Laundry Room Cabinetry Assembly Guides IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. https://millspride.com/rta Scan this code for more detailed instructions, assembly videos and to register your cabinet warranty. www.
60" Wide Laundry Cabinet - LW60 Page 2-7 60" Wide Laundry Cabinet & Pole Set - LP60 Page 8-14 18" Wall Cabinet - LW1830 Page 15-20 18" Base Cabinet - LBD18 Page 21-30 36" Base Cabinet - LB36 Page 31-39 18" Linen Cabinet - LT18 Page 40-51 www.millspride.
LW60 60” Laundry Wall Cabinet Assembly Guide - LW60 IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. www.millspride.
60” Laundry Wall Cabinet LW60 PARTS 2 x End Panels with Pre-installed Hardware F 1 x Face Frame with Pre-installed Hardware 2 x Doors 2x Fixed Shelves with Pre-installed Hardware G 2 x Divider Panels 1 x Central Shelf I H 1 x Back Panel with Pre-installed Hardware 4 x Soft Close Hinges L M N O J K 4 x Clear Bumpers 2 x Adjustable Shelves 12 x Metal Shelf Rests 24- #6 x 1/2" Pan Head Screws 8 - #6 x 5/8" Flat Countersink Screws 4 - #8 x 7/8" Pan Washer Head Screws 14 - #6 x 1" Flat Countersin
60” Laundry Wall Cabinet LW60 Step 1 Start by laying the Frame (A) face down on a smooth flat surface. Insert the (2) End Panels (B) into the outer grooves in the Frame (A), as shown, so that the L-Brackets and Connector Plates ‘snap’ together. Align the panels and secure the Connector Plates with locking (8) #6 x 1/2" Pan Head screws (L). Step 2 Slide the (2) Fixed Shelves (C) into the horizontal grooves in the End Panels (B) and Frame (A), so that the L-Brackets and Connector Plates ‘snap’ together.
0” Laundry Wall Cabinet LW60 Step 3 Slide (2) Divider Panels (D) into grooves in Fixed Shelves (C) and ensure they are fully seated in grooves in Face Frame (A). Step 4 Carefully install the Back Panel (E), so that the L-Brackets and Connector Plates ‘snap’ together. This may require a second person. Ensure the Divider Panels are fully seated in the grooves in the Back Panel and the cabinet is square.
60” Laundry Wall Cabinet LW60 Step 5 Carefully, turn the cabinet over and tighten the Connector Plate screws holding the Back Panel (E) in place. Lock the plates and L-brackets together using (8) #6 x 1/2" Pan Head locking screws (L). Step 6 Lay the (2) Doors (F) face down on a smooth flat surface and install (4) Hinges (H) using (8) #6 x 5/8” Flat Head screws (M). F F www.millspride.
60” Laundry Wall Cabinet LW60 Step 7 Attach the (2) Doors (F) to the Face Frame (A) using (4) #8 x 7/8” Pan Washer Head screws (N) and install (4) Clear Bumpers (J). F F Step 8 Insert (4) Metal Shelf Rests (K) in the open middle section and install Central Shelf (G). Insert (4) Metal Shelf Rests (K) in each of the outer sections and install (2) Adjustable Shelves (I). I I G www.millspride.
LP60 Laundry Cabinets with Hanging Rod Assembly Guide - LP60 IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. www.millspride.
Laundry Cabinets with Hanging Rod LP60 PARTS 2 x Face Frames with Pre-installed Hardware 2 x Back Panels with Pre-installed Hardware 4 x End Panels with Pre-installed Hardware 2 x Doors G F 1 x Adjustable Hanging Rod 2 x Adjustable Shelves 4 x Fixed Shelves H I 4 x Soft Close Hinges J 8 x Locking Shelf Rests 4 x Clear Bumpers K 2 x Rod Sockets 32 - #6 x 1/2" Pan Head Screws 8 - #6 x 5/8" Flat Countersink Screws 4 - #8 x 7/8" Pan Washer Head Screws 8 - #6 x 1" Flat Countersink Screws www.
Laundry Cabinets with Hanging Rod LP60 Step 1 Start by laying Frame (A) face down on a smooth flat surface. Insert the front edges of (2) End Panels (C) into the vertical grooves in the Frame (A), so the L-Brackets and Connector Plates ‘snap’ together. Align the panels so the grooves line up and tighten the Connector Plate Screws. Then, secure the Connector Plates with (8) #6 x 1/2" Pan Head locking screws (L).
