Assembly and Installation Guide READ THOROUGHLY BEFORE STARTING AND KEEP FOR FUTURE REFERENCE Rev B | 10/9/18 1 | Page
TA B L E O F C O N T E N T S 2 2 2 3 8 13 When Your Cabinets Arrive Tools You'll Need Before You Begin Base Cabinet Closet Overhead Cabinet 14 17 18 19 22 Instant Walls Installing Your Cabinets Countertop Brace Corner Filler Countertop WHEN YOUR CABINETS ARRIVE When your order is delivered, remove the packing material and thoroughly inspect all cabinets for damage.
BASE CABINET A 8-32 x 5/16” Flat Head Bolt w/ Nut (x8) B 10-24 x 3/8” Self Tapping Screw (x24) C 10-32 x 1” Pan Head Bolt w/ Nut (x8) D 1/4-20 x 1/2” Hex Bolt w/ Nut (x2) E Shim (1 sheet of 9) 1 Base Door Assembly (x1) 2 Base Side (x2) 3 Countertop Brace (x2) 4 Rear Brace (x2) 5 Shelf (x1) 6 Bottom Pan (x1) 7 Toe Kick Front (x1) 8 Toe Kick Side (x2) 9 Toe Kick Rear (x1) Rev B | 10/9/18 3 | Page
BASE CABINET B x2 4 B x2 2 3 B x2 B x4 B x2 4 3 1 Fo a m (Pa cki ng ma ter i al) Warning: When using a driver to install self-tapping screws, start at a low clutch setting and increase it incrementally until the screw turns. Reset your clutch each time you change batteries. Step 1 Step 2 Step 3 Step 4 Rev B | 10/9/18 1 on foam to protect it from scratches. Attach both Sides 2 to Door Assembly 1. (One side not shown for clarity) Attach Top Braces 3 to Sides 2.
BASE CABINET A A 8 7 9 Step 5 Attach the Toe Kick Front 7 to both Toe Kick Sides 8 . (One side not shown for clarity) Step 6 Attach Toe Kick Rear Rev B | 10/9/18 A x2 9 to Toe Kick Sides 8 .
BASE CABINET C x8 E Shims go here at installation Step 7 Put the Cabinet on the Toe Kick and attach loosely. During installation, add Rev B | 10/9/18 shim E between the Cabinet and Toe Kick to level the countertop.
BASE CABINET D x2 5 6 5 into place and attach to Door Frame. Shift the Bottom Pan 6 into slots in Toe Kick.
CLOSE T A 8-32 x 5/16” Flat Head Bolt w/ Nut (x8) B 10-24 x 3/8” Self Tapping Screw (x27) C 10-32 x 1” Pan Head Bolt w/ Nut (x8) D 1/4-20 x 1/2” Hex Bolt w/ Nut (x2) E Shim (1 sheet of 9) 1 Closet Door Assembly (x1) 2 Closet Side (x2) 3 Closet Top (x1) 4 Rear Brace (x1) 5 Shelf (x1) 6 Bottom Pan (x1) 7 Toe Kick Front (x1) 8 Toe Kick Side (x2) 9 Toe Kick Rear (x1) Rev B | 10/9/18 8 | Page
CLOSE T 3 B x11 2 B x6 B x2 4 1 Fo a m (Pa cki ng ma ter i al) Warning: When using a driver to install self-tapping screws, start at a low clutch setting and increase it incrementally until the screw turns. Reset your clutch each time you change batteries. Step 1 Step 2 Step 3 Step 4 Rev B | 10/9/18 1 on foam to protect it from scratches. Attach both Sides 2 to Door Assembly 1. (One side not shown for clarity) Attach Top 3 to Sides 2. Attach Rear Horizontal 4 to Sides 2.
CLOSE T A A 8 7 9 Step 5 Attach the Toe Kick Front 7 to both Toe Kick Sides 8 . (One side not shown for clarity) Step 6 Attach Toe Kick Rear Rev B | 10/9/18 A x2 9 to Toe Kick Sides 8 .
CLOSE T C x8 E Shims go here at installation Step 7 Put the Closet on the Toe Kick and attach loosely. During installation, add Rev B | 10/9/18 shim E between the Cabinet and Toe Kick.
CLOSE T D x2 5 6 5 into place and attach to Door Frame. Shift the Bottom Pan 6 into slots in Toe Kick.
