Operating instructions Heat pump tumble dryer It is essential to read these operating instructions before installing and using the appliance. This prevents both personal injury and damage to the appliance. en-AU, NZ M.-Nr.
Contents Caring for the environment ............................................................................. 6 Warnings and safety instructions ................................................................... 7 Operating the tumble dryer .............................................................................. Control panel ....................................................................................................... How the programme selector works ................................
Contents Programme chart .............................................................................................. 35 Changing the programme sequence ............................................................... 38 Changing a programme after it has started ........................................................ 38 Adding or removing laundry ................................................................................ 38 Condensed water container ...................................................
Contents Installation.......................................................................................................... Front view ............................................................................................................ Rear view............................................................................................................. Transporting the tumble dryer .............................................................................
Contents Network ............................................................................................................... Switching off Wi-Fi ......................................................................................... RemoteUpdate ........................................................................................ Remote control ......................................................................................... SmartGrid (only functional in selected countries).....
Caring for the environment Disposal of the packing material Disposing of your old appliance The transport and protective packaging has been selected from materials which are environmentally friendly for disposal, and can normally be recycled. Electronic and electrical appliances contain many valuable materials. They also contain certain materials, compounds and components which were essential for their correct functioning and safety.
Warnings and safety instructions It is essential to read these instructions. This tumble dryer contains a refrigerant that is flammable and explosive. This tumble dryer complies with all current local and national safety requirements. However, inappropriate use can lead to personal injury and damage to property. Read the operating instructions carefully before using the tumble dryer. They contain important information on safety, installation, use and maintenance of the appliance.
Warnings and safety instructions Correct application This tumble dryer is designed for domestic use and for use in similar environments by guests in hotel or motel rooms, bed & breakfasts and other typical living quarters. This does not include common/shared facilities or commercial facilities within hotels, motels or bed & breakfasts. This tumble dryer is not suitable for outdoor use.
Warnings and safety instructions Technical safety Before setting up the tumble dryer, check it for any externally visible damage. Do not install or use a damaged tumble dryer. Before connecting the tumble dryer, ensure that the connection data on the data plate (fuse rating, voltage and frequency) matches the mains electricity supply. If in any doubt, consult a qualified electrician.
Warnings and safety instructions In the event of a fault or for cleaning purposes, the tumble dryer is only completely isolated from the electricity supply when: - it is switched off at the wall socket and the plug is withdrawn, or - it is switched off at the mains circuit breaker. This tumble dryer must not be installed and operated in mobile installations (e.g. on a ship). Do not make any alterations to the tumble dryer, unless authorised to do so by Miele.
Warnings and safety instructions The R290 refrigerant contained in this tumble dryer is flammable and explosive. If the tumble dryer is damaged, proceed as follows: - Avoid naked flames or anything which creates a spark. - Disconnect the dryer from the electricity supply. - Air the room where the tumble dryer is located. - Contact Miele Customer Service. Risk of fire and explosion due to damage to the tumble dryer. The refrigerant is flammable and explosive if it leaks.
Warnings and safety instructions Correct use Warning: Risk of fire / Flammable materials. To avoid the possible danger of fire, please read these warnings carefully. A clogged filter is a fire hazard! The fluff filter must be cleaned after every programme. The maximum load for this tumble dryer is 8.0 kg (dry weight). See the “Programme chart” for the maximum recommended loads for individual programmes. To prevent the risk of fire, do not connect the tumble dryer via a controllable socket (e.g.
Warnings and safety instructions The fluff filters must be cleaned after every drying cycle. Fluff must not be allowed to accumulate around the tumble dryer. The fluff filters and the plinth filter must be thoroughly dried after cleaning. Do not replace them if they are damp or wet. Damp or wet filters could cause operational faults. Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer.
Warnings and safety instructions When washing such heavily soiled items: Ensure that you use a larger quantity of detergent and select a high temperature. If in doubt, wash the items several times. To prevent the risk of fire, the following textiles must never be dried in the tumble dryer: - Textiles that have been cleaned using chemicals (e.g. professional dry-cleaning agents). - Textiles which contain a large proportion of rubber, foam rubber or rubber-like materials.
Warnings and safety instructions In many programmes, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry selfigniting). The programme is not finished until the cooling down phase has been completed. As soon as the programme has finished, remove all laundry from the drum. Always close the door after use.
