Full Product Manual

ManualsBrandsmyTouchSmart ManualsDimmers, Switches & OutletsSimple Set Indoor/Outdoor Digital Plug-In Timer

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1 this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may

cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modiﬁcations to this equipment. Such modiﬁcations could void the user’s authority

to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment o and on, the user is encourage to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3(B)/NMB-3(B)

I. Initial Setup

1. Setup

If no numbers are visible on-screen, plug timer into an outlet and let timer charge for 1 hour.

Once charged, press the reset (

) button in the lower right corner using a toothpick or pencil.

2. Set the time

Use up ( ) and down ( ) arrows to set current time, taking note of AM or PM time.

Note: When daylight savings time occurs use the up ( ) and down ( ) arrows to adjust the

time by 1 hour.

II. Programming

1. Choose your custom “my on time”

Press “my on time” (the default time will be ﬂashing), then use up ( ) and down ( ) arrows

to set on time. (If you set the “my on time” earlier than the current time, it will not turn on until the

next day at the time scheduled).

Once you reach the desired “my on time”, either wait 5 seconds, press “my on time” again or press

“my o time” to begin setting the o time.

2. Choose your custom “my o time”

Press “my o time”(the default time will be ﬂashing), then use up ( ) and down ( ) arrows

to set o time.

Once you reach the desired “my o time,” either wait 5 seconds, press “my o time” again or

press other “my on time” to begin setting the next on time.

Repeat steps 1 and 2 to program second set of “my on” and “my o” times.

Note: When a “my on” or “my o” time is set, the active program indicator arrow will appear

on the screen beside the corresponding program number. Programs may run individually or

simultaneously.

Mounting /Installation

1. Mount the timer on a wall near a GFCI receptacle using a screw or nail. Install timer as far above ground level as possible with

receptacle facing downward. Do not install where timer can be immersed or where water will splash or drip onto receptacle.

Screw or nail head must extend at least 3/16” out from the wall (nail or screw not included).

2. Hang the timer, from the hole at the top of the unit.

MADE IN CHINA

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.

This Jasco product comes with a 1-year limited warranty.

Visit www.byjasco.com for warranty details.

Questions? Contact us at 1-800-654-8483 between 7:00AM–8:00PM CST.

36027 VERSION 01 3/15/17

Ratings:

125V 50/60Hz

Max. Load:

10A 1250W General Purpose/Resistive

5A 625W Tungsten

1/4HP Type 3R

Works with dimmable

LED and CFL bulbs.

Outdoor/Indoor Digital

Simple Set

Plug-In Timer

MTS 53003

RISK OF ELECTRIC SHOCK

• PLUG DIRECTLY INTO

A GFCI PROTECTED

ELECTRICAL OUTLET

• UNPLUG TIMER

BEFORE CLEANING

• FULLY INSERT PLUG

• KEEP AWAY FROM CHILDREN

• NOT FOR WATER IMMERSION

• SUITABLE FOR INDOOR

AND OUTDOOR LOCATIONS,

STORE INDOORS WHILE

NOT IN USE.

RISK OF FIRE

• DO NOT USE TO CONTROL

APPLIANCES THAT CONTAIN

HEATING ELEMENTS (COOKING

APPLIANCES, HEATERS,

IRONS, ETC.)

• DO NOT EXCEED

ELECTRICAL RATINGS

• DO NOT USE IF DEVICE

OR CORD IS DAMAGED.

• DO NOT USE WITH AN

EXTENSION CORD

WARNING

Active program

indicator arrow

Indicates if program is set

Clock vs. set

mode indicator

Summary of content (2 pages)

PAGE 1
Outdoor/Indoor Digital Simple Set Plug-In Timer Mounting /Installation 1. Mount the timer on a wall near a GFCI receptacle using a screw or nail. Install timer as far above ground level as possible with receptacle facing downward. Do not install where timer can be immersed or where water will splash or drip onto receptacle. Screw or nail head must extend at least 3/16” out from the wall (nail or screw not included). 2. Hang the timer, from the hole at the top of the unit. I. Initial Setup 1.
PAGE 2
Digital Para Exterior y Interior Fácil de Programar Temporizador Enchufable Montaje/instalación 1. Con un tornillo o clavo, instale el temporizador en una pared cerca de un tomacorriente GFCI. Instale el temporizador lo más alto del nivel del piso posible con el receptáculo en posición hacia abajo. No instale en lugares donde pueda quedar sumergido bajo el agua o donde el agua pueda salpicar o gotear sobre el receptáculo.