Installation Guide

ManualsBrandsMighty Mule ManualsLumber & CompositesAutomatic Cable Gate Lock

WIRELESS

Cable/Gate Lock

INSTALLATION MANUAL

ACCESS CONTROLS

www.mightymule.com

Gates that Open, LLC • 3121 Hartsﬁeld Road • Tallahassee, Florida 32303

1-800-543-GATE (4283) • Technical Support 1-800-543-1236

DRILL CLEARANCE HOLE

FOR

1/2" BOLT

DRILL CLEARANCE HOLE

FOR

1/2" BOLT

MOUNTING TEMPLATE

CABLE GATE

LOCK

This convenient battery powered wireless lock has many uses, including; multiple user

access to property, securing items such as boats or trailers and anything else secured

with a chain or cable.

Items Required - not included:

1. (8) AA Batteries*

2. (2) 3/8” carriage bolts, (2) 3/8” nuts and (2) 3/8”

washers (bolts must be at 1” longer than thickness

of gate post you are mounting to)

3. Other hardware may be needed depending on type

of cable, rope or chain being used. See EXAMPLES

on page 6.

Kit Includes:

A. Lock (1)

B. Keys (2)

C. Cable/Chain Ring (1)

D. Mounting Template (1)

E. Remote Transmitter (1)

Gate Chain Lock

Driveway Cable Lock

To use as a lock for gate chain,

mount lock on outside face of non-

hinge post as illustrated.

To use as a lock for driveway

cable, mount lock on post facing

Summary of content (8 pages)

PAGE 1
Cable/Gate Lock INSTAL L AT ION ACCESS CONTROLS WIRELESS MANUA L This convenient battery powered wireless lock has many uses, including; multiple user access to property, securing items such as boats or trailers and anything else secured with a chain or cable. Driveway Cable Lock To use as a lock for driveway cable, mount lock on post facing other driveway post as illustrated. Gate Chain Lock To use as a lock for gate chain, mount lock on outside face of nonhinge post as illustrated. Kit Includes: A.
PAGE 2
STEP 1: Remove Lock Housing 1 2 3 Place key in lock and turn clockwise disengaging cable hook. Remove cover fastener. Remove cover. 2 Cable/Gate Lock Instruction Manual • REV 10.29.
PAGE 3
STEP 2: Attach Lock to Post Cable Lock Option mounts on side of post facing other drive post 1 2 Gate Lock Option mounts on outside of non-hinged gate post Affix included mounting template to post, and drill 3/8” holes through post. Use 3/8” carriage bolts, washers, and nuts to fasten as shown. Bolt must penetrate post with a maximum of 1” extra for securing washer and nut Cable/Gate Lock Instruction Manual • REV 10.29.
PAGE 4
STEP 3: Install 8 AA Lithium Batteries 1 Install the 8 AA batteries based on your application. See chart below.* * AA Battery Operating Temperature (Energizer™): Alkaline: 0°F to 130°F Lithium: -40°F to 140°F STEP 4: Setting Your Personal Code All GTO transmitters are set to a standard settings and are ready to operate lock. For your safety and security, we strongly recommend replacing the factory setting with your own.
PAGE 5
STEP 5: Learning the Transmitter SOLAR – + LEARN 1 REMOTE Press and hold “LEARN REMOTE” button on control board and the transmitter button at the same time until you hear beep, then release. LEARN 2 Your personal transmitter setting is now programmed. BATT 3 REMOTE Test lock. Secure cable hook, press and hold transmitter button to ensure the cable hook releases. STEP 6: Re-attach the Lock Housing 1 Replace lock housing and secure with housing screw. Cable/Gate Lock Instruction Manual • REV 10.
PAGE 6
STEP 7: Attaching Lock Ring Examples If using an existing cable, verify you have enough slack in cable to attach ring using directions below. Leave approximately 6 inches of slack for every 10 feet of cable.. If using new cable, attach ring to one end and attach other end to second post with secure mounting hardware, leaving approximately 6 inches of slack for every 10 feet of cable. 1 Attach cable or rope to ring (included) using optional hardware (not supplied).
PAGE 7
Care and Maintenance 1. Periodically lubricate the illustrated points with silicon to keep the lock working smoothly. 2. Check and replace batteries if lock fails to disengage. IMPORTANT: Take special care to avoid getting lubricant on electrical components. Lubricate these points periodically to keep lock working smoothly. Optional Accessories Additional transmitter (FM135) for family and friends.
PAGE 8
FCC WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In accordance with FCC Part 15, Section 15.21, the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could VOID the user authority to operate the equipment.