Warnings and safety instructions Using a fragrance flacon (optional accessory) Only use genuine Miele original fragrance flacons. The fragrance flacon must be stored in its packaging so please make sure you retain this. Caution. The fragrance can run out of the flacon. Make sure that you always keep the flacon, or the fluff filter with the flacon inserted in it, upright when carrying and do not tip it or place it down on any surface.
Warnings and safety instructions Accessories Only use genuine Miele spare parts and accessories with this appliance. If spare parts or accessories from other manufacturers are used, this will invalidate the warranty, and Miele cannot accept liability. A Miele tumble dryer can be stacked on top of a Miele washing machine using the appropriate stacking kit (available as an optional accessory). Please make sure you order the correct one for the Miele washing machine and Miele tumble dryer.
Operating the tumble dryer Control panel a Control panel b Sensors for the drying levels c Indicator lights light up when necessary d Gentle tumble sensor for gentle drying e Time display for the programme duration 18 f Sensors for time selection g Start/Add laundry sensor for programme start and adding laundry h Optical interface for service technicians i Programme selector
Operating the tumble dryer How the programme selector works How the control panel works The programme selector is used to select programmes. The dryer is switched on by selecting a programme, and switched off by turning the programme selector to the position. MobileStart You can operate your tumble dryer remotely with the Miele App. Wash2Dry A drying programme tailored to the laundry is set in conjunction with the connected washing machine.
Operating the tumble dryer Indicator lights Time display - lights up when the condensed water container needs to be emptied. The remaining programme running time is displayed in hours and minutes. - lights up when the plinth filter needs to be cleaned. - PerfectDry The PerfectDry system measures the residual moisture present in the laundry in programmes with selectable drying levels and provides a more precise drying result.
Before using for the first time Miele@home Your tumble dryer is equipped with an integrated Wi-Fi module. In order to use it you need: - a Wi-Fi network - the Miele App - a Miele user account. The user account can be created via the Miele App. The Miele App will guide you as you connect your tumble dryer to your home Wi-Fi network.
Before using for the first time Wash2Dry Once the wash programme has completely finished, the Miele washing machine transfers the programme data via the router to which the networked tumble dryer is also connected, as well as transferring it to the Miele Cloud. The tumble dryer automatically sets a drying programme tailored to the laundry based on the transferred programme data. All you need to do is start the drying programme once you have loaded the tumble dryer.
Before using for the first time Downtime after installation Setting up Miele@home Damage to the tumble dryer by There are 2 ways of connecting: switching it on too soon. This can damage the heat pump. After setting up the tumble dryer, wait for at least one hour before switching it on. 1. Via the Miele App (default) 2. Via WPS To do so, you will need a WPScompatible router.
Before using for the first time Logging in via WPS Turn the programme selector to MobileStart . Follow the procedure for using for the first time outlined in these instructions Touch the sensor until appears in the time display and a short keypad tone sounds. Refer to “1. Notes on correct laundry care” and “2. Loading the tumble dryer”. The timeout time then starts to count down from 2 minutes in the time display.
Energy saving tips This dryer with heat-pump technology is designed for energy-saving drying cycles. You can save even more energy with the following measures, because the drying time is not extended unnecessarily. - Make sure your laundry is spun at the maximum spin speed before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying, e.g. approx. 20% energy can be saved if spinning laundry at 1600 rpm instead of 1000 rpm.
1. Notes on correct laundry care Points to note regarding washed laundry - When washing very heavily soiled items, ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. - Do not put soaking wet items into the tumble dryer. Make sure your laundry is thoroughly spun before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying.
1. Notes on correct laundry care Drying Care label symbols Useful tip: See the "Programme chart". It lists all programmes and their maximum load. Drying - Always observe the maximum recommended load for each programme. This will mean that the energy consumption for the amount of laundry is the most economical. Reduced temperature* - Down-filled garments have linings which have a tendency to shrink, depending on the quality of the item. Only use the Woollens handcare programme for these textiles.
2. Loading the tumble dryer Loading the laundry Textiles may be damaged. Before loading, read chapter “1. Notes on correct laundry care” first. Open the door. Remove any items that have been left inside the drum. Socket for the fragrance flacon See the section “Fragrance flacon” for information on how to use fragrance flacons. If you are not using a fragrance flacon: Push the tab down completely (see arrow) so that the socket is closed. Otherwise, fluff will accumulate here.
