MT100 LAWN TRACTOR Operator’s Manual Model #MYT4213500 Customer Service Number: 855-693-2582 | www.murray.
TABLE OF CONTENTS 1. General Information SECTION 1 General Information................................3 Leveling the Cutting Deck ...........................26 SECTION 2 Operator Safety........................................4 Removing the Cutting Deck .........................27 Save These Instructions..................................4 Adjusting the Tension in the Deck Belt ..........28 Slope Identification Guide .............................4 Changing the Deck Belt ............................
2. Operator Safety Safety Decals The following safety symbols appear on this product. Before you operate the mower, please study them and learn their meaning. Save These Instructions 1. Use a straight edge at least two (2) feet long (A, Fig. 1). A 2x4 or a straight piece of metal works well. IMPORTANT: If the safety decals become worn or damaged, and cannot be read, order replacement decals from your authorized service center. Save these instructions for future reference.
Safety Instructions WARNING: Read and follow all safety rules and instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. CALIFORNIA PROPOSITION 65: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
3. Assembly Instructions NOTICE: This lawn tractor is shipped without gas in the engine. WARNING: If any parts are damaged or missing, do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury. WARNING: Do not attempt to modify this product or create accessories not recommended for use with this product.
Assemble the Steering Wheel 1. Align the steering wheel with the steering shaft, slide the steering wheel down the shaft until into position, and secure the steering wheel with the bolt provided. (Fig. 4) 2. Place the steering wheel cap over the center of the steering wheel, and push downward until it snaps into place. Assemble the Left Deck Anti-scalp Wheel NOTICE: The bottom of the deck anti-scalp wheels should be positioned approximately 1/8 in. - 1/2 in.
4. Features and Controls Check/Adjust the Tire Pressure The following control symbols appear on this product. Before you operate the mower, please study them and learn their meaning. NOTICE: To ensure that the grass is cut level, the right and left front tires must be set to the same pressure. The same is true for the right and left rear tires.
5. Operating the Tractor Ignition Read the Operator Safety section before you operate this machine. Make sure that you know the controls and how to stop the unit. PTO lever (Blade engagement lever) Height of cut lever • Avoid mowing wet grass. • Do not operate the machine under any condition where traction, steering, or stability is in question. Tires could slide even if the wheels are stopped. • Avoid starting and stopping on slopes. • Avoid making sudden changes in speed or direction.
Safety Interlock System Tests Engine 2. Stop the engine and remove the key. Make sure that the oil fill area is clean. Check and Add Engine Oil This machine is equipped with a Safety Interlock System. Do not attempt to bypass or tamper with the switches and devices. 3. Remove the dipstick (Fig. 12 & Fig. 13). Wipe clean the remaining oil from the dipstick. Use Briggs & Stratton® Warranty Certified oils for best performance.
When Adding Fuel • Stop the engine and let the engine cool at least 3 minutes before you remove the fuel cap. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Fill the fuel tank outdoors or in a well-ventilated area. • Do not overfill the fuel tank. To allow for expansion of the fuel, do not fill above the bottom of the fuel tank neck. • Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.
Shifting Gears Depress the brake pedal to slow the mower and bring it to a stop. (Fig. 18) NOTICE: This mower is not equipped with a gas pedal. The travel speed of the mower is controlled by the gear position and throttle position. NOTICE: Do not attempt to shift gears when the moweris in motion. Serious damage to the mower’s transmission could result. Always use the brake pedal to bring the mower to a complete stop before shifting. WARNING: Sharp turns can affect control of the mower.
Adjusting the Deck Anti-Scalp Wheels NOTICE: The bottom of the deck anti-scalp wheels should be positioned approximately 1/8 in. - 1/2 in. off the ground when the mower is at the desired cutting height. This will minimize the chance of scalping the lawn in most situations. • Stop the blade(s) when crossing gravel surfaces. • Do not leave a running machine unattended. Always park on level ground, disengage the attachment, set the parking brake, stop the engine, and remove the key.
6. Maintenance Before adjustments and repairs: • Use ONLY the correct tools. • DO NOT tamper with the governor spring, links, or other parts to increase engine speed. • Replacement parts must be of the same design and installed in the same position as the original parts. Other parts may not perform as well, may damage the unit, void the warranty, and may result in injury.
NOTICE: If raising the side, you will need to turn the top adjustment nut first. If lowering, turn the bottom nut first. 4. Measure again. The deck is properly balanced when both blade tip measurements taken earlier are equal b c a Fig. 23 Fig. 26 a Leveling the Cutting Deck Fig. 25 If your lawn appears unevenly cut after using the tractor, the cutting deck may need adjusting.
