Operating instructions for condenser tumble dryer T 8432 C To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation! Rather than just throwing these materials away, please ensure they are offered for recycling.
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Guide to the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Features . . . . . . . . . . . . . . . . .
Contents Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Check and fault indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 After Sales service . . . . . . . . . . .
Warning and Safety instructions This tumble dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance. Keep these instructions in a safe place and ensure that new users are familiar with the content.
Warning and Safety instructions ~ The electrical safety of this tumble dryer can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested, and where there is any doubt the household wiring system should be inspected by a qualified electrician.
Warning and Safety instructions ~ The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way. ~ The dryer must not be used without the condenser unit in place. ~ The fluff filters must be thoroughly dried after cleaning. Damp or wet filters could cause operational faults. ~ Condensed water is not drinking water. It can cause health problems in both people and animals. ~ Always keep the area around the tumble dryer free of dust and fluff.
Warning and Safety instructions ~ To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: – fabrics which contain a large proportion of rubber, foam rubber or rubber-like materials. – items which contain damaged padding or fillings (e.g. pillows and jackets). If the filling comes out it could ignite and cause a fire. – items which have been treated with inflammable cleaning agents.
Guide to the machine Control panel a PROGRAMME buttons ewith indicator lights For selecting a drying programme. b Extra option buttons with indicator lights Various extra options can be added to the drying programmes. c Drying level button with indicator lights For selecting the drying level. g Start/Stop button For starting the programme selected and cancelling a programme once it has started.
Guide to the machine Features Buttons and check lights Display The relevant indicator light comes on each time a button is pressed. The display shows: – the programme duration (time remaining); – the delay start time; – check messages; – programmable functions. Estimated time remaining When a programme is selected the estimated duration (time remaining) will appear in the display.
Notes on laundry care Care symbols Before drying check the drying symbol on the care label. If there are no symbols, dry at your own risk! q . . . . . . . . . Dry at normal temperature r. . . . . . . . . . . . Dry at low temperature s . . . . . . . . . . . . . . . Do not tumble dry Tips on drying – Always observe the maximum recommended loads given in the "Programme chart". Never overload the drum.
How to dry correctly Brief instructions C Load the tumble dryer The headings numbered (A, B, C ...) show the operating sequence and can be used as a brief guide to using your dryer. ^ Press the Door button to open the door. ^ Load the laundry loosely into the drum. A Sort the laundry To ensure an even drying result separate out the washed laundry and sort it according to: . . . the drying level required . . . the type of fibre or weave . . . size . . . the moisture content after spinning.
How to dry correctly D Select a programme ^ You can change to another programme by pressing the e or button. – the appropriate programme indicator light will come on under Programme selection. – the Extra options or Drying level indicator lights will also come on. Automatic, Cottons, Minimum iron/Delicates, Shirts and Denim programmes ^ Press the button underneath Drying level repeatedly until the indicator light for the drying level you want lights up.
How to dry correctly E Select any extra options Selecting/deselecting Select the buzzer if wished A buzzer sounds (at intervals for a maximum of 1 hr) to let you know the programme has finished. The buzzer can be switched on or off even after a programme has started. The buzzer will still sound if there is a fault, even if it has been switched off. You can alter the pitch of the buzzer: ^ Select a programme.
How to dry correctly E Start the programme ^ Press the Start/Stop button. – The indicator light for the Start/Stop button will then change from flashing to being on constantly. – The programme duration will appear in the display. F Remove the laundry when the programme has finished The Anti-crease/Finish indicator light will come on to indicate that the programme has finished. The indicator light for the drying stage reached (depending on the programme selected) will also come on.
Extra options Short For drying fabrics which can withstand higher temperatures and fabrics with the q symbol on the care label. Do not use on minimum iron or delicate fabrics. – The programme duration is shorter. Cool air Select this option when you only want to air garments with cool air. – It is not possible to select a combination of the Low temperature, Short, Cool air options at the same time. – See the programme chart for details of the extra options which are suitable for a particular programme.
Delay start To select Delay start The start of a programme can be delayed by up to 24 hours (24^). After selecting a programme: ^ Press the Delay start button repeatedly until the required delay period shows in the display. – The Delay start indicator light will flash. – Times of: up to 10^ are selected in 30 minute steps more than 10^ in 1 hour steps While the delay start time is counting down, you can still add laundry to the drum: ^ To do this, first switch the dryer off and open the door.
Programme chart Max. load: 3.5 kg* Automatic Normal+, Normal, Hand iron r Fabric type Mixed loads of cotton and minimum iron fabrics. Sort according to colour. Extra option Anti-crease Cottons Extra dry, Normal+, Normal** Fabric type Max. load: 6 kg* Single and multi-layered cotton fabrics such as: e.g.: towelling, jerseywear, T-shirts, underwear. Notes – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for jersey fabrics (e.g.