3. Selecting a programme and starting it Switching on the tumble dryer The dryer is switched on by selecting a programme, and switched off by turning the programme selector to the position. 3. Selecting a drying programme via the Wash2Dry programme selector position Turn the programme selector to Wash2Dry . If the connection is successful, ...... will flash in the display, followed by .
3. Selecting a programme and starting it Selecting a drying level with a drying programme Cottons, Minimum iron, Delicates, Shirts, Express, Bed linen The preset drying level for the programme can be changed if required. Selecting timed drying programmes and other programmes Warm air/DryFresh You can set the duration in ten-minute increments from minutes to hours. Touch the sensor for the drying level you want. It will light up brightly.
3. Selecting a programme and starting it Selecting Gentle tumble Delicate fabrics (with the symbol on the care label, e.g. acrylic garments) are dried at a lower temperature and with a longer programme duration. Touch the Gentle tumble sensor. It will light up brightly. - Gentle tumble can be selected with the following programmes: – Cottons – Minimum iron – Shirts – Warm air/DryFresh - Gentle tumble is always activated/ cannot be deselected with Delicates.
4. Removing the laundry at the end of the programme End of programme/Anti-crease End of programme: lights up in the time display and the Start/Add laundry sensor goes out. A signal tone (buzzer) sounds. Always remove all items from the drum. Items left in the dryer could be damaged by overdrying when the dryer is used the next time. The end of the programme is followed by the Anti-crease phase, which will run for up to 2 hours.
Delay start/SmartStart Altering Delay start Selecting Delay start With Delay start you can delay the start of a programme from minutes up to (hours). However: Delay start cannot be used with the Warm air/DryFresh programme. Touch the sensor. The sensor lights up brightly. Touch the or sensor repeatedly until the required delayed start time appears in the time display.
Delay start/SmartStart SmartStart The SmartStart function (only available in selected countries) lets you define a time period during which your tumble dryer will start automatically. The machine will start on receipt of a signal, e.g. from your energy supplier, that indicates that the electricity rate is particularly economical. This function is active when the SmartGrid programmable function is activated The timeframe can be defined between 30 minutes and 24 hours.
Programme chart All weights marked with * are based on the weight of dry laundry. Cottons Max. load 8.0 kg* Items Cotton items such as those described under Cottons Normal with normal residual moisture. Notes Items are dried to a Normal level only. Cottons Max. load 8.0 kg* Extra dry, Normal Items Single and multi-layered cotton fabrics. For example: towelling, jerseywear, T-shirts, underwear, baby clothes, workwear, covers, aprons, jackets, bathrobes, and flannelette bed linen.
Programme chart Woollens handcare Max. load 2.0 kg* Items Woollen garments and fabric containing wool blends, e.g. pullovers, cardigans, stockings. Notes - Wool and wool blend items are only fluffed up; they are not dried completely. - Remove garments as soon as the programme has finished. Bed linen Max. load 4 kg* Extra dry, Normal, Hand iron, Machine iron Items Bed linen, pillow cases. MobileStart The Miele App is used for selecting programmes and operating the machine.
Programme chart Proofing Max. load 2.5 kg* Items Fabrics suitable for tumble drying, e.g. microfibre fabrics, skiwear, outerwear, fine, close-weave cotton garments (poplin), and tablecloths. Notes - This programme only dries to the Normal level. - This programme includes a proofing fixing phase. - Only use proofing agents which are stated by the manufacturer as being "suitable for use on membrane textiles". These agents contain fluorochemical compounds.
Changing the programme sequence Changing a programme after it has started It is no longer possible to change the selected programme. This prevents the appliance being operated unintentionally, e.g. by children. If you adjust the programme selector, the symbol will light up in the time display. The symbol goes out when you select the original programme. Cancelling the current programme Turn the programme selector to the position. The programme is cancelled. You can now select a new programme.
Condensed water container Emptying the condensed water container The condensed water is collected in the condensed water container. Empty the condensed water container after every drying programme. The indicator will light up when the maximum level in the condensed water container is reached. To turn the indicator light off: Open and close the door while the dryer is switched on. Damage to the door and the fascia panel when removing the condensed water container*.
