Operating instructions for the G 665 dishwasher To prevent accidents and reduce the risk of damaging the machine, read the Operating Manual before installing or using the machine. ö M.-Nr.
Contents Contents Guide to the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 View of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the filters in the wash cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the spray arms.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the drain pump and non-return valve. . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the water intake filter. . . . . . . . . . . . . . . . . . . . .
Guide to the appliance Guide to the appliance Miele dishwashers are available in two versions: 1. Integrated (“i”) dishwashers “i”- dishwashers are designed for installation under a continuous countertop. The control panel with its accessories is included with the “i”- dishwasher in a separate package for on-site installation. The front is designed to accept a custom made panel, matching the existing kitchen cabinets. Installation directions can be found in the Installation chapter. 2.
Guide to the appliance View of the machine 1.Upper spray arm (not visible) 9. Combination filter 2. Cutlery tray (if applicable) 10. Salt reservoir (if applicable) 3. Upper basket 11. Dual compartment detergent dispenser 4. Water feed tube for the middle spray arm 5. Middle spray arm 6. Water hardness selector 12. Rinse aid reservoir (with dosage selector) 13. Data plate 7. Lower spray arm 8. Four height adjustable levelling legs 6 Note: Cutlery and lower baskets not shown.
Guide to the appliance Control panel 14. Rinse aid indicator lamp 15. Door release 16. Child safety lock 17. Temperature selector knob 18.
IMPORTANT SAFETY INSTRUCTIONS Repairs should only be performed WARNING by qualified personnel. Disconnect When using your dishwasher, follow all basic safety precautions. This appliance conforms to all uniform safety codes and regulations. To avoid injury and machine damage, read the operating instructions carefully before using the dishwasher. This dishwasher is designed for household use only.
IMPORTANT SAFETY INSTRUCTIONS When loading items to be washed: – Load pointed items so that they are not likely to damage the door seal. – Load knives with the cutting edge down to reduce the risk of injuries. For dishwashers with visible heating element Do not touch the heating element during or immediately after use. Do not wash plastic items unless they are labeled “dishwasher safe” or the equivalent. For items not labeled, check the manufacturer’s recommendations.
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ AVERTISSEMENT Au moment d’utiliser votre lave-vaisselle, veuillez observer toutes les mesures de sécurité de base. Cet appareil électroménager est conforme à tous les règlements et codes sur la sécurité. Pour éviter de vous blesser et d’endommager l’appareil, veuillez lire soigneusement les instructions sur l’utilisation. N’utilisez le lave-vaiselle que pour laver la vaiselle.
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ Ne pas modifier les commandes. Ne pas boire l’eau du meuble de lavage. Au moment de remplir le lave-vaisselle : – Mettre les articles pointus de manière à ce qu’ils n’endommagent pas le seau étanche de la porte. – Mettre le tranchant des couteaux vers le bas afin de réduire les risques de blessure. Ne pas laver les articles en plastique à moins qu’ils n’indiquent “Va au lave-vaisselle” ou l’équivalent.
Caring for the environment Caring for the environment Disposal of the packing material. The cardboard box and packing material protects the appliance during shipping. It has been deliberately designed to be biodegradable and recyclable. Please dispose of these materials as you would any other recyclable products. Disposal of your old machine. Old machines contain materials which can be recycled. Please contact your local recycling center about the possibility of recycling these materials.
Before using for the first time Before using for the first time Before using for the first time, please note the following points. Setting the water softener (if applicable). The water softener must be set to correspond to the water hardness in your area. This can be obtained from your local water company, or by using a test kit that can be purchased from the Miele Parts Department. The salt reservoir must only be filled with water and salt. Never fill it with detergent. Adding rinse aid.
Opening and closing the door Opening and closing the door To open the door. Press the release catch inside the door grip. If the door is opened during operation, all functions will automatically be interrupted. Child safety lock. The child safety lock is designed to deter children from opening the dishwasher door. Use the provided key to turn the child safety lock to the desired setting. To close the door. Push the baskets in. Lift the door and push until it clicks into position.