Laundry Cabinets with Hanging Rod LP60 Step 3 Apply beads of glue and carefully install Back Panel (B) into grooves in rear of End Panels (C), so that L-Brackets and Connector Plates snap together. Ensure Fixed Shelves (E) slot into grooves in Back Panel (B). Step 4 Carefully, turn the cabinet over and tighten the Connector Plate screws holding the Back Panel (B) in place. Lock the plates and L-brackets together using (8) #6 x 1/2" Pan Head locking screws (L). www.millspride.
Laundry Cabinets with Hanging Rod LP60 Step 5 Turn the cabinet over again and insert (4) #6 x 1” Flat Head screws (O) through holes in Back Panel (B). Tighten securely into Fixed Shelves (E). Step 6 Insert (4) Locking Shelf Rests (I) in desired location and install Adjustable Shelf (F). F www.millspride.
Laundry Cabinets with Hanging Rod LP60 Step 7 Install Rod Socket (K) in the desired location, immediately behind the Frame (A), using the screws provided. K REPEAT STEPS 1-7 TO BUILD THE OTHER CABINET REPEAT - Step 8 Lay the (2) Doors (D) face down on a smooth flat surface and install (4) Hinges (H) using (8) #6 x 5/8” Flat Head screws (M). www.millspride.
Laundry Cabinets with Hanging Rod LP60 Step 9 Attach the Door (D) to the Face Frame (A) using (4) #8 x 7/8” Pan Washer Head screws (N) and install (2) Clear Bumpers. Repeat the process on the other cabinet. Step 10 IMPORTANT! Consult a professional to determine the best hardware required to mount the (2) cabinets securely to your wall. To install the Hanging Rod (G) between the cabinets, insert the rod into one bracket, extend the rod into the other bracket and twist it to lock in place. G www.
LW1830 18" x 30" Wall Cabinet Assembly Guide LW1830 IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. www.millspride.
18" x 30" Wall Cabinet LW1830 PARTS F 1 x Face Frame with Pre-Installed Hardware 1 x Back Panel with Pre-Installed Hardware 2 x End Panels with Pre-Installed Hardware 2x Fixed Shelves 1 x Door P I 8 x Locking Shelf Rests 2 x Adjustable Shelves 2x Hinges 2 x Bumpers 16 - #6 x 1/2" Pan Head Screws 4 - #6 x 5/8" Flat Countersink Screws 2 - #8 x 7/8" Pan Washer Head Screws 4 - #6 x 1" Flat Countersink Screws www.millspride.
" x 30" Wall Cabinet LW1830 Step 1 Run a bead of wood glue in vertical grooves in the Frame (A) and insert End Panels (C) into the grooves, so that L-Brackets (G) and Connector Plates (H) 'snap' together. H Align the panels so the dado grooves line up and tighten the Connector Plate screws. Then secure the Connector Plates and LBrackets with (8) #6 x 1/2" Pan Head locking screws. G Step 2 Run beads of glue in the horizontal grooves in End Panels (C) and Frame (A) and insert Fixed Shelves (D). www.
18" x 30" Wall Cabinet LW1830 Step 3 Apply beads of glue and carefully install Back Panel (B) into grooves in rear of End Panels (C), so that L-Brackets (G) and Connector Plates (H) snap together. Ensure Fixed Shelves (D) slot into grooves in Back Panel (B). Step 4 Turn the cabinet over, make sure it is square and tighten the Connector Plate screws. Then secure the Connector Plates and L-Brackets with (8) #6 x 1/2" Pan Head locking screws. www.millspride.
18" x 30" Wall Cabinet LW1830 Step 5 Turn the cabinet over again and insert (4) #6 x 1” Flat Head screws thru holes in Back Panel (B). Tighten securely into Fixed Shelves (D). Step 6 Insert (4) Locking Shelf Rests (I) in desired locations and install Adjustable Shelves (E) www.millspride.
18" x 30" Wall Cabinet LW1830 Step 7 Lay the Door (F) face down on a smooth surface and install (2) Hinges (P) using (4) #6 x 5/8” Flat Head Screws F Step 8 Attach Door (F) to the Face Frame (A) using (2) #8 x 7/8” Pan Washer Head screws and install (2) Clear Bumpers IMPORTANT! Consult a professional to determine the best hardware required to mount the cabinet securely to your type of wall. www.millspride.
LBD18 18" 3-Drawer Base Cabinet Assembly Guide LBD18 IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. www.millspride.