Fragrance flacon FragranceDos Fragrance flacons (optional accessories) can be used to give your laundry a pleasant scent. Useful tip: You can simply close the fragrance flacon if you want to dry textiles without adding fragrance. Risk of fire and harm to health if fragrance flacons are used incorrectly. Leaked fragrance can be harmful to your health if it comes into contact with your body. Leaked fragrance can cause a fire.
Fragrance flacon Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper fluff filter next to the recessed grip. Markers and must line up with each other. Open the cover using the tab until the tab is right at the top as shown. Turn the outer ring clockwise a little. The fragrance flacon can slip out. Turn the outer ring so that markers and line up. Insert the fragrance flacon in the opening as far as it will go.
Fragrance flacon Opening the fragrance flacon Closing the fragrance flacon Before drying, you can select the intensity of the fragrance. After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. Turn the outer ring clockwise: the further you open the fragrance flacon, the more intense the fragrance. The fragrance is only released into the laundry effectively with damp laundry and longer drying times with sufficient heat transfer.
Fragrance flacon Removing/replacing the fragrance flacon Turn the outer ring anti-clockwise until markers a and b line up. Replace the fragrance flacon with a new one. When not in use, you can store the fragrance flacon in its original packaging. Fragrance flacons are available to order from Miele or via the Miele online shop. Fragrance can leak. Do not lay the fragrance flacon down.
Cleaning and care Fluff filters This tumble dryer has 2 fluff filters in the loading area of the door. Both fluff filters trap fluff produced during the drying process. Pull the upper fluff filter forwards to remove it. Clean the fluff filters after each drying programme. This prevents an extension of the programme duration. Also clean the fluff filters when the indicator light comes on. To make the indicator light go out, open and close the door while the tumble dryer is switched on.
Cleaning and care Remove the fluff from the filter surface of all the fluff filters and the perforated laundry deflector (see arrows). Turn the yellow dial on the lower fluff filter in the direction of the arrow (until you hear it click). Push the upper fluff filter back until it clicks into position. Close the door.
Cleaning and care Use a vacuum cleaner with a long crevice nozzle attached to remove any visible fluff from the upper air flow openings. Finally, clean the fluff filters with water. Cleaning the fluff filters with water Wipe the smooth plastic surfaces of the fluff filters with a damp cloth to clean them. Rinse the filters with warm running water. Shake the fluff filters thoroughly and then dry them carefully. Ensure the filters are dry before replacing them.
Cleaning and care Cleaning the plinth filter Clean the plinth filter whenever the indicator light comes on or when the programme duration is longer than usual. To make the indicator light go out, open and close the door while the tumble dryer is switched on. Removing the plinth filter Pull the plinth filter out by the handle. When the plinth filter is pulled out, the right guide pin will slide out. The guide pin prevents the flap from being closed without the plinth filter in place.
Cleaning and care Cleaning the plinth filter Pull the handle out of the plinth filter. Fit the plinth filter back on the handle the right way round. Clean the filter thoroughly under running water. Squeeze the plinth filter very carefully several times as you rinse it. Rinse the plinth filter until all visible residues have been removed. Use a damp cloth to remove any fluff from the handle. Damage caused by a damaged or worn filter.
Cleaning and care Cleaning the plinth filter flap Cleaning the dryer Disconnect the dryer from the electricity supply. Damage due to the use of unsuitable care products. Unsuitable care products could damage plastic surfaces and other parts. Do not use solvents, abrasive cleaners, glass cleaners or allpurpose cleaners. Use a damp cloth to remove any fluff. Make sure that you do not damage the rubber seal when doing this. Close the heat exchanger access panel.
Problem solving guide With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be remedied without contacting Miele. This will save you time and money because you won't need a service call. Please note that a call-out charge will be applied to unnecessary service visits where the problem could have been rectified as described in these operating instructions.
Problem solving guide Problem Possible cause and remedy The indicator light comes on. and continue to flash after a programme has been cancelled despite thorough cleaning. The plinth filter looks clean after thorough cleaning. However, the programme is terminated again and the error message appears again. There are probably still deeper residues which could not be removed. To deactivate the message, turn the programme selector to the position.
Problem solving guide Problem Possible cause and remedy and another number combination flash after a programme has been cancelled, a signal sounds. There is no obvious cause. Switch the dryer off and then on again. Start a programme. : lights up and the programme has been cancelled, a signal sounds. The laundry is unevenly distributed or has rolled up. Untangle the laundry and remove a few items, if necessary. Switch the dryer off and then on again. Start a programme.
