AP 7161 ACCESS POINT INSTALLATION GUIDE
AP 7161 Access Point Installation Guide
AP 7161 Access Point Installation Guide 3 Motorola Solutions reserves the right to make changes to any product to improve reliability, function, or design. Motorola Solutions does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
AP 7161 Access Point Installation Guide Introduction............................................................................................................................................ 6 Document Conventions........................................................................................................................ 8 AP 7161 Hardware................................................................................................................................. 8 AP 7161 Antennas......
AP 7161 Access Point Installation Guide 5 Warnings for the Use of Wireless Devices...................................................................................... 37 Potentially Hazardous Atmospheres............................................................................................... 37 Safety in Hospitals.......................................................................................................................... 37 RF Exposure Guidelines.......................................
AP 7161 Access Point Installation Guide Introduction Perfect for extending network coverage to outside areas, the AP 7161 brings the latest 802.11n 3x3 Multiple Input Multiple Output (MIMO) tri-radio design together with rugged outdoor performance. True perimeter security is provided using either a dedicated dual band sensor or software mode for both 2.4GHz and 5GHz bands to deliver 24x7 rogue detection and termination.
AP 7161 Access Point Installation Guide Document Conventions The following graphical alerts are used in this document to indicate notable situations: NOTE ! Tips, hints, or special requirements that you should take note of. CAUTION WARNING! Care is required. Disregarding a caution can result in data loss or equipment malfunction. Indicates a condition or procedure that could result in personal injury or equipment damage.
AP 7161 Access Point Installation Guide AP 7161 Hardware There are currently four models of the AP 7161 access point. Model Number Description AP-7161-66040-US AP 7161 outdoor 802.11N AP US AP-7161-66040-WR AP 7161 outdoor 802.11N AP International AP-7161-66S40-US AP 7161 outdoor 802.11N AP with sensor US AP-7161-66S40-WR AP 7161 outdoor 802.11N AP with sensor International AP 7161 Antennas The AP 7161 antenna suite includes the following options: AP 7161 2.
AP 7161 Access Point Installation Guide 9 Hardware Accessories Hardware accessories for the AP 7161 access point that can be ordered include a Power over Ethernet (PoE) unit and mounting hardware. PoE Accessories Hardware Accessory Part Number IP66 802.3at gigabit Ethernet power injector 100-240VAC US AP-PSBIAS-7161-US IP66 802.
AP 7161 Access Point Installation Guide Package Contents Carefully remove all protective packing material from around the AP 7161 access point and save the container for later storage and shipping. Refer to AP 7161 Hardware on page 8 when verifying receipt of all hardware a accessory items which should be included in your order.
AP 7161 Access Point Installation Guide 11 • Verify that the deployment environment has a continuous temperature range compatible with the operating temperature range of the device. Warnings • Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the access point to its power source. • Remove jewelry and watches before installing this equipment. • Verify that the unit is grounded before connecting it to the power source.
AP 7161 Access Point Installation Guide Access Point Placement Observe the following recommended guidelines to help ensure a successful network deployment: • Identify all pieces of the mounting bracket and mounting extension arm hardware and ancillary hardware (see AP 7161 Hardware on page 8 ). • Mount the device with the black gore vent down. • Mounting height for network devices should not exceed 30 to 35 feet.
AP 7161 Access Point Installation Guide 13 AP 7161 Hardware Installation The AP 7161 access point has the following port designations: • GE1/POE - LAN Port • GE2 - WAN Port • Console Port An AP 7161 must be installed by trained professionals familiar with RF planning and regulatory limits defined by the regulatory bodies of the country where the devices are being deployed.
AP 7161 Access Point Installation Guide The optional dual band antenna can be mounted on the connectors marked R3-A and R3-B. WARNING! Antenna ports where no antenna is mounted must be properly terminated using an approved IP67 terminator. AP 7161 Antenna Options The AP 7161 access point supports options for 2.4 GHz, 5 GHz, and a dual band antenna. The AP 7161 can be purchased in a three radio configuration.
AP 7161 Access Point Installation Guide 15 AP 7161 Console, GE1/POE and GE2 Ports The AP 7161 has Ethernet ports for external Console, GE1/POE, and GE2 connections.To gain access to the ports you will need to remove the protective caps. The Ethernet cable from the PoE device (if used) connects to the GE1/POE port on the unit. The GE2 port on the unit can be used if a second data connection for an external device (e.g. surveillance camera) is required.
AP 7161 Access Point Installation Guide AP 7161 Grounding Screw The grounding screw is located to the right of the GE1/POE port and above the GND symbol. WARNING! The grounding cable for an AP 7161 must be a #10 gauge wire cross section. The grounding cable can be attached to the unit using one of three recommended methods. Using an 8mm socket and driver: • Loosen the grounding screw and insert the grounding cable into the hole below it. Tighten the grounding screw to between 21.9 and 29.