Water softener (Not available in US models.) Water softener (Not available in US models.) The water softener must be set to corre- Setting the water hardness spond to the water hardness in your level. area. This can be obtained from your There are six settings on the selector, lolocal water company or by using a test cated on the right side of the wash kit that can be purchased from the cabinet: Miele Parts Department.
Water softener (Not available in US models.) Filling the salt reservoir. The salt reservoir should be filled before the first use and whenever the “Salt” indicator lamp is lit. Use water softener reactivation salt (1 - 4 mm grain size), as other salts may contain insoluble additives which can impair the functioning of the softener. The salt reservoir holds approx. 4 lbs (2 kg) of salt. Inadvertently filling the salt reservoir with dishwashing detergent will damage the water softener.
Water softener (Not available in US models.) Salt indicator. Bypassing the Salt indicator lamp. In order to bypass the salt indicator lamp, you will need a screwdriver and needle nose pliers. Remove the salt reservoir cap. When the salt reservoir is empty, the “Salt” indicator lamp will light, notifying you that the reservoir should be refilled with reactivation salt. Note: If your water is very soft (below 7 gr/gal), the salt indicator lamp will stay on.
Adding rinse aid Adding rinse aid The use of Rinse Aid is recommended to prevent spotting on dishes and glassware that normally occurs during the drying phase of automatic dishwashing. Adding rinse aid. Inadvertently filling the rinse aid reservoir with detergent will always damage the reservoir. Only pour liquid rinse aid formulated for residential dishwashers into the reservoir. Add Rinse Aid before the first use and anytime the “Rinse Aid” indicator lamp comes on.
Adding rinse aid Setting the dosage. Pour liquid rinse aid into the storage container until it is visible on the surface of the screen. Do not refill until the “Rinse aid” indicator lamp comes on. Only use rinse aid specifically labeled for residential dishwashers. Inadvertently adding detergent will damage the rinse aid dispenser. The dosage selector comes factory set to 3. It can be adjusted from 1 to 6, depending on your requirements. This setting dispenses approximately 3 ml rinse aid per program.
Loading the dishwasher Loading the dishwasher Load the dishes so that water can reach all surfaces. Do not place dishes and cutlery inside other pieces where they may be concealed. Hollow items such as cups and glasses should be inverted and placed in the upper basket. Concave based items should be placed at an angle so that water can run off them freely, or placed on top of the coffee bar (See page 25).
Loading the dishwasher Loading examples. Height limit Bottom basket. For larger and heavier items such as plates, serving platters, saucepans, and bowls. Depending on the dishwasher model, glasses can be cleaned in the bottom basket if a special glassware insert is installed. The height guard at the base of the upper basket is there to protect the middle spray arm. No object placed in the lower basket should stand higher than this guard. Upper basket. Dishwashers with cutlery tray.
Loading the dishwasher Cutlery Dishwashers with cutlery basket: Unsorted cutlery should be placed in the cutlery basket, with the sharp ends down. Place small spoons in the individual slots to either side of the cutlery basket. 22 Larger items like soup ladles, long knives and mixing spoons should be placed lying down across the front of the upper basket.
Loading the dishwasher Utensil Insert for the Cutlery Basket By ensuring that one piece of cutlery does not rest against another, the included Utensil Insert will optimize the cleaning of soiled spoons and forks. Place the utensil handles into the inserts, making sure that adjacent items do not touch. To use the inserts: Place one in front of and one behind the basket handle by pushing them down over the notches on the basket partition walls.
Loading the dishwasher Dishwasher with cutlery tray (Not applicable in US model.) To make unloading easier, cutlery can be grouped in zones, one for knives, one for forks, etc. Spoon heads should be placed so that water can run off them freely. Larger items like sauce ladles, cake slices, long knives and mixing spoons can be placed lengthwise in the trough in the center of the tray.
