Operating and installation instructions Freezer To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Contents Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 How to save energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Switching on and off . . . . . . . . . . . . . . . .
Contents Switching off the ice/water dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Settings mode for the ice/water dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Automatic defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Laying the electrical cabling and the pipework for the mains water supply . . . . . 68 Door front dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Tools and accessories required . . . . . . . . . . . . . . . .
Description of the appliance Control panel for the freezer a Access sensor b Sensor for selecting the temperature in the freezer (X for colder; Y for warmer) c On/Off sensor for the Super freeze function d On/Off sensor for the ice/water dispenser e Sensor for switching off the temperature or door alarm (only visible when the alarm is sounding) f Reminder to change the water filter Control panel for the ice/water dispenser a On/Off sensor for the lighting d Sensor for crushed ice b Chilled water senso
Description of the appliance a Interior lighting b Door basket c Ice cube maker d Ice cube container e Cover for ice/water dispenser (to save energy) f Adjustable shelf g Control panel for the freezer 6 h Rocker switch for switching the whole appliance on and off i Freezer baskets j Water filter k Ice/water dispenser in the door l Control panel for the ice/water dispenser m Dispensing spout for ice/water n Drip tray cover with grille underneath it
Caring for the environment Disposing of the packaging materials Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials.
Warning and Safety instructions This appliance complies with all statutory safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time. They contain important information on installation, safety, use and maintenance.
Warning and Safety instructions ~ The appliance is not suitable for storing and keeping cool medicines, blood plasma, laboratory preparations or other such materials or products. Incorrect use of the appliance for such purposes can cause deterioration of the items stored. The appliance is also not suitable for use in areas susceptible to explosion. Miele cannot be held liable for any damage resulting from incorrect or improper use or operation.
Warning and Safety instructions Technical safety ~ The coolant system is tested for leaks. The appliance complies with statutory safety requirements and the appropriate EU guidelines. ~ This appliance contains the coolant Isobutane (R600a), a natural gas which is environmentally friendly. Although it is flammable, it does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has, however, led to a slight increase in the noise level of the appliance.
Warning and Safety instructions ~ The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building up. For every 8 g of coolant at least 1 m3 of room space is required. The amount of coolant in the appliance is stated on the data plate inside the appliance.
Warning and Safety instructions ~ A damaged appliance can be dangerous. Check the appliance for visible signs of damage. Do not use a damaged appliance. ~ For safety reasons, this appliance may only be used when it has been fully installed. ~ The appliance must be disconnected from the mains electricity supply during installation, maintenance and repair work.
Warning and Safety instructions ~ The ice cube maker is not suitable for connection to a hot water supply. ~ Before making plumbing connections, ensure that the machine is disconnected from the mains electrical supply. ~ Never tamper with the movable components on the ice cube maker, including the ice cube expulsion mechanism or the element on the ice cube maker. Danger of injury.
Warning and Safety instructions ~ Do not operate any electrical equipment (e.g. an electric ice-cream maker) inside the appliance. Danger of sparking and explosion. ~ Do not store cans or bottles containing carbonated drinks or liquids which could freeze in the freezer. The cans or bottles could explode, causing injury or damage. ~ When cooling drinks quickly in the freezer, make sure bottles are not left in for more than one hour; otherwise they could burst, causing injury or damage.
Warning and Safety instructions ~ Only use genuine original Miele accessories with this appliance. Using spare parts or accessories from other manufacturers will invalidate the guarantee, and Miele cannot accept liability. Cleaning and care ~ Do not use any oils or grease on the door seal, as these will cause the seal to deteriorate and become porous with time. ~ Do not use a steam cleaning appliance to clean or defrost this appliance. Steam could reach electrical components and cause a short circuit.
Warning and Safety instructions Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. This way you will prevent children from accidentally locking themselves in and endangering their lives. ~ Be careful not to damage any part of the pipework whilst awaiting disposal, e.g. by – puncturing the refrigerant channels in the evaporator, – bending any pipework, – scratching the surface coating. Leaking refrigerant can damage the eyes.
