+ INSTALLATION CONDITION 1.Refer to the {Standard Part List) when unpacking , check all parts available . 2.Do not disassemble mixer body by yourself. 3.Connect inlet hoses to supply valves. 4.Make sure inlet pipes and supply valves have been installed and cleaned, also ensure no impurities in pipeline. 5. After installation , check all joints for leakages. snuggest don't fit the faucet in the severely corrosive environments.
+ PRODUCT LIST Waterfall XZ Music X2 LED X2 Rain Part mama ay No. Part name Tying. Part name City.
# INSTALLATION SHOWER SET SIZE & WATER PIPE LINE REFERENCE Step 1 Giver Head shower Unit: mm finch 3348 (Ad (140-50mn 21 {1200-1500mm) sie Parse refer to above for hy “or dimensions of shower stall reed 7 Ya Step 2 Over Heat hawser Unit: gingham fig K [1100-3300mm) Please refer fo above for height dimensions of shower installation.
+ INSTALLATION DEPTH OF MAIN BODY Unit: munchkin 1: Including the thickness of ceramic tile is less than or equal to the thickness of valve 3 3/4 98mm}, 50 the thickness of rite must be calculated before installation.
4+ MAIN BODY CONNECTING PIPE SCHEMATIC DIAGRAM I Warning:must install ht water and old water infer strictly as instructions. Wrap enough Teflon tape Hot water pipe 1.As shows in the figure, tha inlet and outlet pipes are per-buried pay attention fo the correct direction of installing fhe per-buried main body, and make sure that the mark level on tie top of the installation box is facing upward. uninstall the hot and cold water inlet pipes, Peshawar head and hand shower holder body jet pipes.
+ Shower head power/water pipe-layout Mt-sucker 110-2200 0/60: Install the power switch in the appropriate position by yourself Water pipes should be arranged according to the shower head function Inner rain] Waterfall: Shower head. two inlet pipes need to be laid out. Waterfall and Inner rain; + Shower head holes on ceiling aoe 518 Inside size aa .
+ Shower head intelligent exploded view (351 ED Power Supply Transformer input 1GO~240Y 50/60 Output 12/8A PE? 3 WiFi abrasive connector @ Shower head & Shower fixing screws > & Declarative Shaw Respectively to unscrew (Declarative screws, separate Decorative shower panel and @Shower head; Respectively to unscrew G Shower fixing screws. separate Shower head and? Stainless steel fix frame.
«+ Connect LED(signal line) + Testing the water Corrugated pi Shower Shower Receiver Testing the water’ LED(signal fins + Shower installation + Fix the decorative panel of shower Snowblower Fixing resews § Decorative sinister (Decorative screws are fitted with Shower hear Decorative shower panel Hawser fixing screws arg fitted vi
+ Touch remote use instruction: Main parameter: Panel controller Working Temp. Supply Voltage: DC-24v Size: LSU WIE H23mm 118416" 6/16" 14/18" Output: a Channel Output Current: beachhead chanson) Inaction mode common anode Touch Remote: Working voltage Emission current; 10mA Working Currant 300uA Standby Current: uA Standby time:6 mouths Control distance 20M Color putative point&d 1. Touch remote have 84 touch key.
+ USER MANUAL Mode: NO. FUNCTION REMOTE 1 Static red Brightness is adjustable 2 Static green Speed is nonadjustable 3 Baltic bite 4 Static purple 5 Slavic bite-grean 8 Silica yellow 7 Static white 8 RGB Jumping Brightness: 8 RG B Gradual Pee is adjustable 10 7-Colors Injuring 1 7-Colors Gradual Controller connections shown: LER proliferate Remarks: 1.This product should be commissioned and installed by qualified personal 2.This product can not be waterproof, need lo avoid sun and rain.
+ Body jet installation Spd Step 1.Wrap the threaded pipe of NPT1/2 with Teflon tape and screw it into the wall. Step 2.Cut off excess part with a saw. Step 3.Put on the decoration cap | then screw the massage shower in. + Install the hand shower holder Step 3 Step? Step Stept. Surew the thread into the water pipe inside the wail, Ste pd. Screw the main body into the thread. Step Rotate and fix the body with the special-shaped wrench.
Care and Maintenance in order to keep the mer surface bright, please clean the mixer regularly. Rinse faucet with clean water and wipe with soft colon cloth. Avoid suing cleaning powder , harsh cleaning chemicals, brushes,and cloth with coarse surface to prevent scratching and corrosion. Do not use acid cleaner to clean the faucet as it may cause surface corrosion of the faucet. If the faucet comes info contact with harmful acid substances, please rinse it with water immediately.
