European Siding System Horizontal Installation Guide v20231116US
CONTENTS Important Note 3-5 European Siding Parts 6-9 Under Construction 10 Furring Strips Installation 11 Expansion and Contraction Values Table 12 Locking the Siding Board 13 - 15 European Siding System Horizontal Installation -Framing 16 - 18 -Trim Installation 18 - 20 -Siding Board Installation 20 - 26 -Finish the Top 27 NOTE: Click on the heading to enter the section directly Click to return to Content Table European Siding System-Horizontal Installation Guide / v20231116US 2
IMPORTANT Note: Read All Sections Before You Start For the most up to date information, please visit our website @ www.newtechwood.com Prior to installing any composite siding system, it is recommended that you check with local building codes for any special requirements or restrictions. The diagrams and instructions outlined in this guide are for illustration purposes only and are not meant or implied to replace a licensed professional.
Static Static can also be more prevalent in areas that are of higher altitude because the humidity is lower. For these areas, be careful of using conducive objects such as metal railing and chairs as static shocks might occur more often. A potential way to lower the amount of static shocks occurring is to apply Staticide (www.aclstaticide.com) on your deck or use anti-static mats before doorways. Ventilation NewTechWood products CANNOT be directly installed onto a flat surface.
Predrill It is recommended to use the #8 pan head screw for face fixing the profiles and the trims onto the furring strips. When face fixing, it is recommended to predrill the holes slightly larger on the profiles and the trims to allow for expansion and contraction response to temperature change, as shown in below diagram, The predrilled hole size should be larger than the screw thread size, from 1/16” (1.5 mm) to 5 /64” (2 mm).
European Siding Parts Product Purpose Part AW-02 Used for the installation of the first board AW-08 Used at every joist to fix each board to the furring strip T-7 Used on the supporting for the last board UH46 European Siding Board UH50 F-Trim, used for the UH46 installation on the outermost edge US73 F-Trim, used for the UH46 installation on the outermost edge Click to return to Content Table European Siding System-Horizontal Installation Guide / v20231116US 6
European Siding Parts Product Purpose UH51 Outside Corner Trim, used for the UH46 installation on the outside corners UH58 European Siding Board UH59 F-Trim, used for the UH58 installation on the outermost edge UH60 Outside Corner Trim, used for the UH58 installation on the outside corners Click to return to Content Table Part European Siding System-Horizontal Installation Guide / v20231116US 7
European Siding Screws (For Wood Furring Strip) The table below shows the screws recommended to use for the installation, but not included.
European Siding Screws (For Aluminum Furring Strip) The table below shows the screws recommended to use for the installation, but not included.
Under Construction We recommend for the under construction aluminum or pressure treated wood furring strips. Each siding board needs to be supported by a furring strip NO MORE than 16" (406mm) from center to center. Extra care is required in order to provide sufficient joisting in and around obstacles such as windows, fascia’s, soffits, guttering, ventilation points etc.
Furring Strips Installation A building professional should be consulted regarding vapor barriers and insulation for your project. Where a vapor barrier is to be used, it should be a breathable type and must be positioned behind the furring strips. The furring strip needs to have a minimum thickness of 1" (25mm). Wood furring strips should be fixed into position at a maximum of 16" (406mm) centers using a suitable A4 Stainless Steel Countersunk Wood/Masonry screw.
Expansion and Contraction Values NewTechWood siding boards will experience expansion and contraction with changes in temperature. Expansion and contraction are most significant where extreme temperature changes occur. Fastening the deck planks according to the gapping requirements noted in the following table accommodates for this movement.
Locking the Siding Board Since the composite wood must allow for expansion and contraction due to temperature change, the board must be locked at one fixed point but only one point to allow the remaining board to expand and contract freely. In the case there is a need to lock the board, Clip (AW08) comes with a separate hole. It is important that DO NOT LOCK any other clips for the same board.
- Horizontal Installation - Wood Furring Strips Wood Furring Strip #8 x 1" #5 x 1 1/4" (Locking the board) Clip (AW08) Siding Board Starting Trim (AW02) When installing horizontally, it is required to lock the Clip (AW08) at the middle of the board, as shown in Diagram A1 .
