User manual

Step
Step
Step
Step
Step
Attach the strap as shown.
Your camera uses one 3-volt CR123A or DL123A lithium
battery to supply power for all camera operations.
➀ Open the battery cover using a coin or
similar object.
➁ Insert the battery according to the + and –
marks inside the battery chamber and snap
the cover closed.
• Before removing an old battery, make sure the camera
is off.
If the blinking low-battery symbol appears in the
data panel with the other indicators, you can still
use the camera, but the battery will have to be
replaced soon.
If the blinking low-battery symbol appears alone
(date model: only the date/time display with the
blinking low-battery symbol), you cannot use the
camera until you replace the battery. The shutter
cannot be released.
Use only 35mm, DX-coded film rated ISO 25 to
3200. ISO 400 or higher is recommended for taking
telephoto photographs or pictures in low light.
• Do not use Polaroid instant 35mm film. Winding
problems may occur.
➀ Slide the back-cover release down to open
the back cover and place the film cartridge
into the film chamber.
• Always load and unload the film in subdued light.
➁ Extend the film tip to the “FILM TIP” mark,
making sure it lays flat.
➂ Close the back cover.
• The film automatically advances to the first frame and
appears in the data panel.
• If the film has been loaded improperly, will blink in the
data panel and the shutter will remain locked. Open the
back cover and repeat the loading procedure.
➀ Press the ON/OFF button to turn the
camera on.
• The flash will pop up and the lens barrel will extend.
• Press the ON/OFF button to turn the camera off.
• To conserve power, the camera automatically turns off if
it is not operated for more than eight minutes. The lens
barrel and flash will retract.
• Do not obstruct the lens while it is retracting.
FULL AUTO OPERATION - CONTINUED
➁ Look through the viewfinder and press the
W side of the zoom control to move toward
wide angle or the T side to move toward
telephoto.
• Do not hold the lens barrel; focus may not be accurate.
• Make sure your subject is at lease 0.4 m(16 in) from the
camera.
➂ Align your subject within the focus frame
and press the shutter-release button
partway down.
➃ When the green focus lamp glows, gently
press the shutter-release button all the way
down to take the picture.
• The flash will automatically fire in low light.
• The film automatically advances to the next frame.
Close-framing Guides
When your subject is closer than 1.2m (4 ft.) at
75mm, first lock focus on your subject by pressing
the shutter-release button partway down, then
recompose your picture within the close-framing
guides.
• If the green focus lamp blinks, your subject is closer
than the minimum focusing distance of 0.4m (16 in.) and
will not be in focus. The shutter cannot be released.
• If the subject is very close to the camera, the green
focus lamp will glow, but the picture will not be in focus.
When your subject is located outside the focus
frame, you can first lock focus on your subject, then
recompose the picture as desired.
➀ Align the subject within the focus frame and
press the shutter-release button partway
down until the green focus lamp glows.
The film will rewind automatically after the last
frame has been exposed.
When appears and blinks in the data panel,
open the back cover and remove the film.
To begin rewind before the end of the roll, turn the
camera on and gently press the rewind button
using a pen or similar object.
LOW BATTERY SYMBOL
CLOSE-FRAMING
➁ Without lifting your finger, recompose the
picture then press the shutter-release button
all the way down to take the picture.
FOCUS LOCK
MANUAL REWIND
If rewind stops before the film has been completely rewound and all indicators
blink, DO NOT OPEN THE BACK COVER. Insert a fresh battery then press the
rewind button.
ATTACHING THE STRAP
INSERTING THE BATTERY
LOADING THE FILM
FULL AUTO OPERATION
REWINDING THE FILM