How to save energy Installation site / Maintenance Normal energy consumption Increased energy consumption In a ventilated room. In an enclosed, unventilated room. Protected from direct sunlight. In direct sunlight. Not near to a heat source (radiator, oven). Near to a heat source (radiator, oven). Where the ideal ambient room Where there is a high temperature is approx. 20 °C. ambient room temperature. Temperature setting Ventilation gaps uncovered and dusted regularly.
How to save energy Normal energy consumption Use Drawers, shelves and racks arranged as they were when the appliance was delivered. Putting the cover on the ice/water dispenser if the ice/water dispenser is not going to be used for some time. Using the appliance without the cover on the ice/water dispenser. Only open the door when necessary and for as short a time as possible. Store food in an organised way. Frequent opening of the door for long periods will cause a loss of coldness.
Switching on and off Before using for the first time ^ Clean the inside of the appliance and the accessories with lukewarm water and a little washing-up liquid, and then dry with a soft cloth. Important: To ensure the correct functioning of the appliance, let it stand for approx. 8 hours if it has been transported on its side to its final location before connecting it to the mains. Switching on ^ Open the appliance door.
Switching on and off You can now Further settings – adjust the temperature, or You can select further settings in settings mode and then select certain appliance functions and adjust their settings. The settings for the different functions are described in more detail in the relevant section of these instructions. – select the Super freeze function or – switch the ice/water dispenser on or off. Please refer to the relevant section for more information.
Switching on and off Switching the sensor tone on/off The tone which sounds each time a sensor is touched can be deactivated. ^ Touch the access sensor so that it is highlighted in yellow. ^ Take note of the position of the X sensor (but do not touch it!). ^ By touching the X sensor, you can now select whether the sensor tone is switched on or off: = 0: Sensor tone switched off = 1: Sensor tone switched on = –: Return to menu ^ After selecting a new setting, touch the access sensor to confirm your choice.
Switching on and off Switching off for longer periods of time If the appliance is not going to be used for a longer period of time, e.g. whilst on holiday: ^ switch the appliance off, ^ disconnect it from the mains. ^ turn off the stopcock to the water supply (a few hours before you switch off the appliance), ^ empty the ice cube container, ^ clean the appliance out and ^ replace the water filter and ^ leave the door ajar to air the appliance.
The correct temperature It is very important to set the correct temperature for storing food in the appliance. Micro-organisms will cause food which is not stored at the correct temperature to deteriorate rapidly. Temperature influences the growth rate of these micro-organisms. Reducing the temperature reduces their growth rate. To freeze fresh food and to store frozen food for a long time, a temperature of -18 °C is required. At this temperature the growth of micro-organisms is generally halted.
The correct temperature When you have adjusted the temperature, wait for approx. 6 hours if the appliance is not very full and for approx. 24 hours if the appliance is full before checking the temperature display, as it will take this long for the appliance to reach the temperature. If, after this time, the temperature is still too high or too low, you will need to adjust it again. Temperature (Fahrenheit/Celsius) Temperature range ^ Take note of the position of the X sensor (but do not touch it!).
The correct temperature ^ By touching the X sensor, you can now set the temperature to be displayed in Fahrenheit or Celsius. † 0: Temperature in Fahrenheit † 1: Temperature in Celsius † –: Return to menu Temperature display ^ After selecting a new setting, touch the access sensor to confirm your choice. The temperature display will flash if ^ Now touch the X sensor repeatedly until c appears in the display. The temperature display on the control panel always shows the required temperature.
Temperature and door alarm Your appliance has been fitted with a warning system which ensures that the temperature in the appliance cannot rise unnoticed and to avoid energy being wasted if the door is left open. Switching the temperature alarm off early If the noise disturbs you, you can switch the alarm off early if you wish. Activating the alarm system The alarm system is always active. It does not have to be switched on manually.
Temperature and door alarm Door alarm The alarm will sound if the door is left open for more than 5 minutes. The sensor for switching the temperature or door alarm off will also light up. The alarm will stop and the sensor for switching the temperature or door alarm off will go out as soon as the door is closed. Switching the door alarm off early If the noise disturbs you, you can switch the alarm off early if you wish. ^ Touch the sensor for switching the temperature or door alarm off.