- Butt Joint Installation - Butt Joint Installation - Two Boards only Locking with screw at the butt joint side of each board Furring Strip Clip (AW08) Siding Board No Locking No Locking Locking with Screw Locking with Screw Expansion & Contraction No Locking No Locking Expansion & Contraction Floor Butt Joint Installation - Three or more Boards Locking with screw at the middle of each board Furring Strip No Locking Clip (AW08) Locking with Screw No Locking Expansion & Contraction Siding B
European Siding System Horizontal Installation Installation Procedure Step 1: Framing - Measure and Chalk the joists - Furring Strips Installation Step 2: Trim Installation Step 3: Siding Board Installation - Installing the First course - Installing the Second course - Continuing the remaining installation - Installing the Last board Step 4: Finish the Top 1 Framing The frame needs to be level before installing the siding boards.
2 Measure and chalk the furring strips according to the span data specified on page 10 of this installation guide, as shown in Diagram 2 . 3 Fix the furring strips onto the wall that you intend to install with screws at least 19 5/8” (500mm) and max to 39 3/8” (1000mm) on center, as shown in Diagram 3 . Detail 3-3 Detail 3-4 Min 19 5/8" (500mm) Max 39 3/8" (1000mm) Detail 3-2 Detail 3-1 Diagram 2 Diagram 3 Note: Note: 1. We are using wood furring strips for this installation.
1 1/8" (28mm) 4 1 3/4" (45mm) Wall Furring Strip Trim Installation Secure the F-Trim (UH50) onto the wall outermost edge joist and the Outside Corner Trim (UH51) onto the wall outside corner joist with screws at least 19 5/8" (500mm) and max to 39 3/8" (1000mm) on center, respectively, as shown in Diagram 4 .
5 Install the Starting Trim (AW02) at the end of the joists opposite the floor with screws, as shown in Diagram 5 . Furring Strip Wall Starting Trim (AW02) min 3/16" (5mm) F-Trim (US73) Detail 5-2 Detail 5-1 Starting Trim (AW02) Min 7/16" (11mm) Diagram 5 Note: 1. Outermost Edge A minimum gap of 3/16" (5mm) needs to be left between the Starting Trim (AW02) and the F-Trim (UH50), as shown in Detail 5-1 and 5-2 . 2.
Note: Fasten the Starting Trim (AW02) with a clearance of 1 3/4" (45mm) above the floor, as shown in Detail 5-4 . Furring Strip Siding Board Installation Installing the First course Put the first European Siding Board (UH46) over the Starting Trim (AW02) and fasten it onto the furring strip with Clip (AW08), as shown in Diagram 6 and Detail 6-1 .
Note: Since the composite wood must allow for expansion and contraction due to temperature change, the board must be locked at one fixed point but only one point to allow the remaining board to move freely. When installing horizontally, it is required to lock the Clip (AW08) at the middle of each board, as shown in Detail 6-2 . DO NOT LOCK any other Clips (AW08) for the same board. Please review page 13 , "Locking the Siding Board" of this installation guide for further information.
7 Installing the Second course Gap for Expansion & Contraction Gap for Expansion & Contraction Put the second board over the first board's Clip (AW08) and fasten it onto the furring strip with the Clip (AW08), as shown in Diagram 7 , Detail 7-1 , Detail 7-2 .
/TYZGRROTM ZNK 9KIUTJ )U[XYK Board (UH46) Wall 8 Installing the Last board When you are at the last board, measure the distance between the top of the furring strip and the Clip (AW08), as shown in Diagram 8 and Detail 8-1 .
9 Cut the board according to the measured dimension and the selected option on how to finish the top, as shown in Diagram 9 and Detail 9-1 . Option 1 Finish the top with cut F-Trim (UH50), as shown in Detail 9-2 . Cutting Dimension " B " = "A" (measured dimension) - 11/16" (18mm) 11/16" (18mm) Finish the top with Cut F-Trim (UH50) Wall Last Board Furring Strip Detail 9-2 Option 2 No Finish the top or Finish the Top with metal flashing, as shown in Detail 9-3 .
10 Install the Rubber Stopper (T-7) onto each furring strip with screws, as shown in Diagram 10 . Option 2 No Finish the Top or Finish the Top with Metal Flashing: Install the Rubber Stopper, as shown in Detail 10-2 .
11 Put the cut siding board over the Clip (AW08) in place and then face fix it onto each furring strip along the length of the board against the Rubber Stopper (T-7), as shown in Diagram 11 . Option 2 Finish the top with Metal Flashing: Install the last board, as shown in Detail 11-2 .
