~8214842.doc Synergy® V Universal / DVR Remote Control Model RC-U63CDR Programming And Operating Instructions (Part # 9-542-906) © 2007, Contec Holdings, LLC, Rev.
~8214842.doc 1. Introduction ® Your Synergy V Universal / DVR remote control is simple to program, easy to use, and can operate up to five (5) electronic devices, which include: CABLE TV VCR DVD AUDIO Cable set-top terminals Televisions VCR DVD Audio receivers, amplifiers, CD players Before you can use your remote control, it must be programmed (set-up) to operate the above devices. 2.
~8214842.doc 2. From the Cable Setup Code list, locate the 3-digit code for your brand / model and enter it on the keypad of the remote control. The set-top terminal will turn off. 3. Then, press [OK] to lock in the code. The power / mode buttons will blink 3-times and go out.
~8214842.doc ® Point and Press Programming This method allows you to program the remote control without using codes. Instead, the remote control automatically finds the correct command that you select in a variety of codes until you find the code that operates your device. You then lock in the correct code as described below. The following instructions describe how to program your remote control using the [CH +] or [CH -] buttons ("Power" function during programming).
~8214842.doc 2. Next, program your remote to operate the TV functions of your combination device. Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates the TV functions (Power, Vol +/-, Mute) of your combination device. 3. Last, program your remote to operate the VCR functions of your combination device.
~8214842.
~8214842.
~8214842.
~8214842.
~8214842.
~8214842.doc Luxman Magnavox Marantz NAD Onkyo Optimus Panasonic Parasound Philips (Magnavox) Pioneer Quasar Radio Shack RCA Realistic Rotel Sansui Sanyo Scott Sharp Sherwood Sony Soundesign SSI Taekwang Teac Technics Wards Victor Yamaha Zenith 8.
~8214842.doc [0] - Turns on / off CBL + TV (default setting) [1] - Turns on / off CBL + TV and tunes TV to output Channel 3. [2] - Turns on / off CBL + TV and tunes TV to output Channel 2. [3] - Turns on / off CBL + TV and tunes TV to output Channel 4. [10] - Turns on / off CBL + TV + VCR + DVD [4] - Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 3. [5] - Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 2.
~8214842.doc 2. Enter each channel as follows (ex. assumes 4-digit channel format): a. b. c. d. e. f. g. h. i. st Enter 1 channel # - 0001. Press [CH +] to advance to nd Enter 2 channel # - 0012. Press [CH +] to advance to rd Enter 3 channel # - 0123. Press [CH +] to advance to th Enter 4 channel # - 1234. Press [CH +] to advance to th Enter 5 channel # - 0017. next channel # setting. next channel # setting. next channel # setting. next channel # setting. 3.
~8214842.doc To reset your remote to its factory default settings, follow these steps: 1. Press [CBL], then [OK] together until the [CBL] button illuminates. 2. Press [1]. The [CBL] button will blink 3 times and go out. Reset returns all programmable features to their factory default settings. 14. Additional Programming Information, Troubleshooting, Terms Additional Programming Information 1. The power / mode buttons will illuminate in slow-rotation (i.e.
~8214842.doc When this occurs, replace the existing batteries with two (2) new AA Alkaline batteries to restore normal operation to the remote. If your remote still does not operate, you may want to check to see if one of the buttons is stuck in its “down” position. 3. If you have a TV that’s operated by remote control, it is recommended that you plug it directly into a wall outlet instead of the cable set-top terminal. 4.
~8214842.doc ® 15. Using Your Synergy V - Universal / DVR Remote Control Important: The following diagram shows how to use the buttons on your remote control to operate the DVR and PIP functions of the Motorola DCT series DVR set-top terminals. To access these functions, set the remote control to its Cable mode by pressing the [MODE] button, followed by the [CBL] button. Mode - Illuminates / select electronic device being operated.
