Operating and Installation Instructions Built-in Vacuum-Sealing Drawer To prevent accidents and machine damage, read these instructions before installation or use. en-US M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS ............................................................ 4 Caring for the environment .............................................................................. 12 Overview............................................................................................................. 13 Overview of the drawer ....................................................................................... 13 Standard accessories............................................
Contents MieleCare ...........................................................................................................
IMPORTANT SAFETY INSTRUCTIONS Please note that the vacuum-sealing drawer is referred to as the drawer in these operating instructions. This drawer conforms to current safety requirements. Improper use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using the appliance for the first time. They contain important notes on installation, safety, use and maintenance.
IMPORTANT SAFETY INSTRUCTIONS Appropriate use This drawer is intended for domestic use and use in other similar environments. The drawer is not intended for outdoor use. The drawer is only for domestic use to vacuum and seal food in vacuum bags intended for this purpose and to vacuum-seal food in vacuum-proof containers made of plastic or stainless steel. All other types of use are not permitted. Never vacuum-seal live food (e.g., mussels, seafood).
IMPORTANT SAFETY INSTRUCTIONS Safety with children Children under the age of 8 years must be kept away from the drawer unless they are constantly supervised. Be sure to supervise any children in the vicinity of the drawer, and do not let them play with it. The sealing bar becomes hot during operation. The weld seam of the vacuum bag is also heated to a very high temperature during the sealing process.
IMPORTANT SAFETY INSTRUCTIONS Technical safety Unauthorized installation, maintenance, and repairs can cause considerable danger for the user. Installation, maintenance, and repairs must only be carried out by a Miele authorized technician. A damaged drawer can be dangerous. Always check for visible signs of damage. Never use a damaged appliance. Pay attention to any damage or cracks to the glass lid or chamber seal. Damage to the glass lid can cause implosion.
IMPORTANT SAFETY INSTRUCTIONS For safety reasons, the drawer may only be used when it has been fully installed. This drawer may not be used in non-stationary locations (e.g. on a ship). Any contact with live connections or tampering with the electrical or mechanical components of the drawer will endanger your safety and may lead to appliance malfunctions. Do not open the casing of the drawer under any circumstances. Do not operate the drawer with wet hands or if you are in contact with water.
IMPORTANT SAFETY INSTRUCTIONS The drawer must be completely disconnected from the power supply during installation, maintenance and repair work. This can be ensured as follows: - The circuit breaker has tripped, or - The fuse of the electrical installation is completely removed, or - The plug (if present) is removed from the outlet. In the process, pull the plug not the cord. If the drawer is installed behind a cabinet panel (e.g.
IMPORTANT SAFETY INSTRUCTIONS Correct use Danger of burning. The sealing bar becomes hot during operation. The weld seam of the vacuum-sealing bag is also heated to a very high temperature during the sealing process. Do not touch the sealing bar or the seam immediately after the vacuum-sealing process. Fire hazard. Do not store any easily flammable substances and materials in the vicinity of the drawer. The maximum load capacity of the telescopic drawer rails is 55 lbs (15 kg).
IMPORTANT SAFETY INSTRUCTIONS Never insert the tubes attached to the drawer into any body orifices. Cleaning and maintenance Do not use a steam cleaner to clean the drawer. The steam may reach electrical components and cause a short circuit.
Caring for the environment Disposal of the packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of your old appliance Electrical and electronic appliances contain valuable materials.
Overview Overview of the drawer a Air filter cover (see “Installation”) d Push2open mechanism The drawer can be opened by pressb Glass lid with chamber seal ing lightly in the middle of the drawer Push down on the little black triangle front. to close the glass lid.
Overview Standard accessories Vacuum adapter 1 adapter for vacuum-sealing thirdparty containers 14
Controls and display Sensor buttons The sensors react to touch. Every touch on the sensors is confirmed by an audible tone.
Cleaning for the first time Please stick the extra data plate for the appliance, supplied with this documentation, in the space provided in the “After sales service, data plate, warranty” section of this booklet. Remove any protective foil and sales stickers. Stickers carrying safety or installation information and the data plate must not be removed. Cleaning the drawer for the first time Take all accessories out of the drawer. Take care not to damage the glass lid and the chamber seal.
Operation Suitable vacuum bags Only vacuum bags meeting the following material requirements are permitted for use: Important information on use Miele does not permit vacuum-sealing of glass containers. - Suitable for use with food - Only vacuum-seal food. - Suitable for freezing and cooking - Only use food that is fresh and in good condition.