Adjusting the Tension in the Deck Belt If you notice a deterioration in cutting performance, it may be necessary to adjust the tension in the deck cable. a Changing the Deck Belt WARNING: Stop the engine, engage the parking brake, and remove the key. WARNING: Stop the engine, engage the parking brake, and remove the key. WARNING: Belts on your tractor are subject to wear and should be replaced if any signs of wear are present.
3. Use a blade removal tool (not provided) to prevent the blade from turning. Checking the Tire Pressure Adjusting the Transaxle Brake 4. Loosen the blade nut by turning it counterclockwise (as viewed from bottom of the mower) using a 24 mm wrench or socket (not provided). For the correct traction and the best mowing performance, make sure that the front tires are inflated to 14 psi and the rear tires inflated to 10 psi. Also, see “Tire Pressure” in the Specifications section.
3. Place the oil drain sleeve (included with tractor) under the drain plug. (Fig. 35) Checking the Mower Blade Stop Time Changing the Air Filter Checking the Spark Plug 4. Place a collection container below the oil drain sleeve. 5. Remove the drain plug. 6. After the oil has drained, re-install the oil drain plug tightly. 7. Refill the engine with new oil. WARNING: DO NOT start or operate the engine without an air filter as it is a fire hazard.
Pushing the Tractor By Hand Pushing the tractor may be necessary for moving the tractor into and out of a garage or shed. It may also be necessary for loading into and out of a trailer. 1. Disengage the Power-Take-Off (PTO). 2. STOP the engine. See Stop the Engine. 3. Shift the transmission into neutral. 4. The rider can be pushed by hand. Towing with the Tractor 7. Transport • Attach equipment ONLY at the hitch point. • The total towed weight (trailer and load) must not exceed 400 lbs.
9. Troubleshooting 8. Storage Fuel System • WARNING: Never store the unit with fuel in an enclosed, non-ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Fuel can become stale when kept in a storage container for more than 30 days. Each time you fill the container with fuel,add STA-BIL 360°® PROTECTION™ to the fuel as specified by the manufacturer’s instructions.
The engine runs, but the rider will not drive. The transmission is in neutral. Depress the brake and move the shifter lever into a forward gear. The parking brake is engaged. Disengage the parking brake. The rider steers hard or handles poorly. Incorrect tire inflation. Refer to the Checking the Tire Pressure section. The mower cut is uneven. The tires are not correctly inflated. The mower cut looks rough. The engine stalls easily with the mower engaged.
11. Disposal Chassis Front Tire Size 15 in. x 6.00 in. - 6 in. Rear Tire Size 20 in. x 8.00 in. - 8 in. • Gasoline and oil are hazardous waste. Dispose of these materials properly. Front Tire Pressure 14 psi • Do not pour gas or oil into the ground or into household garbage. Contact your local recycling authority. Rear Tire Pressure 10 psi Turning Radius 18 in. • Some recycling centers will accept gas and oil and will recondition it or recycle it safely.
12. Warranty A. REGISTRATION: Please register your Murray MT100 lawn tractor within 60 days of the date of purchase. Go to dayenorthamerica.com/warranty to register. B. GENERAL PROVISIONS: The warranties described below are provided by Daye, North America, Inc. (“Manufacturer”) to the original purchaser of a new Murray MT100 lawn tractor (“Equipment”) from The Home Depot.
TRACTOR CORTACÉSPED MT100 Manual del Usuario Modelo #MYT4213500 Número de Atención al Cliente: 855-693-2582 | www.murray.
TABLA DE CONTENIDOS 1. Información General SECCIÓN 1 Información General ...............................3 Nivelar la Cubierta de Corte SECCIÓN 2 Seguridad del Operador.........................4 Quitar la Cubierta de Corte..........................28 Guarde Estas Instrucciones .............................4 Ajuste de la Tensión en la Correa de Cubierta ...29 Guía de Identificación de Pendientes ..............4 Cambiar la Correa de la Cubierta ..................
2. Seguridad del Operador Guarde Estas Instrucciones Guarde estas instrucciones para futuras referencias. Este manual contiene información de seguridad para hacerle conocer los peligros y riesgos asociados con el producto y cómo evitarlos. También contiene instrucciones importantes que deben obedecerse durante la instalación, operación y mantenimiento inicial del producto. Este producto está diseñado y destinado a cortar el césped bien cuidado y no está destinado a otros fines.