OVERHEAD F E 10-32 x 3/8” Hex Bolt w/ Nut (x2) Shim (1 sheet of 9) 2 Light Shield (x1) 1 Overhead Cabinet (x1) 1 F x2 Step 1 Rev B | 10/9/18 Bolt the Light Shield 2 2 to the bottom of the Overhead cabinet 1 .
I N S TA N T WA L L S D 1/4-20 x 3/4” Hex Bolt w/ Nut F 1/4-20 Cage Nut 5 Short Corner Angles 3 Stiffener 4 Long Corner Angle 1 12" Instant Wall Panel 2 14" Instant Wall Panel 6 Wall Anchor Bracket For Mobile Toolboxes Rev B | 10/9/18 14 | Page
I N S TA N T WA L L Instant Wall panels come in two sizes: a 12" wide panel that will make up the majority of your Instant wall, and a 14" wide panel that is only used with Mobile Toolboxes. A x8 Step 1 Pair off Instant Wall panels of the same size. Bolt them together with a stiffener on both sides of the joint. Keep the tops of the panels flush when tightening the bolts. Step 2 Insert cage nuts in the back of each panel section.
ANCHOR BRACKETS Optional adjustable anchor brackets are provided for securing the Select Instant Wall to a wall for added stability. Anchor brackets can be adjusted, up to 10" long, to accomodate stem walls and other obstructions that prevent your cabinets from sitting flush against the wall. Step 1 Each bracket comes with a pre-formed offset end which fits inside the Instant Wall channel. Bend trim the other end to the desired length up to 4". Trim if necessary.
I N S TA L L I N G Y O U R C A B I N E T S Step 1 Put the first cabinet in place. Loosen the toe kick bolts to adjust the gap between the toe kick and cabinet sides and insert shims as necessary for leveling. We recommend that you level each cabinet as you go but only tightening the toe kick bolts after all the cabinets have been installed. Attach the cabinet to the Instant Walls with 1/4-20 bolts, or to your own walls with appropriate mounting hardware (not provided by Moduline).
COUNTERTOP BRACE D Step 1 Attach Countertop Brace to adjacent bases and/or toolboxes. D Step 2 If adjacent to a closet, use the Countertop Brace as a template to drill mounting holes in the Closet side. Make sure the Countertop Brace is level when drilling or marking holes.
CORNER FILLER C 10-32 x 1” Pan Head Bolt w/ Nut (x2) D 1/4-20 x 1/2” Hex Bolt w/ Nut (x6) E Shim (1 sheet of 9) 3 Countertop Brace (x1) 1 Corner Filler (x1) 4 Corner Countertop (x1) 2 Toe Kick Filler (x1) Rev B | 10/9/18 19 | Page
CORNER FILLER D x6 1 C x2 2 Step 1 Bolt the Corner Filler 1 and Toe Kick Filler 2 together. Step 2 Attach the assembled corner filler to adjacent bases and/or toolboxes. Step 3 Install bolts for the Countertop Brace Note: Leave all 1/4-20 bolts Rev B | 10/9/18 3 in the top-rear holes of the sides. D loose and tighten them at the end.
CORNER FILLER 3 Step 4 Slide Countertop Brace 3 down onto bolts in sides. Step 5 Tighten the bolts with the Countertop Brace level and flush with the tops of the adjacent cabinets. 3 Step 6 Drill holes in the Countertop Brace for wall mounting. Pre-punched holes are provided but you may need to drill your own to hit studs. Step 7 Secure the Countertop Brace to the wall with appropriate hardware (not Rev B | 10/9/18 provided). Wall-mounting screws shown for reference only.
COUNTERTOP Step 1 Apply double-sided tape to the tops of the base cabinets, toolboxes and countertop braces. Make sure to apply the tape across the entire front edge of the cabinets. DO NOT REMOVE THE TAPE BACKING Step 2 Before you remove the backing from the tape, test fit your countertops to make sure they fit correctly. Step 3 Remove the backing from the tape and thoroughly spray it with window cleaner. This allows you to adjust the countertop before it sets permanently.
Moduline Modular Aluminum Cabinets P.O. Box 339, West Bridgewater, MA USA 02379 Phone: 888-343-4463 | Fax: 508-580-5199 ModulineCabinets.
