SKU: NIF20CBK00 20" 2-in-1 High Velocity Wall Mounted or Floor Fan OWNER’S MANUAL Read and save these instructions. Manual v1.
READ AND SAVE THESE INSTRUCTIONS. TABLE OF CONTENTS Register Your Product Online……………………………………………………………………………3 Safety Information & Warnings ........................................................................... 4 Assembly Instructions .......................................................................................... 7 Operation Instructions ......................................................................................... 9 Cleaning & Maintenance .....................................
Register Your Product Online Register Your NewAir Product Online Today! Take advantage of all the benefits product registration has to offer: Service and Support Diagnose troubleshooting and service issues faster and more accurately Recall Notifications Stay up to date for safety, system updates and recall notifications Special Promotions Opt-in for NewAir promotions and offers Registering your product information online is safe & secure and takes less than 2 minutes to complete: newair.
SAFETY INFORMATION & WARNINGS Intended Use: This product is intended for residential and office use etc. For industrial or other commercial applications use only with electrical wiring that is in good working order and that meets applicable codes and ordinances. If you have any questions whether your wiring is adequate, consult a qualified electrician or contact customer service at support@newair.com. While using your fan, you should follow the IMPORTANT INSTRUCTIONS listed below.
• Avoid the use of extension cords due to risk of fire. If an extension cord must be used, the cord must be minimum 14 AWG and rated not less then 1875 watts. • Do not run the power cord under carpeting. Do not cover the cord with throw rugs, runners or the like. Arrange cord away from traffic area where it will not be tripped over. • Do not insert or allow any object to enter any openings on the fan. Doing so may cause electric shock and/or fire hazard. Avoid contact with moving parts.
WARNINGS WARNING: Shock Hazard • Use your fan only in dry environments. This fan is not intended for use in a bathroom, laundry area, or similar locations, or near sinks, washing machines, swimming pools, or other sources of water. • Never locate fan where it may fall into a bathtub or other water receptacle. Do not use in damp environments such as flooded basements. WARNING: Hot Surfaces • Do not touch fan motor when in use.
ASSEMBLY INSTRUCTIONS ASSEMBLY Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire ‑ rated construction. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities. WARNING: The included mounting parts are intended to be used with drywall anchors only. Do not attempt to mount this unit on the wall or ceiling without proper drywall anchors.
FLOOR STAND ASSEMBLY: 1. Remove the 4 screws from the base tube (fig. 1 & 2) 2. Align the screw hole on the side of the metal plate and the hole on the base tube, then insert the screw and nut to tighten. Do the same thing on the other side of the metal plate. (fig. 3, 4 & 5) 3. Align the screw holes in the middle of the metal plate with the holes in the fan bracket, then insert the screws and nuts to tighten (fig. 6, 7 & 8) newair.
OPERATION INSTRUCTIONS USING YOUR PRODUCT Fan operation: Always operate the fan in an upright position following all instructions and recommendations listed in this manual. Fan location: Place the fan in the area of the room that will provide proper fan cooling. (note: IPX4 outdoor rating is only meant to indicate resistance to occasional water splashes. It does not indicate that the fan is completely water-, dust- or dirt-proof) Fan connection: Plug fan directly into 120 volt A.C., 60 Hz wall outlet.
CLEANING & MAINTENANCE Cleaning: CAUTION-Before cleaning the fan be sure to disconnect power cord from the plug. Clean the grille surface with a clean damp cloth. Do not use harsh chemical or abrasive cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN WATER. Replace the front grille before fan use. Allow fan to dry completely before use. Periodic grille cleaning with a vacuum will prevent dust buildup. The motor is sealed and does not require any interior maintenance, cleaning or lubrication.
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair. Fuse Replacement: 1.
TROUBLESHOOTING Problem The fan will not Operate. The fan is not rotating. Possible Causes The fan is not plugged in and/or the electrical outlet isn’t working properly. Solution Make sure the fan is plugged in and/or the electrical outlet is working properly. The circuit breaker may be tripped or there is a blown fuse. Obstructions are keeping the fan from working. Reset the circuit breaker or check for a broken fuse. Check for obstructions. If you find an obstruction, turn the fan off.
LIMITED MANUFACTURER’S WARRANTY This appliance is covered by a limited manufacturer’s warranty. For one year from the original date of purchase, the manufacturer will repair or replace any parts of this appliance that prove to be defective in materials and workmanship, provided the appliance has been used under normal operating conditions as intended by the manufacturer.
