Datasheet LW005-MP APP Configuration Guide MOKO TECHNOLOGY LTD. Version 1.0 www.mokosmart.
CONTENT 1 About this Manual............................................................................................................................. 3 2 MKLoRa APP ...................................................................................................................................... 3 2.1 Install MKLoRa APP................................................................................................................ 3 2.2 Connect to LW005-MP ..............................................
LW005-MP 1 About this Manual The purpose of this manual is to outline how to use MKLoRa APP for LW005-MP parameters configuration. 2 MKLoRa APP For the detailed operation of the MKLoRa app to configure and read device information, please refer to the following instructions: 2.1 Install MKLoRa APP User can get the APP download link by search“MKLoRa”in your phone APP store: Please allow Bluetooth to be enabled during the installation process.
LW005-MP The distance between the phone and the device should be kept within 10m without wall obstruction. Otherwise, the device will not be searched. After searching for the device, click the “CONNECT” to connect the device that you want to configure. Then you should enter the password, the default login password is “Moko4321”. Note: If a password is not entered within one minute, the login box will disappear, you should click “CONNECT” again.
LW005-MP LoRaWAN Status: Indicates the status of the LoRaWAN network connection. Connection Settings: Configure LoRaWAN network parameters. Application Settings: Configure LoRaWAN application parameters. 2.3.1.1 Connection Settings LoRaWAN Mode: LoRaWAN join-in mode selection DevEUI/AppEUI/AppKey: Network parameters in OTAA mode. 5 www.mokosmart.
LW005-MP DevEUI/AppEUI/DevAddr/AppKey/NwkSKey: Network parameters in ABP mode. Region/Subnet: Device frequency band selection, AS923/ AU915 /CN470 /CN779 /EU433 /EU868 /KR920 /IN865 /US915 /RU864 can be set. Device Type: LoRaWAN device mode; it can be set Class A or Class C, the default is Class C. Message Type: Uplink payload type, it can be set unconfirmed or confirmed, the default is confirmed. Advanced Setting: Some advanced parameter settings, if not necessary, it is not recommended to modify.
LW005-MP Time Sync Interval: It is used to sync the device time via MAC command. The default is 1, means that the device's time will be synchronized every 1 hour via LoRaWAN MAC commands. The value ranges from 0 -255H. 0 means disable. Network Check Interval: The device will periodically check the LoRaWAN network status via MAC command. The default is 1, means that the device will check the network status every 1 hour via LoRaWAN MAC commands. The value ranges from 0 -255H. 0 means disable. 2.3.
LW005-MP 2.3.2.2 Electricity Settings Report Interval: The report interval of electricity payloads. The default is 10, the unit is s. The value ranges from 5 -600s. 2.3.2.3 Energy Settings Report Interval: The report interval of energy payloads. The default is 1, the unit is minutes. The value ranges from 1 -60 minutes. It can’t be less than Energy Save Interval. Energy Save Interval: The save interval of energy data. The default is 1, the unit is minutes. The value ranges from 1 -60 minutes.
LW005-MP When the plug detects that the measured voltage/current/power exceeds the safe range for a period of time, it will automatically turn off the switch. The rated current and voltage of different plug types are not the same, so the power, voltage and current threshold configurations are also different, please set the threshold value according to the plug types.
LW005-MP UK plug: Default: 15.6, range: 0.1-15.6(unit: A) Time threshold Default: 4, range: 1-30 (unit: second) 2.3.2.5 Load Status Notification Load Status: The load status of LW005-MP. Load Start Notification: When the plug detects that the load starts working, it will immediately report a notification to the server. The default is ON. Load Stop Notification: When the plug detects that the load stops working, it will immediately report a notification to the server. The default is ON.
LW005-MP On this page, you can set the power indicator color and the function switch of the two indicators. The max power of different plug types isn’t the same, so the configuration ranges of the power indicator is also different, please set the measured power value according to the plug types.
LW005-MP ADV Name: The advertising name of the device, up to 16 characters. ADV Interval: Bluetooth advertising interval. The default is 1000ms. It ranges from 1-100, the unit is 100ms. Connectable: User can select the connectable state or the unconnectable state. The default is connectable state. When the device is on unconnectable state, the device only can be connected via Bluetooth in the first three minutes of power on.
LW005-MP DFU (Update Firmware): To update the firmware via the DFU should use the upgrade package that MOKO provides with ZIP format. If you use an android phone, place the ZIP file of firmware upgrade package into the phone folder, select the upgrade package file from the OTA page of the APP, and click to upgrade. If you use an iPhone, user need to share the upgrade package file with MKLoRa via computers and iTunes tools.
LW005-MP 3 Revision History Version Description Editor Date 1.0 Initial version Allen 14 2021-12-20 www.mokosmart.
LW005-MP MOKO TECHNOLOGY LTD. 4F,Buidling2, Guanghui Technology Park, MinQing Rd, Longhua, Shenzhen, Guangdong, China Tel:86-755-23573370-829 Support_lora@mokotechnology.com https://www.mokosmart.