Problem solving guide Unsatisfactory drying results Problem Possible cause and remedy The laundry is not sufficiently dry. The load consisted of different types of fabric. Finish drying using the Warm air/DryFresh programme. Select a more suitable programme next time. Useful tip: You can alter the drying levels for some programmes. See "Programmable functions", sections " Cottons drying levels", " Minimum iron drying levels".
Problem solving guide The drying process takes a long time. Problem Possible cause and remedy The drying process goes on for too long or even switches off.* The room in which the tumble dryer is located is too warm. Ventilate the room thoroughly. Detergent residues, hair and fine fluff can clog the filters. Clean the fluff filters and the plinth filter. Remove visible fluff from the heat exchanger. The laundry is unevenly distributed or has rolled up. The tumble dryer has been overloaded.
Problem solving guide Other problems Problem Possible cause and remedy There are humming noises. The compressor is operating. These noises are quite normal and do not indicate a fault. A programme cannot be There is no obvious cause. started. Connect the tumble dryer to the mains electricity supply Turn on the tumble dryer. Close the door. Check whether the mains fuse has tripped. Has there been a power cut? When power is restored, any previously running programme will restart automatically.
Problem solving guide Replacing the plinth filter Deformations The heat exchanger can clog up. Replace the plinth filter immediately (replacement filters are available as an optional accessory) if you see the following signs of wear before or after cleaning. Poor fit Deformations indicate that the filter has become worn. The edges of the plinth filter do not sit properly and the filter is deformed. Fluff will blow into the heat exchanger unfiltered through edges that do not sit properly.
Problem solving guide Cracks, tears, indentations Fluff will blow into the heat exchanger unfiltered through cracks and tears and will cause obstruction. This will eventually cause obstruction in the heat exchanger. White residues or residues of other colours Residues arise from laundry fibres and residual detergent components. They can be found on the front and side edges of the plinth filter. In extreme cases, they can form stubborn crusts.
Problem solving guide Regenerating the plinth filter Checking the heat exchanger You can regenerate one or more dirty plinth filters in the washing machine. The plinth filter will be ready for use again. Risk of injury from sharp cooling Before regenerating it, check whether the plinth filter is still in good condition. Check the plinth filter in accordance with the descriptions in "Problem solving guide - Replacing the plinth filter". If the plinth filter is worn, replace it.
Service Contact in case of fault Optional accessories In the event of any faults which you cannot remedy yourself, please contact Miele. Optional accessories for this tumble dryer are available from Miele (see contact details at the back of these instructions). You can book a Miele customer service call-out online at www.miele.com.au/service or www.miele.co.nz/service. Contact information for Miele can be found at the end of this booklet.
*INSTALLATION* Installation Front view a Mains connection cable b Control panel c Condensed water container – empty after every drying cycle d Door – do not open during drying 60 e Heat exchanger access panel – do not open during drying f Four height adjustable screw feet g Cool air intake grille – do not obstruct with a laundry basket or other objects h Hose for external drainage of condensed water
*INSTALLATION* Installation Rear view a Protruding lid for holding when moving the tumble dryer (see arrows) b Drain hose for condensed water c Hook for winding the mains cable around during transport d Mains connection cable Transporting the tumble dryer Danger of injury to people and damage to property caused by moving the appliance incorrectly. If the tumble dryer tips over, there is a danger of injury to people and damage to property. Ensure that the tumble dryer is stable during transportation.
*INSTALLATION* Installation Installation Levelling the dryer The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted. Make sure the dryer door can be opened without hindrance after installation. The screw feet can be adjusted to compensate for any unevenness in the floor.
*INSTALLATION* Installation Downtime after installation Damage to the tumble dryer by switching it on too soon. This can damage the heat pump. After setting up the tumble dryer, wait for at least one hour before switching it on. Ventilation The cool air intake at the front of the tumble dryer must not be blocked or covered. This would hinder a sufficient intake of cool air for the heat exchanger.
*INSTALLATION* Installation Additional installation requirements Suitable for pushing under a worktop This tumble dryer is suitable for pushing under a worktop. Appliance defect due to a build-up of heat. Make sure there is adequate room for warm air from the dryer to be directed away. - The appliance lid cannot be removed. - The electrical socket must be located in an accessible position near the appliance. - Drying durations may increase slightly.