12 Finish the Top Sealant Glue There are two options to finish the top of the siding. Cut F-Trim (UH50) Finish the Top Wall Furring Strip Board (UH46) Detail 12-2 Option 2 Using Metal Flashing: Put a Metal Flashing over the top of the siding and fix it onto the furring strip with screws, as shown in Detail 12-3 .
European Siding System Horizontal Installation Guide v20231116US ©2023 Newtechwood Corporation. NewTechWood® is a registered trademark of Newtechwood Corporation. To obtain a copy of the most current version of this installation guide, visit us online at www.newtechwood.com.
European Siding System Vertical Installation Guide v20231115US
U CONTENTS Important Note 3-5 European Siding Parts 6-9 Under Construction 10 Furring Strips Installation 11 Expansion and Contraction Values Table 12 Locking the Siding Board 13 - 14 European Siding System Vertical Installation -Framing 15 - 17 -Trim Installation 18 -Siding Board Installation 18 - 25 -Finish the Top 25 NOTE: Click on the heading to enter the section directly Click to return to Content Table European Siding System-Vertical Installation Guide / v20231115US 2
IMPORTANT Note: Read All Sections Before You Start For the most up to date information, please visit our website @ www.newtechwood.com Prior to installing any composite siding system, it is recommended that you check with local building codes for any special requirements or restrictions. The diagrams and instructions outlined in this guide are for illustration purposes only and are not meant or implied to replace a licensed professional.
U Static Static can also be more prevalent in areas that are of higher altitude because the humidity is lower. For these areas, be careful of using conducive objects such as metal railing and chairs as static shocks might occur more often. A potential way to lower the amount of static shocks occurring is to apply Staticide (www.aclstaticide.com) on your deck or use anti-static mats before doorways. Ventilation NewTechWood products CANNOT be directly installed onto a flat surface.
Predrill It is recommended to use the #8 pan head screw for face fixing the profiles and the trims onto the furrinf strip. When face fixing, it is recommended to predrill the holes slightly larger on the profiles and the trims to allow for expansion and contraction response to temperature change, as shown in below diagram, Screw's Head Size Profiles or Trims Screw's Shank Size Predrilled Hole Size The predrilled hole size should be larger than the screw thread size, from 1/16” (1.5 mm) to 5 /64” (2 mm).
U European Siding Parts Product Purpose Part AW-02 Used for the installation of the first board AW-08 Used at every furring strip to fix each board onto the furring strip T-7 Used on the supporting for the last board UH46 European Siding Board UH50 F-Trim, used for the UH46 installation on the outermost edge US73 F-Trim, used for the UH46 installation on the outermost edge Click to return to Content Table European Siding System-Vertical Installation Guide / v20231115US 6
European Siding Parts Product Purpose UH51 Outside Corner Trim, used for the UH46 installation on the outside corners UH58 European Siding Board UH59 F-Trim, used for the UH58 installation on the outermost edge UH60 Outside Corner Trim, used for the UH58 installation on the outside corners Click to return to Content Table Part European Siding System-Vertical Installation Guide / v20231115US 7
U European Siding Screws (For Wood Furring Strips) The table below shows the screws recommended to use for the installation, but not included.
European Siding Screws (For Aluminum Strips) The table below shows the screws recommended to use for the installation, but not included.
U Under Construction We recommend for the under construction aluminum or pressure treated wood furring strips. Each siding board needs to be supported by a furring strip NO MORE than 16" (406mm) from center to center. Extra care is required in order to provide sufficient joisting in and around obstacles such as windows, fascia’s, soffits, guttering, ventilation points etc.
Furring Strips Installation A building professional should be consulted regarding vapor barriers and insulation for your project. Where a vapor barrier is to be used, it should be a breathable type and must be positioned behind the furring strips. The furring strip needs to have a minimum thickness of 1" (25mm). Wood furring strips should be fixed into position at a maximum of 16" (406mm) centers using a suitable A4 Stainless Steel Countersunk Wood/Masonry screw.
U Expansion and Contraction Values NewTechWood siding boards will experience expansion and contraction with changes in temperature. Expansion and contraction are most significant where extreme temperature changes occur. Fastening the deck planks according to the gapping requirements noted in the following table accommodates for this movement.
Locking the Siding Board Since the composite wood must allow for expansion and contraction due to temperature change, the board must be locked at one or two adjacent fixed points to allow the remaining board to expand and contract freely. In the case there is a need to lock the board, Clip (AW08) comes with a separate hole. It is important that DO NOT LOCK any other clips for the same board.
