music hall mmf-mark 1 INSTRUCTION MANUAL music hall http: //www.musichallaudio.
You have selected an exceptional turntable. Each component used in the construction of the mmf-mark 1 was selected to provide you with superior performance and the highest level of sound reproduction available today. We know of no turntable that costs as much to produce yet sells for so little. The precise and elegant design of this turntable makes it easy to install and operate.
7. Cleaning Please refer to the MAINTENANCE section for detailed cleaning instructions. 8. Power Sources Connect the turntable only to a power supply of the type and voltage described in the operating instructions or specified on the rear panel of the unit. 9. Power-cord protection Connect the turntable to the power outlet only with the supplied power supply. Do not modify the supplied power supply in any way. Do not attempt to defeat grounding and/or polarization provisions . Do not use extension cords.
6 7 8 9 10 12 11 13 14 15 16 music hall • mmf - mark 1 17 14 13 5
18 PARTS INVENTORY AND OPERATION CONTROL DIAGRAM 1. 2. 3. 4. , 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
GETTING STARTED Thank you for purchasing the music hall mmf-mark 1 turntable. It is a 2-speed belt-driven, audiophile turntable that comes complete with a Ortofon cartridge mounted in a high-quality aluminium tonearm . The alloy platter runs on a precision, stainless steel and brass bearing assembly to provide fluid and quiet operation. These features combine to ensure that the mmf-mark 1 delivers superior audio performance that will provide years of enjoyment.
4. Center the platter (1) over the spindle of the sub-platter (9) and lower it until it rests securely on the sub-platter. 5. Find the counterweight (3). It is in a cut-out in the bottom piece of packing foam. Place the counterweight (3) onto the tonearm. To do this, you are positioned in front of the turntable. Orient the counterweight so that the counterweight number (no. 82) is in the back. Carefully, move the counterweight onto the back of the counterweight support rod.
9. The anti-skating force must be adjusted corresponding to the tracking force. The anti-skating mechanism is calibrated from O to 5g. The anti-skating force should correspond with the tracking force. Three examples of magnetic anti-skating mechanism: a) Tracking force - 1,5g; Anti-skating force 1,5g b) Tracking force-1,7g; Anti-skating force 1,7g c) Tracking force - 2,3g; Anti-skating force 2,3g 10. Slide the dust cover (17) onto the dust cover hinges (13) on the back of the plinth.
To achieve the best sound reproduction, the cartridge must be positioned precisely in the head shell. To do this, fit the tangency guide (you'll find this in the parts bag . It's a white rectangular piece of cardboard with black lines) over the spindle at point 'A' and onto the platter, black lines side up (See diagram below). Remove the stylus guard. Move the tonearm (2) (adjusted for the correct tracking force of your cartridge) to the pattern .
MAINS CONNECTION Locate the wall transformer. It's in a small white box set into the underside of the packing foam. Plug the small male end of the wall transformer wire into the female receptacle on the DC power input (16) for the motor. The DC power input socket (16) for the motor is located on the underside of the turntable near the back. Plug the transformer into the wall. Turn the motor 'ON' (11) and check that the platter (1) spins.
damp cloth. If the turntable is not going to be used for a long period of time, it is advisable to remove the belt from the platter rim to prevent stretching. OIL - The oil supplied for the main bearing provides life-long protection. If oil is lost from the bearing housing, replace it with a single drop of Mobil 1 or other 10w/40 synthetic oil containing Teflon. DUST COVER - This can be cleaned using any commercial acrylic or plastic cleaners.
TROUBLESHOOTING Music hall turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. If, for some reason your turntable is not working properly, please take a few moments to review this list of potential causes. THE PLATTER DOESN'T TURN, ALTHOUGH THE DECK IS SWITCHED ON: • The turntable is not connected to the mains power supply. • No mains at the socket. • The belt is not fitted or has slipped off.
PACKING INSTRUCTIONS Please remove and store the following parts: dust cover (17), platter (1 ), subplatter (9), and belt (7). Fit the stylus guard on the cartridge and lock the tonearm (2). Package the turntable carefully in its original box using thick, 1¼ inch Bubble Wrap.
WARRANTY This entitles you to have the music hall mmf-mark 1 repaired free of charge, at our discretion, for one year after the date of purchase, at any authorized music hall service center, provided the unit was purchased from an authorized dealer. Your original sales receipt is proof of purchase date. Music hall takes no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or unauthorized repair and/or adjustment.