AP 7161 Access Point Installation Guide 17 LED Indicators The AP 7161 access point has six LEDs on the top of the access point housing. The access point utilizes two different colored lights below each LED. Only one light displays within an LED at any given time. Every light within each LED is exercised during startup to allow the user to see if an LED is not functioning. The LEDs turn on and off while rotating in a circular pattern.
AP 7161 Access Point Installation Guide The top housing LEDs have the following display and functionality: Three Radio LEDs A three radio access point with sensor (P/N AP-7161-66S40-US and AP-7161-66S40-WR) has the following unique LED behavior: LED 1 (Sensor) LED 2 (2.4 GHz) LED 3 (5 GHz) LED 4 (GE2/WAN) LED 5 (GE1/LAN) LED 6 (System) Blinking Emerald and Amber at 2 second interval indicates a radio is present but not connected to a server. Blinking Emerald indicates 802.11b/g/n activity.
AP 7161 Access Point Installation Guide 19 Dual Radio LEDs A dual radio model access point (P/N AP-7161-66040-US and AP-7161-66040-WR) has the following unique LED behavior: LED 1 (Sensor) Not Used LED 2 (2.4 GHz) LED 3 (5 GHz) LED 4 (GE2/WAN) LED 5 (GE1/LAN) Blinking Emerald indicates 802.11b/g/n activity. Blinking Amber indicates 802.11a/n activity. LED Off indicates the port is not connected. LED Off indicates the port is not connected. Solid Red indicates diagnostic mode.
AP 7161 Access Point Installation Guide Installing an AP 7161 The following procedures detail the installation procedure for deploying an AP 7161 access point: Required Tools The following is a list of the minimal tool set required to install an AP 7161: • 8 mm socket and driver (for ground screw) • #2 phillips screwdriver (for external hardware reset cover screw) • Torque wrench or ratchet with 10mm, 1/2 inch and 3/4 inch sockets (for U-bolt, 1/2 inch and 3/4 inch bolts and nuts) • Adjustable wrench
AP 7161 Access Point Installation Guide 21 Assembly of the complete mounting hardware kit is shown below. Extension Arm When mounting an AP 7161 on poles more than 3 inches in diameter, a minimum standoff distance of twelve inches is required to avoid interference with the antennas. The extension arm for the mounting kit (P/N KT-150173-01) can be used alone, or when required, in combination with parts of the mounting hardware kit.
AP 7161 Access Point Installation Guide Ancillary hardware to attach the extension arm to the mounting hardware kit sections is included in the extension arm kit. Description Quantity 1/2 inch hex head nut 2 1/2 inch x 3/4 inch hex head bolt 2 Pole Mounted Installations The mounting hardware kit and extension arm can be used in various combinations to properly install the AP 7161 on a pole.
AP 7161 Access Point Installation Guide 23 Vertical Pole Mount Use the following procedures for vertical pole mount installations. Use of the extension arm is recommended when mounting the access point to poles greater than 3 inches is diameter. For poles up to 3 inches in diameter: 1. Thread the two inner nuts onto the U-bolt. Place the U-bolt at the desired mounting location. 2. Place the pole mount bracket section on the U bolt.
AP 7161 Access Point Installation Guide 11. To adjust the position of the access point, rotate the access point bracket section (plus or minus 15 degrees) and tilt the angle adapter bracket section (up to 45 degrees). 12. Tighten all hex flange screws to 60 inch pounds (lbf-in). For poles greater than 3 inches in diameter: 1. Attach the pole mount bracket section at the desired mounting location using band clamps. 2.
AP 7161 Access Point Installation Guide 25 6. Rotate the access point bracket section upward and align the top holes on the sides with the top holes on the angle adapter bracket section. Insert two M6 hex flange screws into the top holes on the angle adapter bracket section. 7.
AP 7161 Access Point Installation Guide Wall Mounted Installations For wall mounted installations, use only the access point and the angle adjust bracket sections. The lag bolts are not included in the mounting bracket kits. ! CAUTION Always mount the AP 7161 with the black gore vent facing down. 1. With the open slot connections facing down, attach the angle adjust bracket section at the desired mounting location using four #10/32 lag bolts. 2.
AP 7161 Access Point Installation Guide 27 5. Use a torque wrench or a ratchet and a 10mm socket to finish attaching the angle adapter bracket section to the access point bracket section with the four M6 hex flange screws in the open slot connections and the top holes on the angle adapter bracket section. Do not tighten the screws until all rotation and tilt adjustments are complete 6.
AP 7161 Access Point Installation Guide Installing the Power Over Ethernet (PoE) Unit Optionally, the AP 7161 access point can be powered by a standalone gigabit PoE injector or from a Motorola Solutions LAN controller. A standard CAT5E cable can be used to provide the connection. When connecting to the GE1/POE port on the AP 7161, you must use the weatherproof RJ45 plug kit that comes with the unit and it must be properly installed to maintain a weatherproof seal.
AP 7161 Access Point Installation Guide 29 PoE Unit Specifications Parameter Description Input voltage 100-240 VAC (50-60 Hz) Input current 1 ampere (maximum) Maximum available output power 30 Watts Nominal output voltage 54 to 57 VDC Operating voltage 48 VDC (compatible with PoE .3af/.3at Draft) Operating temperature -40 to -55 degrees C / -40 to 131 degrees F for 30 Watts -40 to -65 degrees C / -40 to 149 degrees F for 15.