Instrucciones de Seguridad Calcomanías de Seguridad Los siguientes símbolos de seguridad aparecen en este producto. Antes de que opere el cortacésped, por favor, estúdielos y aprenda sus significados. IMPORTANTE: Si las calcomanías de seguridad se desgastan o dañan y no pueden ser leídas, ordene calcomanías de reemplazo de su centro de servicio autorizado. Símbolo Explicación Símbolo de alerta de seguridad • Sólo opere la máquina a la luz del día o con buena luz artificial.
Específico de la Pendiente ADVERTENCIA: Las pendientes son un factor importante relacionado con los accidentes. Operar la máquina en pendientes requiere precauciones adicionales. PELIGRO: Si está en reposo en una pendiente cuesta arriba, no cambie la velocidad del tractor y suelte el embrague. Hacer esto puede resultar en un revolcón hacia atrás (las ruedas delanteras se levantan del suelo y la máquina se da vuelta hacia atrás). • Viaje en la dirección recomendada por el fabricante en las pendientes.
Ensamblaje de la Cobertura del Tablero Ensamblaje del Aro del Conducto de Aire 1. Abra la cubierta del motor e instale el cobertor del tablero en su lugar. (Fig. 2) 1. Abra la cubierta del motor e instale el aro del conducto de aire adentro de la cubierta del motor. (Fig. 3) Ensamblaje del Volante 1. Alinee el volante con el eje de dirección, deslice el volante por el eje hasta que esté en su posición y asegure el volante con el tornillo proporcionado. (Fig.
Ensamblaje del Asiento Conectar la Batería 1. Conecte el asiento a la base del cortacésped con los tornillos y tuercas proporcionados. (Fig. 6) La batería se encuentra debajo del asiento del operador. Para conectar los cables de la batería, proceda de la siguiente manera: 2. Ajuste la posición del asiento para asegurar que usted pueda presionar completamente el pedal del freno antes de operar el tractor. 3. Conecte el interruptor del asiento. 1.
4. Funciones y Controles Encendido Los siguientes símbolos de control aparecen en este producto. Antes de que opere el cortacésped, por favor, estúdielos y aprenda sus significados.
5. Operando el Tractor Lea la sección de Seguridad del Operador antes de operar esta máquina. Asegúrese de conocer los controles y cómo detener la unidad. • Área de Funcionamiento • Conozca el área donde planea operar el tractor cortacésped. • Asegúrese de que el área esté libre de materiales no deseados que podrían ser recogidos por las cuchillas y arrojados. PELIGRO: Esta máquina es capaz de arrojar objetos que podrían lastimar a otras personas presentes o podría causar daños a construcciones.
Al Añadir Combustible 1. Put the unit on a level surface as shown in Fig. 11. Fig. 13 Recomendación de Combustible Fig. 11 El combustible debe cumplir con estos requisitos: 2. Apague el motor y saque la llave. Asegúrese de que el área de llenado de aceite esté limpia. • Gasolina limpia, fresca y sin plomo. 3. Remueva la varilla del aceite (Fig. 12 y Fig. 13). Limpie el resto del aceite de la varilla del aceite. 4. Coloque y apriete la varilla del aceite. 5.
Usar la Palanca del Acelerador/Estrangulador La palanca del acelerador/estrangulador se encuentra en el lado izquierdo del tablero de instrumentos del tractor cortacésped. Al encender el motor cuando está frío, empuje el acelerador totalmente hacia adelante hasta “ESTRANGULADOR” (CHOKE).(Fig. 15) El propósito del estrangulador es de restringir el flujo de aire para que la mezcla de combustible-aire sea más rica (más combustible, menos aire), lo que ayuda a encender el motor.
Ajustar las Ruedas Antideslizantes de Cubierta Presione el pedal de freno para bajar la velocidad del tractor cortacésped hasta frenarlo. (Fig. 18) AVISO: La parte de abajo de las ruedas antideslizantes de cubierta debe colocarse a aproximadamente 1/8 in. - 1/2 in. del suelo cuando el tractor esté a la altura de corte deseada. Esto va a disminuir la probabilidad de arrancar el césped en la mayoría de los casos. • Detenga las cuchillas al cruzar superficies de gravilla.
6. Mantenimiento Opción de Cortar el Césped en Reversa (MIR) Antes de los ajustes y reparaciones: PELIGRO: Cortar el césped en reversa puede ser peligroso para las personas presentes. Pueden ocurrir accidentes trágicos si el usuario no está alerta a la presencia de los niños. Los niños usualmente se sienten atraídos por la máquina y la actividad de cortar el césped. Nunca asuma que los niños permanecerán donde los vio por última vez. • Use SÓLO las herramientas correctas.
