Please read this manual carefully before installation and keep it for future reference. Owner & Installation Manual Water Dispenser Models: MTW04RO|MTW04UF Please read this manual carefully before installation and keep it for future reference. V04.10.
Contents 1 Product Summary .............................................................................2 2 General Information..........................................................................3 3 How to Install......................................................................................5 4 How to Use...........................................................................................7 5 Troubleshooting..........................................................................
Product Summary To Our Customers 1 Thank you for choosing the MRCOOL® Water Dispenser. In order to use and maintain this product correctly, please read the manual carefully before using the product. Store the manual for future reference. (1) This is a vertical water dispenser, please place it on the ground firmly to avoid falling. (2) Operation conditions: Water source: municipal tap water, Feed water pressure: 0.1 MPa ~ 0.
General Information 2 Technical Parameters Model Number MTW04RO / MTW04UF Feed Water Municipal tap water Voltage and Frequency 110/220V, 50/60HZ Rated Power 665W Heating Power 500W Cooling Power 150W Water Production Power 15W Inlet Water Pressure 14.5 to 58 PSI (0.1MPa ~ 0.4MPa) Inlet Water Temperature 41-100°F (5-38°C) Purified Water Flow 0.4L/min(RO) / 2L/min (UF) Dimensions W - 1.3Ft (387mm) * D - 1.5Ft (462mm) * H - 4.
General Information Filters and Their Functions (Model MTW04RO only) mrcool.
How To Install 3 Installation Procedures (1) Tools Required: •Phillips (cross-tip) screw driver •Adjustable wrench •Scissors (2) Review the Packing List to ensure all items are included in the packaging. (3) Installation Position Required: •Close to 220V /11OV socket •Close to tap water source •Close to drain outlet, please note that the position of drain pipes should be at least 20cm lower than water pan.
How To Install (6) Install Drain Clamp (For Model MTW04RO only) • Position drain clamp on drain pipe above the drain trap and ti ghten securely. • Using the drain clamp as a guide, drill a 6mm hole, enough for the 1/4" tubing to pass, through one side of the drain pipe. DO NOT drill through both sides. NOTE When cutting the tubing make clean, square, cuts, failing to do so result in poor connection and possible leaks.
How To Use How To Get Hot Water 4 1. Flip the heating switch on (switch position will be from "O" to "-".), the machine will start heating. 2. Press the hot water button on the control panel. After a short "Ding" sound, the hot water status is released and will last for 3 seconds. 3. Press the "water Outlet/ Ambient Water button" within 3 seconds and you will get hot water (a red circling light will appear around the "water outlet" button ). 4.
How to Use How To Get Cold Water 1. Press the Cooling switch on (switch position will be from "O" to "-”), the machine will start cooling. 2. Press the cold water button on the control panel. A "Ding” sound will signal the cold water status is released and will last for 3 seconds. 3. Press the "water Outlet/ Ambient Water button" within 3 seconds and you will get cold water (a blue light will circle around the "water outlet" button ). 4.
How to Use Service Life of Filter Cartridges and Filter Change Reminder NOTE The service life in the follow tables is calculated when the machine is in the process of pure water production. Page 9 mrcool.
How to Use Filter Life Reset Press the corresponding light indicator and hold for 3 seconds or more. Three chimes will sound notifying the filter life reset is completed. mrcool.
Troubleshooting Page 11 mrcool.
Light Indicator mrcool.
Water Dispenser Models: MTW04RO|MTW04UF The design and specifications of this product and/or manual are subject to change without prior notice. Consult with the sales agency or manufacturer for details.