Programme chart Woollens handcare Max. load: 2 kg* Fabric type Woollen fabrics Note – This programme only fluffs up woollen garments. They are not dried completely by this programme. – Remove garments as soon as the programme has finished and leave to finish drying at room temperature. Extra option Low temperature. (Low temperature cannot be deselected). Shirts Max. load: 2 kg* Normal+, Normal, Hand iron r Garment Shirts and blouses. Extra options Low temperature.
Changing the programme sequence Changing a programme while it is running You cannot change to another programme once a programme has started (this prevents unintentional alterations). It is still possible to select or deselect the Buzzer and the Anti-crease extra option. You will need to cancel the current programme before you can select a new one. Cancelling a programme ^ Press the Start/Stop button. The items will be cooled down, depending on the temperature reached and how long they have been dried for.
Electronic system lock To deactivate the lock The system lock prevents your machine being used without your knowledge. Before you begin, first ensure that: – The tumble dryer is switched off. It can be activated if wished. – The door is closed. The dryer's electronics are locked. The dryer can still be switched on but a programme cannot be started. The Locked indicator light will flash if an attempt is made to start a programme.
Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose (see "Installation"). Empty the condensed water container after every drying programme. The Container indicator light will come on if the maximum level of the condensed water container is reached. The indicator light will go out when the door is opened and closed again. ^ Open the shutter and empty out the water.
Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening. Clean the filters after each drying programme*. Cleaning them whilst dry Tip: You can also use a vacuum cleaner to remove the fluff. ^ Remove any fluff from the hollow part of the door opening.
Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water. ^ To remove the fluff filter from the door holder see previous page. ^ Place the filters back in the door opening (the left and right filters are identical) with the finger holders facing upwards. See illustration. Cleaning the tumble dryer Disconnect the machine from the mains electricity supply.
Cleaning and care Cleaning the condenser unit Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit. Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage. Check the condenser unit at least twice a year. Always check it if the Airways indicator light comes on. If the dryer is used frequently then check the condenser unit after approx. 100 drying cycles. Clean it if necessary.
Cleaning and care If you cannot see any fluff: ^ Replace the condenser unit (see following page). If you can see some fluff: ^ Clean the condenser unit as described below. Cleaning the condenser unit ^ When rinsing the condenser unit, make sure you position it as shown in the next two illustrations. ^ Pull the condenser unit out of its housing by the handle. Checking the condenser unit ^ Use a shower head or similar to rinse the unit out as shown. ^ Hold the condenser unit up to the light as shown.
Cleaning and care Replacing the condenser unit ^ With the handle facing upwards, push the condenser unit back into position in its housing. ^ Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove. When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove. ^ Then flush the unit through from the front.
Problem solving guide With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department. ,Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous.
Problem solving guide Problem Possible cause Remedy There is a build up of fluff. Fluff is principally the result of friction when garments are being worn and washed. Machine drying hardly causes any fluff to form and has been established by research institutes to have no appreciable effect on the lifetime of the garment. The load consisted of different fabrics. Fluff is collected by the fluff filters and can be easily removed (see "Cleaning and care"). The laundry is not sufficiently dry.
Problem solving guide Problem Possible cause Remedy The drying process Important: Before attempting to remedy one of the goes on too long or following causes, switch the dryer off and switch on again even switches off. to start the programme again. Ventilation to and from the Open a door or window while the machine is in dryer may be insufficient (e.g. because it is installed operation for increased air in a small room). This has flow. caused the temperature in the room to rise sharply.
Problem solving guide Problem Possible cause Remedy Water leaks from the machine after the condenser unit has been cleaned. – The inner cover of the – Ensure that the condenser unit has not condenser unit is been locked properly positioned correctly and/or the condenser and lock the inner unit has not been cover. positioned correctly. – Check the rubber seals. – Fluff has collected in the condenser unit – Use a cloth to remove housing. any visible fluff from the inside of the condenser unit housing.
Problem solving guide Check and fault indicator lights Problem The Airways indicator light comes on. Possible cause This indicator light comes on to warn you that the dryer is not working efficiently. Remedy Cleaning the fluff filters is usually all that is required. However, if the Airways indicator does not go out after you have cleaned them, then also check all the possible causes described under "The drying process goes on too long or even switches off".
Problem solving guide Problem Possible cause Remedy The programme This is not a fault. – Use the Warm air programme (timed drying) to dry stops and the The electronic unit has individual items. Anti-crease/Finish recognised that there indicator light is no laundry in the – The indicator light will go out comes on. when you open and close the drum and cancelled door, if the dryer is switched 0 appears in the the programme. display. on. Drying individual The buzzer sounds.
Problem solving guide Changing the lamp Disconnect the tumble dryer from the mains electricity supply. The lamp specification and maximum wattage is stated on the data plate and on the lamp cover. ^ Open the door. ^ Replace the lamp. You will find the interior lamp cover at the top of the drum aperture. ^ To close the cover push it upwards and press it on the left and right until you hear it click into position.
After Sales service In the event of any faults which you cannot remedy yourself, or if the appliance is under guarantee, please contact – your Miele dealer or – the Miele Service Department (see back cover for contact details). When contacting your dealer or the Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plate situated on the right hand side below the drum aperture.
