁer. If they are not, correct the wiring on the

loudspeaker that is not connected properly. Reset the balance on the ampliﬁer or receiver

so both channels have a similar volume level.

4. If you used a volume control between the ampliﬁer and the speakers, verify that it is

controlling the volume of the loudspeakers in its zone. Repeat this for every volume control

in the system. If it is not, correct the wiring.

5. Position the loudspeakers per the layout and verify that the sound is even and consistent

throughout the area.

Figure 2. One-speaker stereo, one zone volume control wiring

Zone 1

Zone

Zone 1

Zone

Zone 2

Zone 1

Zone 2

Zone

Zone 1

Zone

Zone 2

Figure 3. Two-speaker stereo, one zone volume control wiring

Figure 4. One-speaker stereo, two zone volume control wiring

Figure 5. Two-speaker stereo, two zone volume control wiring

DS00487A-1 PS6Si Planter Speaker.indd 2 5/16/06 3:42:33 PM