Instructions / Assembly

ManualsBrandsMillennium Lock ManualsKitchenSatin Nickel Door Locking Ultimate Lock System

The Ultimate Lock™ 3000 Series Installation Guide

a. This lock is designed for a right- or left-handed door that opens into the home or ofce with a deadbolt

currently installed at a 2-3/8" or 2-3/4" backset (centered from the edge of the door). It can be installed on an

outward swinging door, but special instructions are required. See www.TheUltimateLock.com for details.

b. To provide maximum protection, The Ultimate Lock™ should be installed in a solid 1-3/4” thick wood door or

steel-skinned, insulation or foam lled door mounted in a double studded door frame.

c. If your door does not already have a deadbolt installed, it is highly recommended that you purchase an

installation jig kit for deadbolts and door handles. These kits include special hole saws, templates, and other aids

to simplify the installation process. If your door has a metal skin, be sure your kit includes Bi-Metal hole saws to

cut the metal door.

If your door jamb/frame is steel, do not remove the hinge screws! See step 2.

Check www.TheUltimateLock.com to get information on installing the striker plate on a steel door frame.

Congratulations on purchasing the nest engineered deadbolt

lock on the market, The Ultimate Lock™. It is vital that your

lock is installed properly to provide the maximum protection

possible. Read these instructions completely before you begin

the installation. More information can be found at our website:

www.TheUltimateLock.com.

IMPORTANT: Register your lock’s serial number!

Go to www.TheUltimateLock.com and click the “Register Your

Lock” link.

• No. 1 and No. 2 Phillips Screw drivers or bits

• Pencil or steel marking pawl

• Electric drill (3/8" chuck) with torque adjustment

• Drill bits:

1/16"(1.5 mm)

3/32" (2.5 mm)

1/8" (3 mm)

9/64" (3.5 mm)

5/32" (4 mm) (supplied in kit)

• Spade bit or forester bit: 3/4", and 1"

• Hammer, steel center punch, and 1/2" and 3/4"

chisels

• Small carpenter’s square (adjustable)

• Pliers (needle nose and regular)

• Spray lubricant (dry Teon, Silicon Spray, or similar)

• Tape measure or 12-inch ruler

• (If no deadbolt installed) Wood or bi-metal hole

saw: 2-1/8" and 1"

• Wood chisel: 1/2" (13 mm)

• Small carpenters adjustable square

Every Ultimate Lock™ is thoroughly inspected before leaving the factory. It is warranted to be free of defects from workmanship and materials for a period

of TEN YEARS from the date of original purchase. Should any trouble develop during the TEN YEAR period, return the complete lock system, freight

prepaid, to Ultimate Lock, Inc. at 3776 Greenbriar Dr., Stafford, TX 77477 or call 1-866-MLS-4005 (1-866-657-4005) for one of Ultimate’s Authorized Service

Centers nearest you. If our inspection shows the trouble was caused by defective workmanship or material, Ultimate Lock™ will repair (or at our option)

replace the lock without charge. Register your Serial Number on line at www.theultimatelocksystems/warranty.com This Warranty does not apply where:

• Repairs have been made or attempted by others

• Repairs are required because of normal wear and tear

• The lock has been abused, misused or improperly installed

• Alterations have been made to the lock or its components

In no event shall Ultimate Lock™ be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies

both during and after the term of the warranty. Ultimate Lock™ disclaims liability for any implied warranties, including implied warranties of “merchantability”

and “tness for a specic purpose”, after the TEN-year term of this warranty. This warranty gives you specic legal rights, and you may also have other

rights, which vary from state to state. Some states do not allow the exclusion or the limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

*Disclaimer: The Ultimate Lock is only as strong as your door frame. Please contact your local locksmith to visit your home and evaluate your current setup.

Before You Start

Tools You Will Need

A Note About Steel Doors

Limited Warranty

Summary of content (8 pages)

PAGE 1
The Ultimate Lock™ 3000 Series Installation Guide Congratulations on purchasing the finest engineered deadbolt lock on the market, The Ultimate Lock™. It is vital that your lock is installed properly to provide the maximum protection possible. Read these instructions completely before you begin the installation. More information can be found at our website: www.TheUltimateLock.com. IMPORTANT: Register your lock’s serial number! Go to www.TheUltimateLock.com and click the “Register Your Lock” link.
PAGE 2
1. Identify Your Parts Carefully unpack and check that all parts are in the package. Identify parts and hardware from Figure 1. Record the Serial Number (located inside the lock case) and Date Installed for your lock on the back of this instruction booklet and save this information for future reference. This information will be required if you ever require any warranty. 1 2 3 4 5 6 7 8 9 (qty. 1) (qty. 2) (qty. 6) (qty. 2) (qty. 2) (qty. 2) (qty. 6) (qty. 6) (qty.
PAGE 3
2. Reinforce Your Hinges a. It is very important to reinforce the hinges of your door to get maximum protection from forced entry. Your Ultimate Lock™ comes with 12 special screws to secure the hinges to the studs of the door frame, and not the door jamb. The six shorter screws go into the middle of the door edge if possible or one inside and one outside hole on a steel-skinned or thin door. b. See Figure 2 and remove half of the existing screws from each of the three hinges as shown in the diagram.
PAGE 4
. A Note About Steel Doors For steel doors with steel door jambs: When installing the Ultimate Lock™ in steel doors or wood doors installed in steel door frames that have not yet had a deadbolt installed in them but have a deadbolt latch hole already in the door frame, the lock must be installed in line with the hole in the steel door jamb for the deadbolt striker (usually covered with a plate).
PAGE 5
7. Install Deadbolt a. Look at your door from the inside of the house or room and note if the hinges are on the right or left side of the door. b. For a door with hinges on the right, install deadbolt with the cross hole at the bottom. For a door with hinges on the left, install the deadbolt with the cross hole on top (Figure 7). c. Mark and drill two 3/32" (2 mm) pilot holes for the two faceplate screws , insert the deadbolt properly and install the screws.
PAGE 6
9. Install Security Bar d. The gear should slide in smoothly. Using the key in the key lock, see if the gear turns smoothly. If you cannot turn the gear smoothly go to www.TheUltimateLock.com for correction instructions. PATENT PENDING c. Align the arrow on the first tooth of the gear with the marking corresponding to the backset measurement previously recorded and engage the gear teeth (Figure 9), making sure that flat tailpiece of key lock properly mates with gear cross hole. 238 b.
PAGE 7
3 Platform Housing 2 Decorative Cover 1 Twist Knob Figure 11 11. Install Striker Plate a. Remove the old deadbolt striker plate from the door frame. Close the door and see if the new deadbolt aligns with the old hole in door jamb. If not, use the 1" spade bit to enlarge the old hole for the new bolt. Make sure it will extend the full 1” depth and the security button will engage. b. With the deadbolt partially extended, close the door until the deadbolt touches the door frame.
PAGE 8
TIP: Do not force the screws in. If the screws get too tight before they are all the way in, either apply soap to screw threads, or carefully remove the screw and re-drill the pilot hole and try again. For steel door frames: If the door jamb is steel you will have to surface-mount the striker plate and drill 2-5/8" holes in the steel frame at the point of the mounting holes in the striker plate to accommodate the dimples in the striker plate.