18" 3-Drawer Base Cabinet LBD18 PARTS 2x I-Beams I D 1 x Face Frame with Pre-Installed Hardware T 1 x Back Panel with Pre-Installed Hardware 1 x Left End Panel with Pre-Installed Hardware 1 x Shallow Drawer Box Back H 1 x Integral Toe Kick E 3 x Drawer Bottoms U 4 x Deep Drawer Box Sides w 3 x Left Locking Devices 1 x Fixed Shelf 1 x Shallow Drawer Front Q 2 x Deep Drawer Front O N 2 x Deep Drawer Box Backs v 1 x Right End Panel with Pre-Installed Hardware 2x Shallow Drawer Sides
18" 3-Drawer Base Cabinet LBD18 Step 1 Run a bead of white wood glue in the vertical grooves in the Face Frame (A). Insert End Panels (C and D), so that L-Brackets (K) and Connector Plates (L) snap together. Now tighten the Connector Plate screws and secure them and the LBrackets with (8) #6 x 1/2" Pan Head locking screws. Step 2 Run a bead of wood glue in the lower horizontal grooves in the Frame (A) and End Panels (C and D) and slide the Fixed Shelf (F) completely into the grooves. F www.
18" 3-Drawer Base Cabinet LBD18 Step 3 Run a bead of wood glue in the horizontal grooves in the End Panels (C and D) and insert I-beams (I). I F I F Step 4 Apply a bead of wood glue to the recesses along the back edges of the End Panels (C and D) and in the lower horizontal groove in Back Panel (B). Carefully install Back Panel (B) so that the panels align and the L-Brackets & Connector Plates snap together.
18" 3-Drawer Base Cabinet LBD18 Step 5 Carefully turn the cabinet over, make sure it is square, tighten all the Connector Plate screws and then secure the Connector Plates and L-brackets with(8) #6 x 1/2" Pan Head locking screws. Step 6 Make sure Back Panel (B) is correctly installed and insert (4) #6 x 1" Countersink Flat Head screws through the predrilled holes. Tighten the screws securely into the Fixed Shelf (F) and I-beams (I). www.millspride.
18" 3-Drawer Base Cabinet LBD18 Step 7 At the Toe Kick cutout, attach (2) silver L-brackets (G) to the End Panels (C and D) with (4) #8 x 1/2" Pan Head screws. G G Step 8 Mount the integral Toe Kick (E) to the silver L-brackets (G) using (4) #8 x ½” Pan Head screws. E www.millspride.
18" 3-Drawer Base Cabinet LBD18 Step 9 Stand cabinet upright and insert (6) Runner Rear Brackets (J) into Back Panel (B) and secure with (12) #6 x 5/8" Countersink Flat Head screws. J J J J Step 10 Slide the Drawer Runners (M) into the Runner Brackets (J), rest the front on the Frame (A). M M Secure each runner to the side frame with (1) #6 x 5/8” Flat Head screw. Runner is set back slightly, so screw is located in the center of the frame. www.millspride.
18" 3-Drawer Base Cabinet LBD18 Step 11 DRAWER BOX ASSEMBLY Put a dab of glue into the dovetail recesses in the Drawer Fronts and Drawer Backs. For Upper (Shallow) Drawer : T H Front (Q), Back (T) R For Lower (Deep) Drawers Front (O), Back (H) N U R N Q O Step 12 DRAWER BOX ASSEMBLY Lay Drawer Side on a smooth flat surface and insert the Front and Back panels, ensuring that bottom grooves line up.
18" 3-Drawer Base Cabinet LBD18 Step 13 DRAWER BOX ASSEMBLY Slide the Drawer Bottom (U) into the grooves and install the other Drawer Side. If necessary, use a rubber mallet to gently tap the joints into place. R N U Step 14 DRAWER BOX ASSEMBLY To secure the drawer boxes, while the glue sets up, add (12) #6 x 1" Countersink Flat Head screws in predrilled holes in Side and Back of the drawers. www.millspride.
18" 3-Drawer Base Cabinet LBD18 Step 15 Turn the drawers over and install a pair of Locking Devices (V and W) at the front of each drawer, using (12) #6 x 5/8” Pan Head screws. Do not overtighten the screws. V V W W Step 16 Fully extend the Drawer Runners (M). Sit the drawer on the runners. M Under the drawer, slide the runners forward until they lock into the Locking Devices. Then close drawer to fully engage.
LB36 36" Laundry Base Cabinet Assembly Guide LB36 IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. www.millspride.com/rta Scan this code for more detailed instructions, assembly videos and to register your cabinet warranty.