Loading the dishwasher Adjustable cup racks. Coffee bar. To make room for tall glasses, raise the rack. Lower it to double stack smaller items. To allow water to run off of the bottom of coffee mugs, place them at a slant on top of the coffee bar. The bar can also be used as a separator between two rows of glasses to protect them and keep them from leaning against each other. To stack wide items, flip the bar to the right.
Loading the dishwasher Adjusting the upper basket. (depending on model) The upper basket height is adjustable. If tall items of dishware are being washed, more room can be obtained by raising or lowering the upper basket. Depending on the setting of the upper basket, the following dishware dimensions can be accommodated: Dishwashers with cutlery tray Upper basket position Top Middle Bottom Upper basket diameter 6" (15.5 cm) 7" (17.5 cm) 7 1/2" (19.
Items not suitable for dishwashers Items not suitable for dishwashers – Cutlery with wooden handles. – Wooden cutting boards. – Glued items such as old knives with handles that are glued together around the shank of the blade. – Hand made craft items. – Copper or tin items. – Plastic items which are not heat resistant. Please note: – Silver or aluminum items may suffer some discoloration. – Aluminum parts (eg. oven hood grease filters) should not be cleaned using commercial or industrial detergents.
Adding detergent Adding detergent Use only powder detergents formulated for residential dishwashers. Do not use gels or liquid detergents. Generally, filling the dispenser with one to two tablespoons of detergent will be sufficient to ensure thorough cleaning. If dishes are extra dirty, or if the soil has been allowed to dry on the dishes before washing, a program utilizing a prewash cycle should be selected.
Choosing a program Choosing a program The wash program chosen should depend on the type of dishes and the degree of soiling. In most cases a NORMAL program will give excellent results. The available programs and some of their applications are listed in the Program Chart on the next two pages.
Program chart Program chart Program When to use Detergent containing chlorine1) Compart- Compartment ment I II (Pre-wash) (Wash cycle) chlorine free2) Compartment II (Wash cycle) Program NORMAL 55 °C/130 °F This program is for normal everyday loads. 20 % 80% 100 % NORMAL 65 °C/150 °F Same as NORMAL 55 °C/130 °F, but at a higher temperature. Use for stubborn dried on particles. Contains an additional pre-wash cycle. Use for heavily soiled dishes.
Program chart Program cycle 1. 2. Preliminary Pre-wash pre-wash Main wash Usage Interim Final rinse rinse Drying Duration Electric (kWh) Hot water connection (49 °C / 120 °F) Water Liters/ Gallons 4) Minutes (approx.) X X X X X 0.9 19.6 / 5.2 104 X X X X X 1.2 19.6 / 5.2 109 X X X X X X 0.9 24.5 / 6.5 109 X X X X X X 1.0 24.5 / 6.5 110 X X X X 0.8 5) 14.7 / 3.9 83 5) 0.06 5 / 1.
Operating the dishwasher Operating the dishwasher Turning on. Close the door. Open the water valve (if closed). If you turn the Program knob past your desired program by mistake: Turn the Temperature selector to “OFF”. Turn the program knob clockwise past the 12 o’clock position, until the desired program is reached. Select the temperature. The new program will start. Changing programs. Wash temperatures can be changed while a program is running, by turning the Temperature selector.
Operating the dishwasher Program sequence indication. Program interruption During the wash program, the program knob will move around the dial and show which section of the wash cycle has been reached. A program is interrupted as soon as the door is opened. If the door is closed again, the program will proceed from its previous position.
Unloading the dishwasher Unloading the dishwasher Dishes tend to break and chip easier when they are hot. Allow the dishes to cool down until they are comfortable enough to handle before unloading them. If the door is opened at the end of the drying cycle, the dishes will cool much faster. Unload the lower basket first, then the upper basket and cutlery tray (if so equipped). This will prevent water drops from the upper basket or cutlery tray from falling onto the dishes in the lower basket.