Super freeze Super freeze Switching off Super freeze Switch on the Super freeze function before putting fresh food into the freezer. Depending on the amount of food placed in the freezer, the Super freeze function will switch off automatically after approx. 52 hours. The sensor is highlighted in white and the appliance continues running at normal power. This helps food to freeze quickly and retain its nutrients, vitamins, flavours and appearance.
Arranging the interior fittings Moving the shelves Moving the door basket The shelves can be adjusted according to the height of the food. The door basket can be moved or totally taken out for loading, unloading and for cleaning. ^ Hold the shelf on both sides and raise it slightly so that it can be lifted over the catches at the back. ^ Pull the shelf forwards. ^ Place the shelf at the required level, ensuring that it has engaged in the catches at the back. ^ Make sure that the shelf is on straight.
Arranging the interior fittings Freezer baskets The freezer baskets can also be removed for cleaning. ^ Pull the freezer basket out as far as it will go. There is a safety catch on the door opening side which needs to be turned to a horizontal position in order to remove the basket. ^ Use a screwdriver or similar to turn the slot in the head of the pin to a horizontal position a. ^ Raise the snap fittings on both sides b and lift the basket out.
Freezing and storing food Maximum freezing capacity Storing frozen food To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible, the maximum freezing capacity must not be exceeded. The maximum freezing capacity for freezing within a 24-hour period is given on the data plate: "Freezing capacity ....kg/24 hrs".
Freezing and storing food Home freezing Only freeze fresh food which is in a good condition. Hints on home freezing – The following types of food are suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, dairy products, pastry, leftovers, egg yolks, egg whites and a range of pre-cooked meals. – The following types of food are not suitable for freezing: Grapes, lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears.
Freezing and storing food ^ Make a note of the contents and the date of freezing on the packaging. Before placing food in the freezer ^ When freezing more than 2 kg of fresh food, switch on the Super freeze function some time before placing the food in the freezer (see "Super freeze"). This also helps to prevent food that is already in the freezer from starting to defrost.
Freezing and storing food Most vegetables can be cooked while still frozen. Just put straight into boiling water or hot fat. The cooking time is slightly less than that of fresh vegetables due to changes in the cell structure. Never re-freeze partially or fully defrosted food. Consume defrosted food as soon as possible as it will lose its nutritional value and spoil if left for too long. Defrosted food may only be re-frozen after it has been cooked.
Ice/water dispenser Rinsing the pipework The ice/water dispenser must be connected to the mains water supply (see "Mains water connection"). Use a suitable container to dispense water and ice cubes into. Danger of glass splinters. Do not hold your hand under the ice/water dispenser spout. Danger of injury. Before using the ice/water dispenser for the first time ^ Touch the access sensor to highlight it in yellow. ^ Touch the On/Off sensor for the ice/water dispenser to highlight it in yellow.
Ice/water dispenser This will activate the rinsing function: Approx. 6 litres of water will now be pumped through the pipework. You can interrupt the rinsing process at any time to allow you to empty the container by taking your finger off the sensor for chilled water. The sensor will continue to flash yellow while you empty the container. A beep will sound when the rinsing process is complete and the sensors in the ice/water dispenser control panel will now be highlighted in white.
Ice/water dispenser Ice cubes and crushed ice Discard the ice cubes produced during the first 24 hours and do not consume any chilled water or ice/crushed ice during this period, as the water will have been used to rinse through the pipework. This also applies when using the appliance again after not having used it for a while. Remember it can take up to 24 hours to produce the first ice cubes. ^ Place a suitable container underneath the ice/water dispenser spout.
Ice/water dispenser If the 0 sensor is flashing, the drip tray needs to be emptied and dispensing is stopped automatically. Mop out the drip tray with a sponge or cloth. If the appliance has been switched off for a long period of time, discard the chilled water and ice that is produced in the 24 hours after the appliance has been switched on again.