36" Laundry Base Cabinet LB36 PARTS 1 x Face Frame with Pre-Installed Hardware 1 x Right End Panel with Pre-Installed Hardware 1 x Back Panel with Pre-Installed Hardware 1 x Left End Panel with Pre-Installed Hardware I O 2 x Doors 1 x Integral Toe Kick 2 x I-Beams H F 1 x Fixed Shelf 4x Bumpers 1 x Adjustable Shelf G J 5x L-Brackets 5 x Locking Shelf Rests P 4x Hinges 20 - #8 x 1/2" Pan Head Screws 16 - #6 x 1/2" Pan Head Screws 8 - #6 x 5/8" Flat Countersink Screws 4 - #8 x 7/8" Pan Was
36" Laundry Base Cabinet LB36 Step 1 Run a bead of wood glue in the grooves in the back of Frame (A) and insert End Panels (C and D) so that L-Brackets (K) and Connector Plates (L) snap together. Align the panels so the grooves line up and secure the Connector Plates and LBrackets with (8) #6 x 1/2" Pan Head locking screws. L K Step 2 Run a bead of wood glue in the lower grooves in Face Frame (A) and End Panels (C and D) and insert Fixed Shelf (F).
36" Laundry Base Cabinet LB36 Step 3 Run a bead of wood glue in the upper grooves in End Panels (C and D) and insert (2) IBeams (I) I I Step 4 Apply beads of wood glue to recesses in back of End Panels (C and D) and carefully install Back Panel (B) into grooves in End Panels (C and D), so that L-Brackets (K) and Connector Plates (L) snap together. Ensure Fixed Shelf (F) fits into groove in Back Panel (B). www.millspride.
" Laundry Base Cabinet LB36 Step 5 Ensure I-Beams (I) are correctly seated and attach them to Face Frame (A) using (2) Silver L-Brackets (G) and (8) #8 x 1/2" Pan Head screws. I Step 6 Insert (5) #6 x 1” Flat Head screws thru holes in Back Panel (B). Tighten them into Fixed Shelf (F) and I-beams (I). www.millspride.
36" Laundry Base Cabinet LB36 Step 7 Turn the cabinet over, make sure it is square and secure the Connector Plates with locking screws: (8) #6 x 1/2" Pan Head. Step 8 At the toe kick cutout, attach (2) silver L-Brackets (G) to End Panels with (4) #8 x 1/2" Pan Head screws. www.millspride.
36" Laundry Base Cabinet LB36 Step 9 Attach integral Toe Kick (E) and secure with (4) #8 x 1/2" Pan Head screws. Step 10 Lay the Doors (O) face down on a smooth flat surface and install (4) Hinges (P) using (8) #6 x 5/8” Flat Head screws. O www.millspride.
36" Laundry Base Cabinet LB36 Step 11 Attach Doors (O) to the Face Frame (A) using (4) #8 x 7/8” Pan Washer Head screws and install (2) clear bumpers on each door. Step 12 Insert (5) Locking Shelf Rests (J) in desired location and install Adjustable Shelf (H). H www.millspride.
LT18 18" x 64½" LaundryTower Assembly Guide LT18 IMPORTANT NOTES Before you start, inspect all panels and hardware to ensure you have everything needed. We recommend laying the panels on some cardboard to protect the finish when assembling. In addition to the pre-installed hardware, we recommend adding a bead of white wood glue in the dado grooves, to create the strongest cabinet. www.millspride.com/rta Scan this code for more detailed instructions, assembly videos and to register your cabinet warranty.
18" x 64½" LaundryTower LT18 PARTS N 1 x Left Lower End 1 x Right Lower with Pre-Installed End with PreHardware Installed 1 x Lower Frame with Pre-installed Hardware 1 x Upper UFrame with Preinstalled Hardware 2 x Doors 1 x Lower Back with Pre-Installed Hardware Hardware J K L 1 x Upper Back with Preinstalled Hardware M 2 x Fixed Shelves Q 2 x Adjustable Shelves 1 x Left Upper End 1 x Left Upper End with Pre-installed with Pre-installed Hardware Hardware G 2 x Silver LBrackets H I 6 x Wo
18" x 64½" LaundryTower LT18 Step 1 Lay the Lower Frame (A) face down on a smooth flat surface and run a bead of glue in the vertical grooves. Step 2 Insert the Lower Ends (B and C) so that the L-Brackets on the Frame (A) and the Connector Plates on the Ends (B and C) ‘snap’ together. Align the panels so the dado grooves line up and tighten the Connector Plate screws. Then, lock the Plates and LBrackets together with (4) #6 x 1/2" Pan Head screws. www.millspride.