Cleaning and care Cleaning and care Cleaning the filters in the wash cabinet. The combination filter in the base of the wash cabinet should be regularly inspected and cleaned as necessary. Any broken glass or dishware should be removed immediately upon discovery. Use caution when cleaning the filters, non-return valve or drain pump, as glass or bone splinters may be caught in the bottom of the wash cabinet. Turn the handle counterclockwise to release the filters.
Cleaning and care Turn the combination filter over and open the coarse filter cover by pulling back on the locking tab. After cleaning, make sure that the coarse filter cover is properly locked in place. 36 Replace the combination filter so that it lies flat in the base of the wash cabinet. Secure it by turning the handle clockwise.
Cleaning and care Cleaning the spray arms. On rare occasions particles of food may get stuck in the spray arm jets. They can be easily cleaned as follows: Dishwashers with cutlery basket: Unscrew the upper spray arm. Dishwashers with cutlery tray: Pull out the cutlery tray. Push up on the upper spray arm to engage the tooth-wheel mechanism and then unscrew the spray arm.
Cleaning and care Cleaning the drain pump and non-return valve. Use caution when cleaning the filters, non-return valve or drain pump, as glass or bone splinters may be caught in the bottom of the wash cabinet. If the water in the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. To clean them: Remove the combination filter. Use a jug or bowl to scoop the water out of the wash cabinet. Tilt the locking clamp to the side.
Cleaning and care Cleaning the water intake filter. The water valve housing on the inlet hose contains electrical components and should not be immersed, or run through water. Cleaning the filter. Disconnect the dishwasher from the electrical supply (unplug it or shut off the circuit breaker). A filter is incorporated in the intake hose that is attached to the dishwasher’s main shutoff valve.
Cleaning and care Cleaning the wash cabinet. Generally the wash cabinet is selfcleaning, provided that the correct amount of dishwasher detergent is used. If lime scale or grease deposits form, they can be removed with a special dishwasher cleaner available from the Miele Parts Department. Cleaning the door and the door seal. Wipe the door seal with a damp cloth to remove any food particles. Food residue and drink spillage should be wiped from the sides of the dishwasher door.
Checking the water level Checking the water level Checking the water level. If the water pressure is less than 14.5 psi (1 bar), too little water may flow into the wash cabinet. To check the water level, open the water valve completely and run the RINSE & HOLD program once (without dishes), to bring water into the system. Start the RINSE & HOLD program again. After approximately 3 minutes, open the door and remove the lower basket from the machine.
Checking the water level Increasing the water intake time. Position the program knob vertically, then pull it off. Using a small screwdriver, turn the adjusting slot on the right hand side of the spindle carefully counterclockwise until it clicks into position. = Counterclockwise turn (increases water intake to 2 min.) = Clockwise turn (factory setting - 1 min.
Problem solving guide Problem solving guide With the aid of the following notes, minor problems can be easily corrected. If you are unable to correct the problem, please contact the Miele Service Department. Any work on the electrical components of the appliance should only be performed by a qualified and trained person in accordance with local and national regulations. Unauthorized repairs could be dangerous. Problems and possible causes. The dishwasher does not start. – The door is not properly closed.
Accessories Accessories Bottle holder. (depending on model) Glass insert for the upper basket: provides special support for long stemmed glassware. Decor panel kit (GDU): to change an “i” model into a “u” model dishwasher. Side mount brackets: For installing a dishwasher under Corian® or granite countertops. These and other accessories are available through your Dealer or the Miele Parts Department. A bottle holder (for milk or baby bottles) is available for use in the lower basket.
Installation instructions 45
Contents Contents Dishwasher installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. Installing the steam deflector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Installing the dishwasher under the countertop. . . . . . . . . . . . . . . . . . . . . . . . . 3. Installing the control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. Aligning the control panel with the drawer fronts. . . .
Dishwasher installation Dishwasher installation The “i” model dishwasher is designed for installation under a continuous countertop. A panel can be custom made for installation on the front of the dishwasher, assuring a perfect match with the kitchen cabinetry. Removing the leg extensions. The black leg extensions can be removed if necessary, to reduce the height of the machine to 32 1/4" – 33" (see Fig.).
