GPS INSTALLATION & USER GUIDE Compatible with the following controllers TV Nomad 3 Nomad SD/SD2 ALL RIGHTS RESERVED Internet MESA Rev 03.25.
INDEX BILL OF MATERIALS Components for configuration 3 BLOCK DIAGRAM OF INSTALLATION 4 CONTROLLERS Rear View and Definitions 5 OPERATION TV MESA 6 7 GPS OPERATION 8 INSTALLATION TIPS /ERROR CODES 9 INSTALLATION PICTURES 10 GPS WIRING DIAGRAM 11 CONTACT INFORMATION 12 2
Components For GPS Assembly 1 2 3 Pictures 1. How the GPS Assembly is shipped. 2. Components that go into a GPS Kit. (Mounting Bracket, GPS Module (PC Board) 3. Splitter (voltage passing from the single port side through to the dual port side) Part Number 213-GPS-002 GPS Kit Kit Includes 1 ea. 413-GPS-002 1 ea. 339-HFS2P 1 ea.
GPS LAYOUT For use with NOMAD 3, SD/SD2 or MESA Controllers ONLY Note: For TV - Nomad 3 Software version 37.6 and Nomad SD/SD2 Version 27 (or greater) is required. MESA GPS Module To Satellite receiver or Modem TV To Satellite receiver or Modem Use any connection To LNB except noted below. Note: When using the DP-3 Dish Splitter st Network LNB the 1 connection on the left (coded white) can only be used for External Dish “IN”. It is not an “output” from LNB” connection.
Nomad 3, SD, SD2 or MESA REAR VIEW 12 VDC or 15 VDC Control Cable (Optional with the MESA) To TV Receiver Or Internet Modem To TV Mount or Internet LNB The Rear Panel consists of a plug in connections Main Power and Motor Control Cable (optional with the MESA) and F-Connectors To TV Receiver or Internet Modem and To TV Mount or Internet LNB. CONNECTIONS DC Voltage: This connection provides the +12 or +15 volt DC input power to the controller.
OPERATION The following is a basic operation of the Nomad Controllers and is meant to get the system up and running in a short period of time. TV POWER UP Nomad 3 After making all the proper connections of the Nomad 3 Controller to the system, turn ON the power using the POWER button. The unit will begin to do a self test routine. This will take a few seconds.
MESA GPS Operation MESA Controller After making all the proper connections to the MESA Controller, turn ON the power using the POWER button. The unit will begin internal self checks. One of those checks will be to see if it has a valid GPS read. This could take a few minutes. • When power is first applied to the MESA Controller it will immediately begin to acquire GPS satellites.
TV GPS Operation Nomad 3 The GPS can receive its power from the satellite receiver. It can also receive power from the Nomad 3 controller. To receive power from the satellite receiver it must be plugged in and sending power to the GPS by way of the Nomad 3 Controller in order for the GPS to receive satellite coordinates. Note: the Nomad Controller does not have to be powered on.
INSTALLATION TIPS When installing the GPS Module to work with your TV or MESA system it must be placed in a location that can give it an unobstructed view of the sky. DO NOT • Do not place the GPS Module under the dish or any object that can block the GPS signal reception from the satellites. • Do not place in a location subject to standing water. • Do not install the splitter where water damage could occur. DO • • • Protect all outside coax connections from moisture using a form of dielectric grease.
Sample TV Installation 10
GPS WIRING DIAGRAM MESA Mount GPS TV Mount This splitter is Voltage passing ONE WAY Splitter In from LNB CONTROLLER 11
For additional information at this time contact MotoSAT Technical Support @ 800-247-7486 Thank you for your assistance, Your Friends at MotoSAT MotoSAT 1955 South Milestone Dr. Salt Lake City, UT 84104 Tele 800-247-7486 Fax 801-972-5407 www.motosat.