18" x 64½" LaundryTower LT18 Step 3 Run beads of glue in the lower grooves in Frame (A) and Lower Ends (B and C) and insert (1) Fixed Shelf (E). Step 4 Apply beads of glue to recesses in back of Lower Ends (B and C) and groove in Lower Back (D). Carefully install Lower Back (D) so that the L-Brackets and Connector Plates 'snap' together. www.millspride.
18" x 64½" LaundryTower LT18 Step 5 Ensure the brackets and plates are connected, insert (2) #6 x 1" Flat Head screws thru holes in Lower Back and fully tighten into Fixed Shelf (E). Step 6 Carefully turn the cabinet over and tighten the Connector Plate screws. Then, secure the brackets together using (4) #6 x 1/2" Pan Head locking screws. www.millspride.
18" x 64½" LaundryTower LT18 Step 7 At the Toe Kick cutout, attach (2) Silver L-Brackets (G) to the Lower Ends (B and C) using (4) #8 x 1/2" Pan Head screws. Step 8 Mount the Toe Kick (F) to the Silver L-Brackets (G) using (4) #8 x 1/2" Pan Head screws. Ensure the outer edges of the Toe Kick align with the edges of the Frame (A). F www.millspride.
18" x 64½" LaundryTower LT18 Step 9 Stand the cabinet upright and insert small daps of glue in the (6) slots in Lower Ends (B and C) and Lower Back (D) and the (4) holes in the top of Frame (A). Then, insert (6) Wood Biscuit Joints (H) and (4) Wood Connector Dowels (I). Step 10 Lay the Upper U-Frame (J) face down on a smooth flat surface and run a bead of glue in the vertical grooves. J www.millspride.
18" x 64½" LaundryTower LT18 Step 11 Insert the Upper Ends (K and L) so that the L-Brackets on the U-Frame (J) and the Connector Plates on the Ends 'snap' together. L Align the panels and tighten the Connector Plate screws. Then, lock the brackets together using (8) #6 x 1/2" Pan Head locking screws. K J Step 12 Run beads of glue in the upper grooves in U-Frame (J) and Upper Ends (K and L) and insert (1) Fixed Shelf (E). J www.millspride.
18" x 64½" LaundryTower LT18 Step 13 Apply beads of glue to recesses in back of Upper Ends (K and L) and groove in Upper Back (M). Carefully install Upper Back (M) so that the L-Brackets and Connector Plates 'snap' together. M K Step 14 Ensure the brackets and plates are connected, insert (2) #6 x 1" Flat Head screws thru holes in Lower Back and fully tighten into Fixed Shelf (E). M www.millspride.
18" x 64½" LaundryTower LT18 Step 15 Carefully turn the cabinet over and tighten the Connector Plate screws. Then, secure the brackets together using (8) #6 x 1/2" Pan Head locking screws. Step 16 Insert small daps of glue into the (6) slots in the bottom edge of Upper Ends (K and L) and Upper Back (D) and in the (4) holes in the bottom of U-Frame (J). Then, carefully place the upper cabinet onto the lower cabinet, making sure the Wood Biscuit Joints and wood Dowels are fully inserted.
18" x 64½" LaundryTower LT18 Step 17 In the back, where the two cabinet sections meet, attach the (2) tan L-Brackets to the Lower Back (D) using (2) #6 x 1/2" Pan Head screws. Then, attach the (4) loose Connector Plates to the Lower Back (D) and the Lower Frame (A) using (4) #6 x 1/2" Pan Head screws. Finally, secure the plates and brackets together using (8) #6 x 1/2" Pan Head locking screws.
18" x 64½" LaundryTower LT18 Step 19 Lay the (2) Doors (N) face down on a smooth flat surface and install (4) Soft Close hinges (O) using (8) #6 x 5/8" Flat Head Screws. N N Step 20 Mount the (2) Doors (N) onto the Frames (A and J) using (4) #8 x 7/8" Pan Washer Head screws. www.millspride.
18" x 64½" LaundryTower LT18 Step 21 Install Rod Socket (K) in the desired location, immediately behind the Frame (A), using the screws provided. Step 22 To install the Adjustable Hanging Rod (S) between (2) towers, insert the rod into one socket, extend the rod into the other bracket, and twist it to lock in place. IMPORTANT! Consult a professional to determine the best hardware required to mount the tower securely to your type of wall. www.millspride.