*INSTALLATION* Installation Externally draining condensed water Notes When drying is in progress, condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer. The condensed water can also be drained away via the drain hose. The condensed water container will then not need to be emptied. Hose length: 1.49 m Maximum delivery head: 1.00 m Maximum drain hose length: 4.
*INSTALLATION* Installation Arranging the drain hose Examples Damage to the drain hose Drainage into a laundry tub or floor gully through incorrect handling. The drain hose can suffer damage and leak. Do not pull on the drain hose and do not stretch it or allow it to become kinked. Use the hose holder to secure the drain hose. There will be a small amount of residual water left in the drain hose. Have a container ready to collect this. Risk of water damage.
*INSTALLATION* Installation Direct connection to a sink drain outlet Use the hose holder, the hose clips and the non-return valve (available to purchase). Fit the adapter 1 to the sink drain outlet using the nut 2. The nut is usually fitted with a washer which must be removed. Attach the end of the hose 4 to the adapter 1. Use the hose holder. Use a screwdriver to tighten the hose clip 3 up close to the nut. Fit the non-return valve 5 to the tumble dryer drain hose 6.
*INSTALLATION* Installation Changing the door hinging You can change the door hinging on this tumble dryer yourself. For safety reasons, the tumble dryer must be disconnected from the electricity supply before changing the door hinging. You will need: - a T20 and T30 Torx screwdriver - a flat head screwdriver or pointed pliers Hold the door securely and pull it forwards: to remove the door you will need to pull the base plate of the hinge with its two pins out of the dryer.
*INSTALLATION* Installation Turn the door lock through 180°. Press the door lock into the openings on the opposite side of the door opening. 3. Remove the lock catch from the door First take the rubber seal off the door and place this to one side. Adjust the position of the door lock so that the screw holes line up with those in the front panel of the dryer . Secure the door lock with the two Torx screws. Use a T20 Torx screwdriver to remove the screw on the lock catch.
*INSTALLATION* Installation 4. Dismantle the door hinge from the door The door hinge cover must be unclipped from position and then removed. Remove the lock catch from the cover. This lock catch cover is no longer needed. However, please keep it in a safe place. Use a screwdriver to press down gently on position on the door hinge cover. Using a little force, pull out the door hinge cover . This door hinge cover is no longer needed. However, please keep it in a safe place.
*INSTALLATION* Installation 5. Change the door hinge on the door The door hinge is secured to the door with 2 angled rods. These rods need to be removed with a screwdriver or pointed pliers. Useful tip: In some circumstances, the rods can be difficult to dislodge. Moving the screwdriver with a levering action while pulling at the same time may help to work the rods free. Remove the door hinge and rotate it 180°. Refit the door hinge on the opposite side of the door.
*INSTALLATION* Installation You now need the new door hinge cover supplied with the tumble dryer. 6. Change the lock catch on the door You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch. Fit the new door hinge cover and clip it into position. Push the lock catch cover with its lock catch into position. Tighten the screw with a T20 Torx screwdriver.
*INSTALLATION* Installation Refitting Now that you have changed the 7. Refit the door door hinging, the door will open from the opposite side. Press the rubber seal back into the groove on the door. Position the door in front of the dryer. Fit the base of the door hinge with its two pins into the openings on the dryer. The base of the door hinge must be flush with the front panel of the dryer. The door cannot fall off in this position.
*INSTALLATION* Installation Electrical connection The tumble dryer is supplied with a mains cable with moulded plug ready for connection to a socket. The socket should be easily accessible after the tumble dryer has been installed. If the socket is not easily accessible, ensure that a suitable means of disconnection is provided on the installation side for each pole. Risk of fire from overheating. Connecting the tumble dryer to a multi-socket plug adapter or to an extension lead can overload the cable.
*INSTALLATION* Installation The data plate indicates the nominal power consumption and the connection data. Compare this information with the data of the on-site electrical connection. If in any doubt, consult a qualified electrician. Temporary or permanent operation with a self-sufficient or non-mains synchronous energy supply system (e.g. isolated networks, back-up systems) is possible.
Technical data Height 850 mm Width 596 mm Depth 643 mm Depth with door open 1077 mm Suitable for pushing under a worktop Yes Height for pushing under a worktop 850 mm (+8/-2 mm) Width for pushing under a worktop 600 mm Depth for pushing under a worktop 600 mm Suitable for stacking Yes Weight Approx. 62 kg Drum volume 120 l Maximum capacity 8.0 kg (weight of dry laundry) Capacity of condensed water container 4.8 l Drain hose length 1.49 m Maximum delivery head 1.