U - Vertical Installation - Wood Furring Strip Wood Furring Strip Siding Board #8 x 1" Clip (AW08) #5 x 1 1/4" (Locking the board) When installing vertically, it is required to lock the Clip (AW08) at the top of the board to allow the remaining board to expand and contract freely. Note: 1. When the board's length is below 78 3/4" (2m), it is only to lock the first clip (AW08) at the top of the board, as shown in Diagram A1 . 2.
European Siding System Vertical Installation Installation Procedure Step 1: Framing - Measure and Chalk the Furring Strips - Furring Strips Installation Step 2: Trim Installation Step 3: Siding Board Installation - Installing the First course - Installing the Second course - Continuing the remaining installation - Installing the Last board Step 4: Finish the Top 16 Framing The frame needs to be level before installing the siding boards.
U 17 Measure and chalk the furring strips according to the span data specified on page 10 of this installation guide, as shown in Diagram 17 . 18 Fix the furring strips onto the wall that you intend to install with screws in distance at least 19 5/8” (500mm) and max to 39 3/8” (1000mm) on center, as shown in Diagram 18 . Detail 18-3 Detail 18-1 Detail 18-4 Detail 18-2 Min 19 5/8" (500mm) Max 39 3/8" (1000mm) Detail 18-5 Diagram 17 Diagram 18 Note: 2.
Note: 2 . A m i n i m u m g a p o f 3 / 8 " ( 1 0 m m) needs to be left between the Ceiling and the furring strip's end, as shown in Detail 18-2 . Wall Ceiling 3/8" (10mm) Wall Furring Strip Detail 18-4 Furring Strip Detail 18-2 Wall Note: 3. For the Outermost Edge, please install according to Detail 18-3 . Furring Strip 4. For the Inside Corner, please install according to Detail 18-4 . 5. For the Outside Corner, please install according to Detail 18-5 .
U 19 Trim Installation 20 Secure the F-Trim (UH50/US73) onto the wall outermost edge furring strip and the Outside Corner Trim (UH51) onto the wall outside corner furring strip with screws in distance at least 19 5/8" (500mm) and max to 39 3/8" (1000mm) on center, respectively, as shown in Diagram 19 . Siding Board Installation Installing the First course Start the installation according to the Diagram 20 .
21 Put the first European Siding Board (UH46) in place over the trims, then face fix it the side next to the F-Trim (UH50/US73) onto the furring strip with screws, and fasten it's another side onto the furring strip with Clip (AW08), as shown in Diagram 21 , Outermost edge Detail 21-1 and Outside Corner Detail 21-2 . Note: Pre-drill the face fixing holes on the first board before installation to allow for expansion and contraction.
U Note: Since the composite wood must allow for expansion and contraction due to temperature change, lock the board at one or two adjacent fixed points to enable the remaining board to move freely. When installing vertically, it is required to lock the Clip (AW08) at the top of each board, as shown in Detail 21-4 .
Note: Since the composite wood must allow for expansion and contraction due to temperature change, lock the board at one or two adjacent fixed points to enable the remaining board to move freely. When installing vertically, it is required to lock the Clip (AW08) at the top of each board, as shown in Detail 22-1 . IT IS IMPORTANT to review page 13 , "Locking the Siding Board" of this installation guide for further information.
U 23 Installing the Last board When you are at the last board, measure the distance between the trim or the adjacent installed siding board and the Clip (AW08) to obtain the appropriate board's cutting dimension, as shown in Diagram 23 . Furring Strip Wall Board (UH46) "A" Clip (AW08) Detail 23-3 Furring Strip Board (UH46) Board (UH46) Diagram 23 1. Outermost Edge with F-Trim (UH50/US73), as shown in Detail 23-1 and 23-2 . 2.
24 Cut the board according to the measured dimension, as shown in Diagram 24 and Detail 24-1 . Cut 25 Install the Rubber Stopper (T-7) onto the furring strip in the Inside Corner to back up the last board, as shown in Diagram 25 .
U 26 Put the cut siding board over the Clip (AW08) in place and then face fix it onto the furring strip with screws, as shown in Diagram 26 . Note: Pre-drill the face fixing holes on the last board before installation to allow for expansion and contraction. Please review page 5 , "Predrill ", of this installation guide for further information. Cut Siding Board (UH46) Detail 26-1 and 26-2 shows the last board installation on the Outermost Edge with F-Trim (UH50)/US73).