MOTOR Primeras 5 horas Cambie el aceite del motor. Cada 8 horas o a diario Cambie el nivel del aceite del motor. Cada 25 horas o anualmente* Limpie el filtro de aire. Cada 50 horas o anualmente* Cambie el aceite del motor. Anualmente Reemplace el filtro de aire. Vea a un Centro de Servicio Autorizado Anualmente AVISO: Si levanta el lado, usted necesitará girar la tuerca de ajuste de arriba primero. Si lo baja, gire la tuerca de abajo primero.
5. Sin mover la tuerca de ajuste interna, vuelva a apretar la tuerca de seguridad externa para asegurar la tuerca de ajuste interna en su lugar. (Fig. 25) 7. Deslice la cubierta hacia afuera desde debajo del tractor. 8. Revierta el proceso para volver a conectar la cubierta al tractor. Cambiar la Correa de la Cubierta Ajuste de la Tensión en la Correa de Cubierta Si nota un deterioro en el rendimiento de corte, puede ser necesario ajustar la tensión en el cable de cubierta.
Cambiar la Correa de Transmisión ADVERTENCIA: Apague el motor, ponga el freno de mano y retire la llave. ADVERTENCIA: De ser necesario, eleve el tractor con un gato y soportes de gato. Asegúrese de que el tractor esté debidamente protegido y que el freno de mano esté colocado antes de continuar. No asegurar debidamente el tractor podría hacer que se caiga, resultando en la muerte o una posible lesión personal grave.
a Revisar el Tiempo de Parada de las Cuchillas del Tractor Cortacésped c 3. Coloque la manga del drenaje de aceite (incluida con el tractor cortacésped) debajo del tapón de drenaje. (Fig. 35) 4. Coloque un recipiente de recolección debajo de la manga del drenaje de aceite. 5. Retire el tapón de drenaje. 6. Después de que el aceite se haya drenado, vuelva a colocar el tapón de drenaje firmemente. b ADVERTENCIA: Si la cuchilla del motor no se DETIENE en 5 segundos o menos, se debe ajustar el embrague.
Cambiar el Filtro de Aire ADVERTENCIA: NO encienda u opere el motor sin un filtro de aire ya que es un riesgo de incendio. AVISO: NO use aire presurizado o disolventes para limpiar el filtro de aire. El aire presurizado puede dañar el filtro y los disolventes lo van a disolver. Revisar las Bujías ADVERTENCIA: Las chipas involuntarias pueden causar un incendio o descarga eléctrica. El arranque involuntario puede causar enredos, amputaciones traumáticas o laceraciones. 2. Retire el filtro de aire. 3.
7. Transporte • Vacíe el tanque de combustible con una bomba aspirante antes de transportar la máquina. Encienda el motor y deje que corra hasta que haya usado toda la gasolina restante. • Cierre el tapón de combustible firmemente. • Deje que el motor se enfríe antes de transportarlo. 8. Almacenamiento Sistema de Combustible • Tenga mucho cuidado al cargar o descargar la máquina en un remolque o camión.
9. Solución de Problemas El motor corre, pero no se deja manejar. ADVERTENCIA: Antes de realizar cualquier tipo de mantenimiento, desactive todos los controles y apague el motor. Espere hasta que las partes móviles se detengan por completo. Desconecte el cable de la bujía y colóquelo contra el motor para prevenir un arranque no deseado. Siempre use gafas de seguridad al operar la máquina o al realizar cualquier ajuste o reparación.
10. Especificaciones Chasis Tabla de Especificaciones MODELO DEL TRACTOR MT100 Motor 15 in. x 6.00 in. - 6 in. Tamaño de Las Ruedas Traseras 20 in. x 8.00 in. - 8 in. Presión de Las Ruedas Delanteras 14 psi Presión de Las Ruedas Traseras 10 psi Radio de Giro 18 in. Sistema Eléctrico Modelo Briggs & Stratton E1350 Cilindrada 30.5 in3 (500 cc) Fusible 20 Amp Potencia 13.
11. Desecho 12. Garantía • La gasolina y el aceite son un desecho peligroso. Deshágase de estos materiales correctamente. A. REGISTRO: Por favor registre su tractor cortacésped Murray MT100 en un plazo de 60 días a partir de la fecha de compra. Diríjase a dayenorthamerica.com/warranty para registrarse. • No vierta gasolina o aceite en el suelo o en la basura doméstica. Contacte a su autoridad local de reciclaje.