Ice/water dispenser Switching off the ice/water dispenser The appliance must be disconnected from the mains water supply a few hours before the ice/water dispenser is switched off. ^ Open the appliance door. The colour of the other sensors show whether the function associated with that sensor is switched on (yellow) or switched off (white): De-misting function Ice cube separation Keypad tone ^ Let go of both sensors.
Ice/water dispenser Ice cube separation Keypad tone To prevent the ice cubes and crushed ice from freezing together and blocking the dispensing spout, the spindle in the ice cube container moves at regular intervals to separate them. You can deactivate this function if the noise disturbs you. The tone which sounds each time a sensor is touched can be deactivated. The appliance is delivered with this function activated.
Automatic defrost This appliance is equipped with a "Frost free" system. The freezer defrosts automatically. The moisture generated by defrosting collects in the condensor and is automatically dissipated by the condensor from time to time. This automatic defrosting system enables the freezer to remain permanently ice-free, however the food stored in the freezer will not defrost.
Cleaning and care Make sure that water cannot get into the electronic unit or the lighting. Do not use a steam cleaner. Steam could reach electrical components and cause a short circuit. The data plate inside the appliance must not be removed. It contains information which is required in the event of a service call.
Cleaning and care Aluminium frames Remove any soiling immediately. If this is not done, it might become impossible to remove and could cause the surface to alter or discolour. Before cleaning ^ Switch the appliance off by pressing the On/Off rocker switch. The rocker switch is located on the right side, below the control panel. ^ Disconnect it from the mains. ^ Take any frozen food out of the appliance and store it in a cool place. ^ Take out any removable parts for cleaning.
Cleaning and care Drip tray The drip tray catches excess water. When the drip tray is full the 0 symbol in the ice/water dispenser control panel will flash and dispensing will stop. There are sensors in the drip tray which measure when the drip tray needs to be emptied. To avoid a build-up of odour, the drip tray should be cleaned every day. When the 0 symbol flashes, ^ remove the drip tray cover and the grille. ^ Mop out the drip tray using a sponge or tea towel and then clean it.
Problem solving guide Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. What to do if . . . . . . the appliance does not get cold. ^ Check whether the appliance has been switched on. If it is switched on, the access sensor will light up in the display.
Problem solving guide . . . the temperature display for the freezer shows -18 °C, even though I have selected a higher temperature? . . . the alarm sounds and the sensor for switching off the temperature or door alarm lights up or is flashing. This is not a fault. If the ice maker is switched on and the room temperature is less than +18 °C, the temperature is automatically set to -18 °C. This is to ensure trouble-free functioning of the ice cube maker. ^ The door is open, or . . .
Problem solving guide . . . the reminder to change the water filter indicator flashes red. ^ When the reminder to change the water filter flashes red, this indicates that the filter needs to be changed now. . . . the 0 symbol is flashing in the ice/water dispenser control panel. The ice/water dispenser drip tray is full. ^ Empty the drip tray. . . . the control panel has misted up. The heater element behind the control panel is switched off. . . .
Problem solving guide ^ Check that ice cubes are not frozen together in the ice cube container and that the dispenser is not blocked. It is important to empty the ice cube container regularly, particularly if you have not used any ice cubes for more than a week. Remember it can take up to 10 hours to produce the first ice cubes. . . . the ice/water dispenser is only producing small ice cubes.
Problem solving guide . . . water is pouring out of the appliance. ^ Close the stopcock immediately. ^ Check whether the water pipework inside the appliance is damaged. Call the Service Department. ^ Check whether there is sufficient water pressure. ^ Switch the appliance off by pressing the On/Off rocker switch to the right hand side underneath the control panel. ^ Disconnect the appliance from the mains electricity supply. Top lighting ^ Check whether the correct valve was fitted. . . .
Problem solving guide ^ Engage the lamp cover at the back, then pull it forward and click it into place at the front. Side lighting ^ Turn the lamp cover anti-clockwise to remove it. Do not touch halogen lamps with your bare fingers. Use a soft cloth when changing a halogen lamp. ^ Pull the defective halogen lamp out. ^ Fit the new lamp into the holder. The following type of halogen lamp is required: 5 W / 12 V / G 4 cap. ^ Replace the lamp cover, turning it clockwise as far as it will go.