Consumption data Load Cottons Cottons Normal 1 Final spin speed in a Residual domestic washing moisture machine Energy Duration kg rpm % kWh min. 8.0 1,000 60 1.44 155 4.0 1,000 60 0.82 95 8.0 1,200 53 1.30 140 8.0 1,400 50 1.20 133 8.0 1,600 44 1.10 118 Cottons Normal incl. Gentle tumble 8.0 1,000 60 1.50 165 Cottons Hand iron 8.0 1,000 60 1.10 125 8.0 1,200 53 0.95 109 8.0 1,400 50 0.90 102 8.0 1,600 44 0.75 87 Minimum iron Normal 4.
Programmable functions Programming You can use the programmable functions to alter the dryer's electronics to suit your requirements. Programming is carried out by following these steps (, , ... ) using the sensors. Accessing the programming level Before you begin, ensure the following: - Make sure that the programme selector is turned to any of the programme settings. Choosing and selecting programmable functions The number of the programmable function will appear in the display as and a number: e.
Programmable functions Editing and saving the programmable function Confirm your selection with the Start/ Add laundry sensor. You can switch a programmable function on or off or select different options. The number of the programmable function, e.g. , will light up again. Exiting the programming level The programmable function option will appear in the time display as and a number: e.g. .
Programmable functions Cottons drying levels You can adjust the drying levels for the Cottons programme to one of 7 different levels. Options = even damper Cooling temperature The laundry will be cooled to 55 °C before the end of the programme. It can be cooled to a lower temperature, but this will prolong the cooling phase. The level is set in increments of 1 °C.
Programmable functions Keypad tone The tone that sounds when a sensor is pressed can be changed or switched off. Options = Off = Factory default setting = Louder PIN Code The code prevents your machine being used without your knowledge. When the code has been activated, you have to enter the code after switching the dryer on. Otherwise the dryer cannot be operated.
Programmable functions Conductivity This programmable function should only be altered if the water is so soft that it is likely to cause the electronics which sense residual moisture in the laundry to give false readings. Options = Off (factory setting) = low Important This programmable function should only be set if the water used for washing the laundry is extremely soft with a conductivity reading (electrical conductivity) of less than 150 μS/cm.
Programmable functions Memory You can set the following: The electronics will save the drying level and any options selected for the current drying programme. They will also save the duration of the Warm air/ DryFresh programme. The next time the programme is selected these saved settings will appear in the display. Options Buzzer is active The buzzer sounds to let you know the programme has finished. It can be switched on or off.
Programmable functions Airways indicator Fluff must be removed after every drying programme. In addition, this indicator will remind you to clean the filters when a certain amount of fluff has collected in them: You can decide at what level of fluff this reminder should be given. You will have an idea of how often this should be done after a few drying programmes. Options = Off does not light up.
Programmable functions Network The , and programmable functions are only displayed if the requirements for using Miele@home have been met (see “Miele@home” and “Before using for the first time”). Switching off Wi-Fi The network configuration should be reset whenever the dryer is being disposed of or sold, or if a used dryer is being put into operation.
Programmable functions Running a RemoteUpdate Information about the content and scope of an update is provided in the Miele App. The message will appear in the time display if an update is available. You can install the update immediately or postpone this until later. When the tumble dryer is switched on again, you will be reminded about the update. Deactivate RemoteUpdate if you do not want to install any updates. The update may take several minutes.
Programmable functions Remote control You can use the Miele App to check the status of your tumble dryer from anywhere and start it remotely. You can also control it remotely via the MobileStart programme. Remote control is automatically activated when you connect the tumble dryer to the Wi-Fi network. You can switch off remote control if you do not want to operate the tumble dryer with your mobile device. A programme can be cancelled via the App even if this programmable function is switched off.
Programmable functions Copyright and licences for the communication module For the purpose of operating and controlling the communication module, Miele uses proprietary or third-party software that is not covered by open source licensing terms. These items of software/software components are protected by copyright. The copyright powers of Miele and third parties must be respected. In addition, the communication module contains software components which are distributed under open source licensing terms.
Miele Australia Pty. Ltd.
TWD 660 WP en-AU, NZ M.-Nr.