AP 7161 Access Point Installation Guide Installing the PoE Unit ! CAUTION The maximum length allowed for the PoE cables is 100 meters. To install the PoE unit: 1. Using the mounting hardware provided, mount the unit as required for an AP 7161 pole or wall mount installation. 2. Connect the earth ground cable to the unit and properly connect the cable to an external ground. 3. Connect the PoE unit LINE AC port to a 100-240 VAC outlet. 4. Connect the network LAN cable to the DATA IN port. 5.
AP 7161 Access Point Installation Guide 31 When connecting Ethernet cable from the DATA PWR OUT port on the PoE unit to the AP 7161 GE1/POE port, a properly rated RJ45 connector is required. One Weatherproof RJ45 plug kit is provided with each access point. When connecting cables to the AP 7161 Ethernet ports, follow the instructions in the connector packaging and tighten the connectors to create a weatherproof seal. Shielded cables are required.
AP 7161 Access Point Installation Guide Basic AP 7161 Configuration The AP 7161 access point receives its configuration once adopted by a Motorola Solutions RFS4000, RFS6000 or RFS7000 series controller. There are no required initial configuration settings beyond verifying power and LED functionality for the access point.
AP 7161 Access Point Installation Guide Specifications Hardware Specifications Operating Voltage 36-57 VDC Operating Current Not to exceed 750 mA@48 VDC Power In (PoE) PoE support inbound power - 802.3AT on GE1/POE port Dimensions (unit) mounted 28.1cm W x 21.8cx H x 9.4cm D (11.1" W x 8.6" H x 3.7" D) Weight (Unit) 6.4 lbs / 2.
AP 7161 Access Point Installation Guide Radio Specifications Network Standards IEEE 802.11 a/b/g/n, 802.11e, 802.11i, WPA2, WMM, and WMM-UAPSD Supported Data Rules 802.11b/g :1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 802.11a : 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 802.11n: MCS 0-15 up to 300 Mbps 802.11n Support 3x3 MIMO with 2 spatial streams 20MHz and 40MHz channels supported 300Mbps data rates per radio Packet aggregation (AMSDU,AMPDU) Reduced interframe spacing 802.
AP 7161 Access Point Installation Guide Optional Accessories • Mounting kit • Extension arm for mounting kit • IP66 outdoor rated 802.3AT power injector • Mounting kit for outdoor IP 66 802.
AP 7161 Access Point Installation Guide Basic Troubleshooting Basic troubleshooting recommendations for the AP 7161 access point are listed in the following table: Indication Response LEDs are not lit No power to device: • Verify 802.
AP 7161 Access Point Installation Guide 37 Regulatory Compliance This device is approved under the Symbol Technologies, Inc. brand. Symbol Technologies, Inc. is a wholly owned subsidiary of Motorola Solutions, Inc. (collectively “Motorola”). All Motorola Solutions devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
AP 7161 Access Point Installation Guide RF Exposure Guidelines Safety Information The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. Reduce RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied.
AP 7161 Access Point Installation Guide 39 Radio Frequency Interference Requirements - Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Devices using the 5.470 – 5.725 GHz band shall not be capable of transmitting in the 5.60-5.65 GHz band in Canada, make sure that Canada is the country selected during setup to ensure compliance.
AP 7161 Access Point Installation Guide Other Countries Australia Use of 5 GHz RLAN’s in Australia is restricted in the following band: 5.50 – 5.65 GHz. Brazil Regulatory Declarations for AP 7161 - BRAZIL Note: The certification mark applied to the AP 7161 is for Restrict Radiation Equipment. This equipment operates on a secondary basis and does not have the right for protection against harmful interference from other users including same equipment types.
AP 7161 Access Point Installation Guide Wireless device operates in the frequency band of 5.25-5.35 GHz, limited for indoor use only. 在 5.25-5.
AP 7161 Access Point Installation Guide Waste Electrical and Electronic WEEE
AP 7161 Access Point Installation Guide 43
AP 7161 Access Point Installation Guide Motorola Solutions Support Center If you have a problem with your equipment, contact support for your region. Contact information is available at: http://supportcentral.motorola.com/.
AP 7161 Access Point Installation Guide 45 AP 7161 Series ROHS Compliance 15 有毒有害物质或元素 部件名称 (Parts) 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 金属部件 (Metal Parts) X O O O O O 电路模块 (Circuit Modules) X O O O O O 电缆及电缆组件 (Cables and Cable Assemblies) X O O O O O 塑料和聚合物部件 (Plastic and Polymeric Parts) O O O O O O 光学和光学组件 (Optics and Optical Components) O O O O O O 电池 (Batteries) O O O O O O O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X
AP 7161 Access Point Installation Guide
AP 7161 Access Point Installation Guide 47
Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011 Motorola Solutions, Inc. All Rights Reserved.
