Installation & Assembly

IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut o the power
at the circuit breaker and completely remove the old xture from the ceiling, including the old
mounting strap.
From the parts bag remove the mounting strap assembly. One end of nipple (F) should be
attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other end should
have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting
screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I) from canopy loop
(H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the
canopy loop’s exterior threads should be exposed, and the canopy loop collar should t snugly
onto the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H)
until the desired height is reached.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn o the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase.
FINISHING THE INSTALLATION
Push canopy (G), canopy mirror (G1) and canopy plate (G2) up to the ceiling. Slide canopy loop (H) and canopy loop collar (I) up beneath the canopy.
Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (G) in place.
Slide candle sleeves (Q) over the sockets. Install light bulbs (not provided) in accordance with the xture’s specications. Do not exceed the
maximum recommended wattage.
Your installation is complete. Turn on the power and test the xture.
ASSEMBLING THE FIXTURE
Place the xture’s base (R) on a at surface. Attach top loop (L) to
post (M) of top cap (N). One of connector rods (O) will house the
xture’s wires. Slide the xture’s wires through the rod and attach
hook (P) to loop (S). Hook the other end of the rod to top cap (N).
Pull the xture’s wires through the top of rod (O). Have an assistant
hold top cap (N) up and attach the remaining connector rods (O)
to xture’s base (R) and top cap (N). By measuring, determine the
correct number of chain links needed for proper hanging height. If
necessary, use a pair of pliers to open and remove any excess chain.
Attach chain connectors (K) to each end of chain (J) before attaching
one end of the chain connector/chain to top loop (L). Close the chain
connector. Connect the other chain connector (K) to canopy loop
(H). Feed the xture’s wires up through top loop (L) then through
chain (J) (every three links or so). Pull the wires until taut. Gently slide
canopy loop collar (I) and canopy plate (G2), canopy mirror (G1), and
canopy (G) onto the chain/wire.
CONNECTING THE WIRES
Have an assistant support the xture’s weight while completing the wiring. Cut away
excess wire. Thread the xture’s wires through canopy loop and nipple. Attach the
xture’s wires to the power supply wires from the junction box. Connect black to smooth/
black/transparent (L) wire; white to ribbed/white/transparent (N) wire; ground to ground
(green or copper). Twist the ends of the wire pairs together, and then twist on a wire
connector. Make sure all twists are in the same direction. If there is no ground wire (green
or copper) from the junction box, locate ground screw (E) on mounting strap (A) and
wrap the xture ground wire around the green ground screw (E). Use a screwdriver to
secure ground screw (E) onto the mounting bracket/mounting strap. Tuck all wires.
B
E
H
I
K
G
G1
G2
D
C
F
J
JUNCTION
BOX
L
M
N
Q
R
S
O
P
A
Assembly Instructions