Detail 26-3 shows the last board installation on the Outside Corner with Outside Corner Trim (UH51). It is recommended below two options to finish the top of the siding. Face fixing the board onto the furring strip Wall Furring Strip 27 Finish the Top Finish the Top Clip (AW08) Cut Siding Board (UH46) Outside Corner Trim (UH51) Detail 26-3 Detail 26-4 and Detail 26-5 show the last board installation in the Inside Corner .
U Option 2 Using F-Trim (UH50): Put F-Trim (UH50) against the top of the siding along the legth of the installed siding boards and secure it onto the wall with screws, as shown in Detail 27-2 .
European Siding System Vertical Installation Guide v20231115US ©2023 Newtechwood Corporation. NewTechWood® is a registered trademark of Newtechwood Corporation. To obtain a copy of the most current version of this installation guide, visit us online at www.newtechwood.com.
European Siding System Windows Installation Guide v20220508US
CONTENTS Introduction 4 Installing the Furring Strips 5-7 Installing the trims around the window frame 8 - 10 Installing the boards 11 - 26 European Siding System - Window and Doors Installation Guide / v20220508US 2
Window Reveals Installation Use the F-Trim UH50, picture framing the window, as shown below, Wall Window Frame F-Trim (UH50) Window Opening European Siding System - Window and Doors Installation Guide / v20220508US 3
1 Fix the furring strips onto the wall according to the span data specified on page Furring Strips Installation , of this installation guide. It is necessary to install two furring strips width of at least 3 15/16" (100 mm) next to the sides of the window frame for the horizontal installation or against the window head and the windowsill for the vertical installation.
3 15/16" (100mm) min 16" (406mm) 16" (406mm) max max Furring Strips 3 1/8" (80mm) min 3 1/8" (80mm) min 16" (406mm) max Detail 1-2-1 Detail 1-2-2 Window Frame Diagram 1-2 For Siding Vertical Installation Window Frame 9/16" (15mm) 9/16" (15mm) Furring Strips Window Frame Detail 1-2-1 Furring Strips Detail 1-2-2 European Siding System - Window and Doors Installation Guide / v20220508US 5
2 Measure the width and the height of the window frame, as shown in Diagram 2-1 (Horizontal Installation) and Diagram 2-2 (Vertical Installation).
3 Mitre cut the F-Trim (UH50) according to the measurement, as shown in Diagram 3 .
4 Secure the mitre cut End-trims onto the furring strips with screws in the max distance of 19 11/16" (500 mm) on center, picture framing the window. Siding Horizontal Installation, as shown in Diagram 4-1 , Detail 4-1-1, and Detail 4-1-2 . Siding Vertical Installation, as shown in Diagram 4-2 , Detail 4-2-1 , and Detail 4-2-2 .
F-Trim (UH50) Furring strips Detail 4-2-1 Detail 4-2-2 Window Frame Diagram 4-2 For Siding Vertical Installation Furring Strip Window Frame F-Trim UH50 Wall Wall Furring Strip F-Trim UH50 View from the Top Detail 4-2-1 Window Frame View from the Side Detail 4-2-2 European Siding System - Window and Doors Installation Guide / v20220508US 9
5 Install the boards against the Clips (AW08), and lock the boards according to the instruction on page "Locking the Siding Board" of this installation guide. Siding Horizontal Installation, as shown in Diagram 5-1 , Detail 5-1-1, and Detail 5-1-2 . Siding Vertical Installation, as shown in Diagram 5-2 , Detail 5-2-1 , and Detail 5-2-2 .
Detail 5-2-1 Detail 5-2-2 Diagram 5-2 Wall F-Trim UH50 Window Frame C Last Board Window Frame D F-Trim (UH50) Detail 5-2-2 F-Trim UH50 Detail 5-2-1 European Siding System - Window and Doors Installation Guide / v20220508US 11
6 Refer to the measurement to determine how to cut the notch on the board to get the appropriate gap between the trim. Siding Horizontal Installation, as shown in Diagram 6-1 . Siding Vertical Installation, as shown in Diagram 6-2 . Please Note: It is recommended to cut the board, as shown in Detail 6-1 . Don't cut the board on the raised portion, as shown in Detail 6-2.
Detail 6-3 and Detail 6-4 present the installation details when the rip point is at A or B. Furring Strip Wall When the rip point occurs at C or D, use a rubber stopper T-7 instead the Clip AW08 and face fix the boards, as shown in Detail 6-5 and Detail 6-6 .