Dishwasher installation 1. Installing the steam deflector – (if applicable). 2. Installing the dishwasher under the countertop. A stainless steel plate is supplied to protect the underside of the countertop against steam rising from the dishwasher when the door is opened. If the countertop is made of Corian®, granite, marble or other solid, waterproof material, the steam deflector should not be used.
Dishwasher installation Install the slides. Two slides are included and should be installed on the feet of the dishwasher before the machine is pushed under the countertop. This will allow the machine to slide easier, protect the floor, and allow adjustment of the rear leveling legs from the front of the machine. Push the machine into the opening, making sure the electrical cable and hoses can reach their connection points without being kinked.
Dishwasher installation Adjust the rear leveling legs to the required height. To raise the machine - turn clockwise. To lower the machine - turn counterclockwise. Several turns may be needed to set the correct height. A low speed electric or cordless screwdriver can also be used. Adjust the front leveling legs by pushing on the foot with a slotted screwdriver. Tipping the machine slightly, if possible, will make adjusting the front legs easier. Make sure the machine is level when adjustments are complete.
Dishwasher installation 3. Installing the control panel. The control panel and hardware is packaged separately from the dishwasher. It should be installed using the following procedure. If a GDU decor kit is being used, (to convert an “i” dishwasher to a “U” version), the spacer bars g must first be removed and stored for possible use in the future (See the separate instructions for installing the GDU decor kit). If the GDU kit is not being used, skip the following step.
Dishwasher installation 4. Aligning the control panel with the drawer fronts. Adjustment range from 4 1/2" control panel with(112 mm): out spacer bars, to 5 3/4" (145 mm): control panel with four spacer bars, to 6": (154 mm): using a fifth spacer bar (optional accessory). After adjusting the control panel height, cut off the plastic screw excess. The control panel can be aligned with the drawer fronts of the kitchen cabinets by adjusting the spacer bars.
Dishwasher installation 5. Installing the custom door panel. A custom door panel matching the kitchen cabinetry can be installed on the dishwasher by using the provided templates and bracket. Length: 19" - 23 3/4" (48.3 - 60.4 cm) Width: 23 1/2" (59.8 cm) Note: The maximum panel length is only applicable when no spacer bars are used. After panel installation, see Step 6 “Adjusting the door springs”.
Dishwasher installation Place the bracket on the back of the door panel and adjust it so that: – the lines you drew on the templates align with the upper edge of the door panel and; – the mounting bracket is centered (left to right) on the door panel. Slide the mounting bracket up or down until the oblong holes on the machine door align with the corresponding marks on the template (as shown in the left side of inset D.
Dishwasher installation If the adjacent cabinetry (or appliance) does not have drawers and alignment to a drawer line is impossible: Hang the bracket on the machine door, without the templates, and tighten the four locking screws on the edges of the door panel. Close the door. Measure the distance from the adjacent cabinet (or appliance) door bottom to the bottom of the mounting bracket (X). Using measurement (X), draw a line on the rear of the door panel (X) inches up from the bottom.
Dishwasher installation Once the door panel is positioned correctly : Open the dishwasher door. Tighten all the Torx screws on the edges of the dishwasher door. Use the provided caps to plug the locking screw access holes. Open the dishwasher door slightly. If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its recess a few inches.
Dishwasher installation 6. Adjusting the door springs. The door springs are adjusted correctly when a half opened door remains in that position when released. If the door drops down, the spring tension needs to be increased. If the door closes, the spring tension needs to decreased. 7. Securing the dishwasher to the countertop. To ensure the stability of the dishwasher, it must be attached to the countertop after it has been positioned.
Dishwasher installation For Corian® or granite countertops, fasten the dishwasher to the adjacent cabinets as follows: For openings greater than 23 5/8" (60 cm) wide: Open the dishwasher door and using flat head screws, secure the dishwasher to the countertop by screwing through both the mounting brackets and the steam deflector. Make certain that the white rubber seal located at the top, outer edge of the dishwasher is tight against the bottom of the countertop.
