AVIAT O R F L U SH FH- W1 8 1 1 - 5 4 s INSTALLATION INSTRUCTIONS WET DC MOTOR SMART works with the Google Assistant modernforms.
All Modern Forms Smart Fans are: WET SMART Durably finished and Rated for interior and exterior use Able to coordinate with smart devices for voice-activated and thermostat control Wet location-listed to the strictest ETL/cETL safety regulations DC MOTOR Quiet, reliable, and up to 70% more efficient than AC fans Wi-Fi and RF enabled for unlimited control APP INSTRUCTIONS AND SMART HOME DEVICE INTEGRATION modernforms.
TABLE OF CONTENTS 1. SAFETY RULES..............................................................................................................................................4 2. FTC ENERGY GUIDE & SPECIFICATION.....................................................................................................5 3. TOOLS AND MATERIALS REQUIRED..........................................................................................................5 4. PACKAGE CONTENTS.....................................
1. SAFETY RULES For operation, maintenance, and troubleshooting information, visit modernforms.com/help. 1. 2. 3. 4. 5. 6. 7. 8. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. box and ungrounded conductor on the other side of the outlet box. 9. All set screws must be checked and re-tightened where necessary before installation.
2. FTC ENERGY GUIDE & SPECIFICATION FAN FAN SIZE VOLTS N.W. (lbs) G.W. (lbs) STANDARD ELECTRICITY AIR FLOW ENERGY COSTS* FAN EFFICACY Aviator Flush 54” 120 6.85 10.67 High Speed 27W 6744 CFM $8/yr 246.1 CFM/W Weighted Average 15W 3982 CFM $4/yr 259 CFM/W * Estimated annual energy cost based on $0.12 per kWh and 6.4 hours use per day. 3.
4. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: REF. DESCRIPTION PART NO. A Blade Set of 3 RPL-F1811-54-BD-** B Blade Collector Ring --- C Hanger Plate RPL-F1811-HANGER-** D Hanger Gasket --- E Motor Assembly --- F Bottom Cap (Aluminum) --RPL-F1811-54-REC G Control Receiver w/ Hardware H Wall Control w/ Hardware F-WC-WT I Hardware Bag RPL-AVIATORFLUSH-PARTS 3/16” x .
4. PACKAGE CONTENTS (cont.) REF.
5. MOUNTING OPTIONS Joist If there isn’t an existing UL/cUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
6. INSTALLING THE MOUNTING BRACKET REMEMBER to turn off power at the breaker. Follow the steps below to hang your fan properly: 1. Disconnect power to the fan location at the breaker. A licensed electrician must install the fan. 2. There are four screws on top of the motor assembly. Remove two that are on the opposite of eachother and save for section 10. FIGURE 4 Loosen remaining two. 3. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 4. 4.
7. ATTACHING THE FAN BLADES 1. Blade Collector Ring Place blade on motor as shown in Fig 8 and secure with the blade attachment screws and washers. 2. Repeat this procedure with the remaining blades (Fig 8). 3. Secure the bottom of the blades together using the provided blade collector ring and hardware (Fig 9). 8. ATTACHING DECORATIVE LOWER CAP 1. Tightly twist the decorative lower cap onto the motor assembly (Fig 10).
9. MAKING THE ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. WARNING: Installation of this fan requires that a two-conductor cable with ground wire be run between ceiling and wall outlet box. WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.
9. MAKING THE ELECTRICAL CONNECTIONS (cont.) Motor to receiver electrical connections: (Fig. 10) Place motor on flat surface before connecting receiver wires. 1. MOTOR” from the receiver. 2. Connect the gray wire from the fan to the gray wire marked “TO MOTOR” from the receiver. 3. Connect the yellow wire from the fan to the yellow wire marked “TO MOTOR” from the receiver. 4. Connect the white wire from the fan to the white wire marked “For Light” from the receiver. 5.
