M12 FDGA Original instructions
M12 FDGA Alkuperäiset ohjeet Algupärane kasutusjuhend Πρωτότυπο οδηγιών χρήσης Оригинальное руководство по эксплуатации Orijinal işletme talimatı Původním návodem k používání Оригинално ръководство за експлоатация Pôvodný návod na použitie Instrucţiuni de folosire originale Instrukcją oryginalną Оригинален прирачник за Eredeti használati utasítás работа Izvirna navodila Оригінал інструкції з Originalne pogonske upute експлуатації Instrukcijâm oriěinâlvalodâ Originali instrukcija ø 6 mm 2 15 ø 8 mm 17
I II III 15.000 10.000 20.000 4 24.
1. I Sd1 = Sd2 Sd2 Sd1 L3 = min. 10 mm Sd 1 Sd 2 D L3 L0 T 17 2. 15 L2 2 3.
4. I ø 8 mm 5. 17 15 6.
1. 2. 1. 2.
15.000 10.000 20.000 4 24.500 n ≤ nmax. MODE 1 2 3 4 n (min-1) 0-10 000 0-15 000 0-20 000 0-24 500 4 III 15.000 10.000 20.000 4 15.000 24.500 10.000 20.000 4 24.500 15.000 10.000 1 15.000 2 20.000 10.000 4 1 1 4 3 24.500 20.000 15.000 15.000 10.000 4 3 24.500 24.500 2 2 20.000 10.000 1 2 4 3 20.000 24.
25 % 1 6 50 % 75 % 100 % IV 4x <10 % Start 2 sec 2
Load-dependent motor protection: If the motor is overloaded, the overload protection will trip. To continue working, switch the machine off and then on again. If the battery becomes too hot, the fuel gauge lights will flash in an alternating pattern and the tool will not run. Allow the battery to cool down.
4 V 8
TECHNICAL DATA Fuel angled die grinder Production code M12 FDGA 4745 52 02... ...000001-999999 12 V 0-10000 / 0-15000 / 0-20000 / 0-24500 min-1 6,0 mm 8,0 mm 50 mm 0,7... 1,0 kg -18°C ... +50°C M12B... C12C; M12C4; M12-18... Battery voltage Rated speed 1 / 2 / 3 / 4 Collet diameter Collet diameter Abrasive grinding body diameter max. Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah...
2 1 7 3 4 6 5 8 Device description VI 1 Collet / Nut 2 Mode selector 6 Switch lock-off 3 Fuel gauge 8 Battery 7 Paddle switch 4 Handle Insulated gripping surface 5 LED light DIE GRINDER SAFETY WARNINGS Safety Warnings Common for Grinding, Sanding, Wire Brushing or Abrasive Cutting-Off Operations a) This power tool is intended to function as a grinder, sander, wire brush, polisher, carving or cut-off tool.
Kickback and Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
VI Do not let any metal parts enter the airing slots - danger of short circuit! Always use and store accessories according to the manufacturer‘s instructions. WARNING! Danger of burns! The wheel and workpiece will become hot during use. Wear gloves when changing discs or touching workpiece. Keep hands away from the grinding area at all times.
MAINTENANCE Remove the battery pack before starting any work on the appliance. The ventilation slots of the machine must be kept clear at all times. Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses). If needed, an exploded view of the tool can be ordered. Please state the Article No.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