Dishwasher installation For openings exactly 23 5/8" (60 cm) wide: Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash chamber. Fasten the dishwasher to the adjacent cabinets using the supplied screws and bushings. Make sure a bushing is placed over the screw before inserting it into its mounting hole. Tighten the screws and replace the caps.
Dishwasher installation For kitchens utilizing the included plastic toekick Adjusting the toekick recess. The included toekick will fit without modification when: – The machine is set to its maximum height (legs fully extended), and – the toekick is recessed as far as possible (4 "). If the machine height is less than maximum, or if the toekick is recessed less than 4 ", the toekick must be shortened (see following page).
Dishwasher installation Trimming the toekick The toekick cannot be pushed back in. It must be unscrewed, so that the tension on the spring clips can be released. The brackets can then be pushed in, and the toekick re-attached. The rear of the toekick has two cutting lines. Carefully open the dishwasher door until it hits the toekick. Using the front lower edge of the door panel as a guide, draw a line across the toekick. Unscrew and remove the toekick.
Electrical connection Electrical connection It is the responsibility and obligation of the customer to ensure that the electrical and plumbing installation is carried out by a qualified installer in compliance with national and local codes and ordinances. Disconnect the appliance from the power supply before servicing the machine by pulling the plug or turning off the circuit breaker. Specifications. Power Supply: 120 VAC, 60 Hz Rated Load: 12.
Electrical connection Permanent Connection (Hard Wiring). For hard wiring, the power cord must be disconnected from the terminal box located at the lower left front of the dishwasher, behind the toekick and service panel. Pass the permanent power supply cable through the strain relief and secure it to the terminal box.
Plumbing Plumbing It is the responsibility and obligation of the customer to ensure that the electrical and plumbing installation is carried out by a qualified installer in compliance with national and local codes and ordinances. Hot water connection. New plumbing: To help protect your home, all dishwashers that carry the following blue and white sticker are designed to shut off the water and drain the wash chamber in the rare event of an internal water valve failure.
Plumbing Existing plumbing: If the standard 3/8" copper plumbing for a dishwasher already exists with a compression fitting and valve as pictured: Cut the 3/8" copper tubing after the valve. Do not, under any circumstances, cut the intake hose. If the hose is cut, the dishwasher will not work, you will have a water leak and you could be injured. If the hose is too long, coil it neatly and place it behind the machine.
Plumbing Drain system specifications: Drain connection: The machine comes equipped with: – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – A built-in swivel connector which allows the drain hose to be routed in any direction. – A built in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. – A built-in odor trap on the discharge side to prevent odors from entering the kitchen.
Plumbing Venting the drainage system Additional note. Only if the dishwasher drain hose is connected to a floor drain or to a drain pipe that is below the level of the lower baskets wheels, the drain must be vented; otherwise the water inside of the dishwasher may siphon out during the course of a wash program. Since all Miele dishwashers are equipped with an odor trap and non-return valve, the drain hose can be connected directly to the drain pipe as illustrated.
Technical Data Technical Data Height 32 1/4" (82 cm) adjustable to 34 7/8" (88.6 cm) Width 23 1/2" (59.8 cm) Width of opening 23 5/8" (60 cm) Depth 22 1/2" (57 cm) U and i models Depth with door open 45 1/2" (116 cm) U and i models Weight approx. 115 Ibs (52 kg) Voltage 110/120 V AC Rated load 12.5 A / 1500 W Fuse rating 15 A Water pressure 14.5 - 145 psi (1 - 10 bar) Hot water connection 120°F (49°C ) (max 140°F (60°C)) Drain height 3 ft (1 m) maximum Drain length 12 ft (3.
Alteration rights reserved (G665/G667/G668) /000 2498 These instructions are printed on 100% unbleached, recycled paper are completely Biodegradable.