9. MAKING THE ELECTRICAL CONNECTIONS (cont.) Receiver to house supply wires electrical connections: (Fig. 11 & 12) 1. FIGURE 11 Lift motor assembly and hang it using the cable / hook as shown in Figure 11. 2. Secure the safety cable to the building structure using a wood screw (Fig. 11). 3. Connect the fan assembly ground wire, mounting bracket ground wire and receiver ground wire to the ground wire in outlet box (Fig. 12).
10. FINISHING THE INSTALLATION 1. Secure all wire connections with supplied wire ties to assist in fan installation. 2. Tuck connections neatly into ceiling outlet box. 3. Remove the motor assembly from the hook on the mounting bracket. Position the motor up to the hanger plate and attach using two screws through the two key slots in the top of the motor housing (Fig. 13). Note: Make sure the receiver sits flat and does not interfere with the hook. 4.
11. INSTALLING THE LED LUMINAIRE MODULE (Optional Accessory) 1. CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing light kit. 1. Remove the three screws from the LED wire storage cap, keep the cap for future use when not using the luminaire (Fig. 14). 2. Install the LED mounting plate using 3 screws removed from step FIGURE 14 FIGURE 15 FIGURE 16 FIGURE 17 1 (Fig. 15). 3.
12. INSTALLING THE WALL CONTROL Wall control to wall outlet box electrical connections: (Fig. 19) 1. Connect the white wire from the control to the white (neutral) wire from the wall outlet box. 2. Connect the red wire form the control to the black wire from the wall outlet box that feeds up to the fan. 3. Connect the black wire marked “LINE IN” from the control to the black LINE VOLTAGE wire from the outlet box that feeds back to the main fuse box. 4.
12. INSTALLING THE WALL CONTROL (cont.) WARNING: Remember to shut the power off at the circuit breaker or fuse box. 1. Wall control Wall outlet box Wall mounting plate Carefully tuck the wire connections inside the junction box. Secure the wall control with the two wall transmitter screws provided (Fig. 20). 2. Attach the wall mounting plate over the wall switch and secure with the two wall mounting plate screws provided. 3. Fasten the wall plate to the wall mounting plate.
13. WALL CONTROL OPERATING INSTRUCTIONS Your DC brushless motor is equipped with an intuitive wall control. Restore power to ceiling fan and test the wall control as below for proper operation. Pairing the Wall Control to Your Fan Your fan is pre-paired at the factory, No pairing is necessary. Wall Control Button Definitions These seven buttons are used to set the fan speed as follows: Button: turn the light ON or OFF Press/Hold to increase the desired light level.
13. WALL CONTROL OPERATING INSTRUCTIONS (cont.) NOTE: A maximum of 2 fans can operate on a circuit through the wall control. NOTE: A maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the app for the fan control (without the wall control in the circuit). Summer Mode - (counter-clockwise) A downward airflow creates a cooling effect as shown in Fig. 26. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
14. APPLICATION In addition to the included wall control, you can control the fan through the Modern Forms app. 1. To use the app, download it for free from the App Store or Google Play. 2. Open the app to create your account. You can also log in with your FIGURE 24 FIGURE 25 Facebook or Google account. 3. Next, set up a WiFi connection. You’ll need the SSID and WiFi password for the network you want to connect to. 4.
15. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a signal. Please check power to wall control and all electrical connections. 3. Assure that there are no more than 2 fans operating on a circuit through the wall control.
16.
Español For instructions in Spanish please visit the link below. Para obtener instrucciones en español, visite el siguiente enlace. www.modernforms.com/fan-instructions-espanol Français For instructions in French please visit the link below. Pour obtenir des instructions en français, veuillez visiter le lien ci-dessous. www.modernforms.
Get Smart The Modern Forms app synchronizes seamlessly with smart home devices you already own. To learn more go to modernforms.com/mfappins works with the Google Assistant Free App Download Sync with our exclusive Modern Forms App to control fan speed, use smart features like Adaptive Learning, create groups and reduce energy costs. modernforms.
FH-W1811 25
FH -W1 811 26
FH-W1811 27
FH - W 1 8 1 1 modernforms.