Water filter The appliance is supplied with a standard water filter that filters mains water for making ice cubes. You can replace this with an active charcoal filter which improves the taste and smell of the ice cubes by removing chlorine and other substances from the mains water. Replacement water filters (standard and active charcoal) are available from Miele. To ensure the quality of the ice cubes remains high, it is essential to change the water filter regularly.
Water filter To change the water filter Air in the system can cause water to gush out and the filter to spring out when it is removed. Take great care, therefore, when changing the filter. ^ Remove the cap from the old filter cartridge (3). ^ Take the new filter cartridge from its packaging, and remove the protective cover. ^ Fit the cap on the new filter cartridge (4). ^ Press the cap in and turn it 180° in an anti-clockwise direction (1). ^ Remove the old filter cartridge (2).
Water filter Using an external water filter ^ After the filter has been changed, the reminder to change the filter will continue to flash in the display. Confirm that the filter has been changed. If an external water filter is installed in the household, please leave the standard (bypass) filter in the appliance. If you use an external water filter and therefore wish to deactivate the reminder to change the water filter, please contact the Miele Service Department.
Noises Normal noises What causes them Brrrrr ... A humming noise is made by the motor (compressor). This noise can get louder for brief periods when the motor switches on. Blubb, blubb ... A gurgling noise can be heard when coolant is circulating through the pipes. Click ... Clicking sounds are made when the thermostat switches the motor on and off. Sssrrrrr ... On multi-zone and frost-free appliances you can sometimes just hear the sound of the fan inside the appliance.
After Sales / Guarantee In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee please contact: – your Miele Dealer or Guarantee: U.K. In the U.K. the appliance is guaranteed for 2 years from the date of purchase. However, you must activate your cover by calling 0330 160 6640 or registering online at www.miele.co.uk. – the Miele Service Department. Guarantee: Other countries See end of this booklet for contact details.
Information for test institutes All tests must be carried out according to relevant standards and directives. In addition, the following information provided by the manufacturer must be observed: – Loading instructions, – Information contained in the Operating and installation instructions.
Mains water connection Notes on connecting to the mains water supply Connection to the mains water supply should only be carried out by a qualified and competent person. Disconnect the appliance from the mains electricity supply before connecting it to the mains water supply. Close the stopcock before connecting the water intake hose to the appliance. The water quality must conform to the requirements for drinking water in the country the appliance is being installed in.
Mains water connection The stopcock should be easily accessible after the appliance has been built in. Preparing for plumbing the appliance into the mains water supply Plumbing connections must be correctly in place before the appliance is built in. The appliance is only suitable for connection to a cold water supply, which – is connected directly to the fresh water supply, to guarantee circulation of water throughout the system.
Mains water connection Before using the appliance for the first time the water inlet pipe should be purged of air by a qualified and competent person. Appliances with an opening for feeding the hose through: – To do so the stainless steel hose should be filled as far as possible with water before being connected to the appliance. – Mop up any spillages with a cloth.
Mains water connection Fitting the stainless steel hose to the appliance When fitting the stainless steel hose, make sure that it is neither kinked nor damaged. ^ Remove cap (1) from the water connection at the front of the appliance. ^ Screw coupling nut (2) on stainless steel hose (3) onto the threaded union. ^ Ensure that all connections are watertight. ^ Turn on the stopcock slowly and check the whole water system for leaks.
Electrical connection Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). The appliance is supplied with a mains cable and moulded plug ready for connection to an a.c. single phase 220-240 V 50 Hz supply. Please ensure that the connection data quoted on the data plate match the household mains supply.
Installation advice Location This appliance should not be installed where it is exposed to direct sunlight or directly adjacent to a heat-producing appliance such as an oven or a radiator. The higher the ambient temperature of the room, the more energy the appliance requires to operate. The appliance should be installed in a dry, well-ventilated room.
Installation advice Safe operation of the appliance is only assured if it has been installed and connected in accordance with these operating and installation instructions. Warning! This appliance is very heavy and can tip forwards when the door is open. Keep the door shut until the appliance has been built in and secured within the building-in niche in accordance with these instructions. Due to the size and weight of the appliance, installation must be carried out by two people.