Installation Front view a Mains connection cable e Service panel for condenser unit b Condensed water container f Four height-adjustable screw feet c Control panel g External drainage options (e.g. via wash basin, wash basin drain outlet, or gully).
Installation Rear view Building under a continous worktop / in a kitchen run ,A building-under kit* with a coverplate to replace the appliance lid is required. It must be fitted by a suitably qualified person to ensure electrical safety. N.B. If you wish to push your appliance under a worktop and there is space to do this without removing the lid the building under kit is not necessary. Otherwise the building under kit is essential.
Installation Levelling the tumble dryer Room in which the dryer is located Air taken in for use in the drying process will be warm when it is expelled from the front of the dryer. This expelled air heats up the air in the room. It is therefore very important to ensure that the room is adequately ventilated, particularly if the dryer is located in a small room. Otherwise running times and energy consumption could be increased.
Installation External condensed water outlet General notes ^ There will be a small amount of residual water in the drain hose. Have a container ready to collect this. When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the tumble dryer is installed near a sink, drain outlet etc. so that the condensed water container does not have to be emptied. Drain hose length . .
Installation External drainage via a sink or gully ^ See "Front view" illustration. ,If you want to drain the water off into a sink you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage. Example: Connection to a sink drain outlet The drain hose with non-return valve fitted can be connected directly to a suitable sink drain outlet.
Installation ^ Fit adapter 1 to the sink drain outlet using nut 2. If this nut has a flat disc in it you should take the disc out first. ^ Attach the end of the hose 4 to adapter 1. ^ Use a screwdriver to tighten hose clip 3 up close to the nut. ,The non-return valve 5 must only be fitted in an upright position or at a slight angle (see illustration). If it is fitted in a horizontal position it will not work correctly.
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained.
Consumption data Programme Load Final spin speed Energy Duration in a domestic washing machine kg* rpm kWh Minutes Cottons Normal 6.0 1000 (60 % residual moisture)** 1200 1400 1600 1800 3.30 3.00 2.85 2.55 2.50 89 81 78 70 69 Cottons Hand iron rr 6,0 1000 (60 % residual moisture)** 1200 1400 1600 1800 2.65 2.35 2.20 1.85 1.80 71 63 60 52 51 Minimum iron/Delicates Normal 3.0 1200 (40 % residual moisture)** 1.20 37 Minimum iron/Delicates Hand iron 3.0 1200 1.
Technical data Height 850 mm Height for building under 820 mm Width Depth 595 mm 580 mm Depth with door open Suitable for pushing under a worktop 1060 mm Yes Suitable for stacking Weight Yes 51 kg Drum volume Maximum capacity 111 litres 6 kg dry weight Capacity of condensed water container approx. 3.5 litres Drain hose length 1.5 m Maximum delivery head Maximum drain hose length 1.
Programmable functions for changing default settings The programmable functions are used to alter the tumble dryer´s electronics to suit changing requirements. Programmable functions can be altered at any time.
Programmable functions Altering the residual moisture level in the Cottons programme The machine is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier, it is possible to reduce the default residual moisture level in the Cottons programme. Please note that programme durations will be longer if this option is activated. Follow steps A to E to programme and store in memory. Before you begin, first ensure that: – The tumble dryer is switched off.
Programmable functions Altering the residual moisture level in the Minimum iron/Delicates programme The machine is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier, it is possible to reduce the default residual moisture level in the Minimum iron/Delicates programme. Please note that programme durations will be longer if this option is activated. Follow steps A to F to programme and store in memory.
Programmable functions Memory function The electronics will memorise the drying level and any extra options selected for the current drying programme. The Memory function – is activated when the machine is delivered. You can deactivate it if wished. – does not work if a programme is cancelled or if Delay start has been selected. Follow steps A to F to programme and store in memory. Before you begin, first ensure that: – The tumble dryer is switched off. – The door is closed.
Programmable functions Extending the cooling down time The cooling down phase which takes place before the end of a programme can be lengthened if required. This makes the garments easier to handle. The dryer is delivered with the extended cooling down time option deactivated. You can extend the cooling down time by 5 minutes or 10 minutes. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. B Press the I-On/0-Off button in.
Programmable functions Airways indicator Fluff should be removed after drying. The Airways indicator will remind you to clean the filters when a certain amount of fluff has collected in the filters. You can decide at what level of fluff this reminder should be given. You will have an idea of which of the four options to select after a few drying programmes. Follow steps A to F to programme and store in memory. Before you begin, first ensure that: – The tumble dryer is switched off. – The door is closed.
Programmable functions Keypad tone An audible tone sounds each time a button is pressed. The machine is delivered with the keypad tone deactivated. You can activate it if wished. Follow steps A to F to programme and store in memory. Before you begin, first ensure that: – The tumble dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. B Press the I-On/0-Off button in.
Alteration rights reserved/2007 M.-Nr.