C+3/8" (10mm) H ≦D+3/8" (9mm) Center Line Diagram 6-1 For Siding Horizontal Installation CUT H-H ≦D+3/8" (9mm) H H Center Line C+Gap value x 2 H-H H CUT Diagram 6-2 For Siding Vertical Installation European Siding System - Windows and Doors Installation Guide / v20220508US 14
7 Put the ripped board in place against the Clips (AW08); Siding Horizontal Installation, Face fix the section of the board underside the windowsill with screws onto the furring strips. Except for the middle screw, predrill the screw holes to allow the board for expansion and contraction. Then lock the board onto the furring strip with the middle screw, also do not lock any other Clip (AW08) for the same board, as shown in Diagram 7-1 , and Detail 7-1-1 .
Siding Vertical Installation, Lock the Clip (AW08) at the top of the board only, do not lock any other Clips (AW08) for the same board, as shown in Diagram 7-2 , and Detail 7-2-1 . Note: Please review page 13 , "Locking the Siding Board" of this installation guide for further information.
8 Install the boards against the sides of the window or the window head and the windowsill. Siding Horizontal Installation, We recommend having a 3/16" (5 mm) clearance between the F-Trim (UH50) and the boards, as shown in Diagram 8-1 , and Detail 8-1-1 . Next, lock the Clip (AW08), which is next to the window frame, to allow the board for expansion and contraction outward the window frame in one direction, as shown in Detail 8-1-2 .
Siding Vertical Installation, It is vital to have a gap between the board and the F-Trim (UH50) to avoid warping or buckling, as shown in Diagram 8-2 , and Detail 8-2-1 . Next, lock the Clip (AW08) at the top of each board only, do not lock any other Clip (AW08) for the same board, as shown in Detail 8-2-2 . Please Note: Please review page 13 , "Locking the Siding Board" of this installation guide for further information.
9 When you are at the window head or the window side, measure the distance between the two F-Trims (UH50) and the distance between the F-Trim (UH50) and the Clip (AW08) to have the measurement for the notch cutting. Siding Horizontal Installation, as shown in Diagram 9-1 , Detail 9-1-1 , and Detail 9-1-2 . Siding Vertical Installation, as shown in Diagram 9-2 , Detail 9-2-1 , and Detail 9-2-2 .
C Detail 9-2-1 Detail 9-2-2 E Boards Diagram 9-2 Wall FTrim UH50 Last Board Clip (AW08) C Window Frame E F-Trim (UH50) View from the Top Detail 9-2-2 F-Trim UH50 Detail 9-2-1 European Siding System - Windows and Doors Installation Guide / v20220508US 20
10 Cut a notch on the board according to the measurement; Siding Horizontal Installation, as shown in Diagram 10-1 . Siding Vertical Installation, as shown in Diagram 10-2 . Please Note: it is recommended to cut the board, as shown in Detail 10-1 . Don't cut the board on the raised portion, as shown in Detail 10-2.
Detail 10-3 and Detail 10-4 present the installation details when the rip point is at A or B. Furring Strip Wall When the rip point occurs at C or D, use a rubber stopper T-7 instead the Clip AW08 and face fix the boards, as shown in Detail 10-5 and Detail 10-6 .
H ≧ E+3/8" (9mm) Center Line C+3/8" (10mm) Diagram 10-1 For Siding Horizontal Installation CUT H-H ≧E+3/8" (9mm) C+Gap value x 2 H-H H CUT H H Center Line Diagram 10-2 For Siding Vertical Installation European Siding System - Window and Doors Installation Guide / v20220508US 23
11 Put the ripped board in place against the Clip (AW08); Siding Horizontal Installation, Lock the Clip (AW08) at the middle of the board 0nto the batten with a screw, do not lock any other Clip (AW08) of the same board, as shown in Diagram 11-1 , and Detail 11-1-1 .
Siding Vertical Installation, Lock the Clip (AW08) at the top of the board only, do not lock any other Clip (AW08) of the same board, as shown in Diagram 11-2 , and Detail 11-2-1 .
12 Continuous the remaining board installation according to the European Siding board installation steps.
European Siding System Windows Installation Guide v20220508US ©2022 Newtechwood Corporation NewTechWood® is a registered trademark of Newtechwood Corporation. To obtain a copy of the most current version of this installation guide, visit us online at www.newtechwood.