Installation advice Floor Adjoining furniture/units To ensure the safe installation of the appliance and to guarantee its correct functioning, the floor to the niche where the appliance is to be installed must be smooth and even. The appliance is screwed to the adjoining furniture/units to the side and above. For this reason, it is essential that all furniture/units be fixed to the ground and/or wall. It must be made from strong, rigid material.
Installation advice Side-by-side installation This appliance may be installed "side-by-side" with another suitable refrigerator or freezer. Installation with a partition wall using the side-by-side installation kit The partition wall must be at least 16 mm thick. A side-by-side installation kit, available from Miele, is required. Ask your dealer which appliances are suitable for side-by-side installation with this appliance.
Installation advice Appliance door dimensions (opening angle 115°) F 1472 Vi A B C D 525 mm Door front (max. 38 mm)* Door handle* 234 mm * The dimensions for the door fronts and handles will vary according to the individual kitchen. Miele recommends using the full door opening angle of 115° for this freezer.
Building-in dimensions Niche width A F 1472 Vi 457 mm – 460 mm 67
Building-in dimensions Laying the electrical cabling and the pipework for the mains water supply 68 Door front dimensions
Installation Other Due to the size and weight of the appliance, it is essential that installation is carried out by two people. – Step ladder – Sack barrow Tools and accessories required – Wooden beams (min. 75 mm x 100 mm) if required, to prevent tipping; length depends on width of building-in niche – Cordless screwdriver – Wood screws in various sizes – TX screwdriver (e.g.
Installation Stainless steel fronts Building into a peninsular run Stainless steel fronts and stainless steel look plinth grilles are available from your dealer or the Miele Spare Parts Department. When built into a peninsular run, the rear of the building-in niche must be fitted with a kitchen furniture panel.
Installation Aligning the building-in niche Checking the building-in niche – The building-in dimensions now need to be checked. – Check the position of the electrical and plumbing connections (see "Electrical connection" and "Mains water connection"). – Check that all surrounding furniture/units are securely fixed to the wall. – Check the surrounding furniture/units for possible clashes when opening doors.
Installation The appliance can be rolled along the floor using the wheels at the back. Preparing the niche ,Keep the door to the appliance closed until it is fixed inside the building-in niche. ^ Do not remove the installation aids from the appliance door. These will be required later when the appliance is installed in the building-in niche. ^ Check the appliance for damage during transportation.
Installation Anti-tipping mechanism The anti-tipping mechanism a supplied is used to secure the building-in niche b, to the wall, preventing the appliance from tipping forwards. Use two anti-tipping mechanisms for each appliance or four for each side-by-side pair of appliances. ^ Place the anti-tipping mechanisms a on the left- and right-hand sides of the building-in niche, leaving <10 mm distance to the side walls.
Installation An alternative anti-tipping mechanism The appliance can alternatively be secured with a wooden beam across the top of the appliance. If this method is used, then there must not be any gap between the appliance and the wooden beam. ^ Mark the position of the lower edge of the wooden beam on the rear wall of the building-in niche. ^ Select screws of a length depending on the thickness of the wood.
Installation Placing the appliance in the niche If you are installing two appliances side by side, now secure the appliances to one another (see the instructions for the side-by-side installation kit). ^ Unscrew the plinth facing. ^ Secure the cable to prevent it becoming caught: Tie a piece of string to the middle of the cable, and as the appliance is being pushed into the niche, pull the cable forward underneath the appliance b. ^ Push the appliance into the niche.
Installation Aligning the appliance ^ Align the appliance with neighbouring furniture fronts. ^ A mark is located on the appliance base. When adjusting the height, this mark needs to be aligned at 32 mm from the floor. Unscrew the feet until the mark on the base has reached 32 mm. The 32 mm mark is for aligning the appliance in a niche height of 2134 mm. Important: Adjust the feet only until the marking on the base has reached the 62 mm point (max. niche height 2164 mm).
