Manual

ManualsBrandsMyron L ManualsToolsPT2

4 5

ULTRAPEN

™

PT2

pH & Temperature Pen

PACKAGE CONTENTS:

PT2 Pocket Tester Pen - Battery Installed•

Scoop•

Soaker Cap•

Pocket Clip•

Holster•

Lanyard•

Operating Instructions•

ACCURATE

RELIABLE

SIMPLE

Professional Water Analysis

•

Accuracy of ±0.01 pH

•

Proprietary Sensor Design

•

1, 2 and 3 Point Calibration

•

Automatic Temperature Compensation

•

Temperature Readout

•

Waterproof

•

(Included)

myronl.com

MADE IN USAMADE IN USA

Visit our web sit e:

myronl.com/pt2.htm

ULTRAPEN™ PT3

ORP & Temperature

ULTRAPEN™ PT1

Conductivity, TDS, Salinity

& Temperature

ULTRAPEN™ PT4

Free Chlorine Equivalent

(FC

)

& Temperature

ORIGINAL

EDITED FOR USE

Minimum height 5 mm

Summary of content (6 pages)

PAGE 1
ULTRAPEN ™ PT2 pH & Temperature Pen ORIGINAL EDITED FOR USE Minimum height 5 mm S ACCURATE S RELIABLE S SIMPLE Professional Water Analysis • Accuracy of ±0.
PAGE 2
INTRODUCTION Thank you for purchasing the Myron L ULTRAPEN™ PT2 pH Pen. This instrument is designed to be extremely accurate, fast and simple to use in diverse water quality applications. Advanced features include automatic temperature compensation; highly stable microprocessor-based circuitry; user-intuitive design; and waterproof housing. A true onehanded instrument, the PT2 is easy to calibrate and easy to use. To take a measurement, you simply push a button then dip the pen in solution.
PAGE 3
OPERATING INSTRUCTIONS NOTE: Selecting “ESC” from any menu immediately powers the unit off without saving changes. I. Temperature Unit Selection The PT2 allows you to select the type of units used for displaying temperature: ˚C (Degrees Celsius) or ˚F (Degrees Fahrenheit). To set the preference: 1. Push and release the push button to turn the unit on. 2. Push and hold the button. The display will alternate between “CAL”, “FAC CAL”, “ºCºF TEMP”, “ModE SEL” and “ESC”. 3.
PAGE 4
b. The display will alternate between the final pH and temperature readings. Note the readings for your records. In LIVE mode allow the pen to remain in solution while the LED flashes slowly. The display will alternate between live pH and temperature readings. Note the readings for your records. LIVE measurement will time out after 1 minute OR push and release the push button to power the pen off at any time during LIVE measurement. IV.
PAGE 5
... continued from page 3 7. If the pH 7 calibration is successful, the display will indicate “SAVEd”, then “PUSHCONT” will be displayed. 8. Push and release the push button to continue. The LED will begin flashing rapidly. 9. Repeat steps 5 through 7 with pH 4 or 10 buffer calibration solution. 10. Leave the pen in the same buffer solution until the unit powers off. The offset will be applied to the remaining calibration point. 11. Verify calibration by retesting the calibration solution. D.
PAGE 6
Specifications pH Temperature Range: 0.00-14.00pH 0-71°C/32-160°F Accuracy: ± 0.01pH (After Wet Calibration) ±0.1ºC/±0.1ºF Repeatability: ± 0.01pH ±0.1ºC/±0.1ºF Resolution: 0.01pH 0.1ºC/0.1ºF Time to Reading Stabilization: 10-30 seconds Power Consumption: Active Mode 37mA, Sleep Mode 2µA Temperature Compensation: Automatic to 25ºC Physical Dimensions: 17.15cm L x 1.59cm D or 6.75in. L x 0.625in. D Weight: 54g/1.9oz.