Installation – If a wooden beam has been fitted above the appliance to prevent tipping, the appliance height needs to be adjusted to fit snuggly under the wooden beam. Securing the appliance in the niche ^ Pull out the lugs for the side fixing plates g. ^ Screw on the lugs for the side plates. ^ Screw the lugs for the fixing plates f into the furniture/units above the appliance. If it is not possible to secure the appliance above, it can be attached to the niche at the sides only.
Installation When installing two appliances side by side, the filler strips for the two appliances need to be joined together to form one long strip. ^ Open the appliance door. ^ Insert the joining peg from the side-by-side kit halfway into the channel in the filler strip for the left-hand appliance. ^ Then insert the free half of the joining peg into the channel on the other strip, and press the two strips together.
Installation Preparing the furniture front ^ Remove the door basket. ^ Open the appliance door as far as it will go. ^ Unscrew the installation aids l and the angle trim m from the appliance door. ^ Put the angle trim m and screws in a safe place - they will be required later. ^ Take the cover off the light contact switch. ^ Close the appliance door. ^ Measure gap X between the adjusting bar and the upper edge of the adjacent furniture front.
Installation – The fixing frame has several different types of holes to take account of a variety of furniture fronts. – When securing the frame, always screw into the strongest part of the furniture door. – To do this, select screws which are slightly shorter than the thickness of the furniture door. ^ Screw the appliance handle to the furniture door from the inside. ^ Mark gap X on the inside of the furniture front. ^ Similarly, locate and mark the midpoint Y on the furniture front.
Installation Securing and aligning the furniture door ^ Press the angle trim on both sides into the white plastic frame, and screw them down securely. Replacement screws for this can be found in the plastic bag marked with the letter E. ^ Screw the nuts o loosely onto the threaded bolts - but do not tighten yet. ^ Close the appliance door and check the distance between the door and neighbouring furniture doors. ^ Insert the angle trim as far as it will go into the spaces in the frame, as shown.
Installation Securing the covers ^ Fit the plastic cover strips to the sides of the appliance door, clicking them into the space between the appliance door and the furniture front, starting at the bottom and working up to the top. ^ Now attach the covers onto the retaining clips on both sides. In the case of side-by-side installation, the cover strips are only required on the outer side. ^ Fit the cover to the light contact switch so that it clicks into place as shown.
Installation Fitting the plinth facing Do not cover the vents in the plinth. This could result in damage to the appliance. ^ Trim the plinth facing to the required length and height (cut along the lower edge of the plinth facing where it touches the floor). Fitting the air separator The air separator in the bottom of the ventilation grille separates air entering the appliance from that leaving it. It also stops warm air flowing into the appliance, which would cause a short circuit.
Installation Aligning the ice/water dispenser If necessary the depth of the ice/water dispenser can be aligned to line up with the furniture front. Disconnect it from the mains. ^ Remove the drip tray cover and the grid. ^ Push back on the dispenser spout and then pull it downwards to remove it. ^ Loosen the screws in the back cover. ^ Pull the locking device up out of the drip tray.
Installation Once the drip tray has been removed you can align the position of the ice/water dispenser using the four metal strips. ^ Remove the rear cover. ^ Loosen the level sensors and carefully bend them upwards. ^ Loosen the screws in the four metal strips. ^ Then insert a screwdriver into one of the four slits and push the ice/water dispenser sideways until it is correctly aligned with the furniture front.
Installation Securing the ice/water dispenser frame The word "TOP" is marked on the rear of the frame at the top. With 19 mm thick furniture fronts: ^ Fit the frame onto the ice/water dispenser and press it firmly into position so that it sits evenly with the furniture front. With 38 mm thick furniture fronts: ^ Fit the secondary trim to the frame. ^ Fit the frame onto the ice/water dispenser and press it firmly into position so that it sits evenly with the furniture front.
United Kingdom Miele Co. Ltd. Fairacres, Marcham Road Abingdon, Oxon, OX14 1TW Customer Contact Centre Tel: 0330 160 6600 E-mail: mielecare@miele.co.uk Internet: www.miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive, Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Miele (Shanghai) Trading Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500, Fax: +86 21 6157 3511 E-mail: info@miele.
F 1472 Vi en - GB M.-Nr.