Operation - Fill the vacuum bag to a maximum of ²/₃ with solid food or ¹/₃ with liquid. - For a perfect weld seam, make sure that the edge of the bag is dry and grease-free in the area of the seam. - Position the open edge of the bag parallel to the sealing bar so that the edge protrudes over the sealing bar by approx. ³/₄" (2 cm). - Take care not to cover the vacuum pump air intake valve with the bag. - Vacuum bags are for single use only.
Operation Using the vacuum levels There are 3 levels for vacuum sealing. The higher the vacuum level selected, the greater the vacuum. Vacuum level Intended use Packaging, portioning, and storing Suitable for - Food that is prone to squashing, e.g., lettuce, berries, or chips Marinating, tenderizing, sous-vide cooking, and freezing Suitable for - Food that is prone to squashing, e.g., tender fish fillets - Sauces and food with a high liquid content (≥ 1.8 ox (50 g)), e.g.
Operation Using the sealing levels There are 3 levels for sealing vacuum bags. The choice of sealing level depends on the material thickness of the bag: the thicker the bag, the higher the sealing level. Tip: The sealing bar will get progressively hotter when carrying out a number of consecutive vacuuming processes. You can use a lower sealing level after sealing a few bags.
Operation Risk of injury! Vacuuming and sealing bags Damage to the glass lid can cause implosion. Do not under any circumstances use the drawer if the glass lid is damaged. Fill the vacuum-sealing bag. Soiling and liquid must not be allowed to get on the sensors. Otherwise, the sensors will fail to react or switch on or off unintentionally. Do not damage the drawer! If liquid gets into the vacuum pump air intake valve during a vacuuming process, this can result in damage to the vacuum pump.
Operation After the vacuuming process Sealing the bag early An acoustic tone will sound. You can end the vacuuming process before reaching the selected vacuuming level and seal the bag early. Open the glass lid. Danger of burning! The sealing bar and weld seam are hot. Do not touch the sealing bar or the weld seam immediately after the vacuuming process. Remove the vacuum-sealing bag from the vacuum chamber.
Operation Risk of injury! Third-party glass containers can implode during vacuuming. Only use vacuum-proof containers made of plastic or stainless steel. Vacuum-sealing third-party containers The process for vacuuming a container ® from the caso vacuum container set is described below. ® We recommend caso container sets if you wish to use third-party containers. These containers can be connected to the drawer using the vacuum adapter supplied.
Operation Place the lid on the container and press it down. Open the drawer and the glass lid. If an excessive amount of bubbles form, you can cancel the vacuuming process by pressing the sensor (see “Canceling a vacuuming process”). After the vacuuming process c An acoustic tone will sound. OP E N b a Detach the connector from the container lid. Make sure that the closure of the lid is still turned to “seal” (closed). Remove the vacuum adapter from the vacuum pump air intake valve.
Operation After use Touch the sensor to switch the drawer off. Clean and dry the drawer and any accessories as described in “Cleaning and care”. Do not close the glass lid until the vacuum chamber is completely dry. Close the drawer. The last vacuum and sealing level selected is automatically activated the next time the drawer is switched on, and this is shown in the display. Canceling a vacuuming process You can cancel a vacuuming process at any time, e.g.
Cleaning and care Risk of injury! The steam from a steam cleaner could reach electrical components and cause a short circuit. Do not use a steam cleaner to clean the drawer. The use of unsuitable cleaning agents can cause the surfaces to discolor or alter. Only use cleaning agents designed for domestic use. All surfaces are susceptible to scratching. Scratches on glass surfaces could cause a breakage in certain circumstances. Remove any residual cleaning agent immediately.
Cleaning and care If soiling is left on for any length of time, it may become impossible to remove. Surfaces may suffer discoloration or damage. Soiling is best removed after each use. Cleaning the drawer front and glass lid Cleaning the vacuum adapter Clean the vacuum adapter with a clean sponge and a solution of hot water and liquid dish soap or a clean, damp microfiber cloth. Then dry the vacuum adapter thoroughly with a soft cloth. Do not use the vacuum adapter again until it is completely dry.
Cleaning and care Completing a drying cycle When food is vacuumed, moisture gets into the oil circulation system in the vacuum pump. To remove the moisture, it is necessary to run a drying cycle after a particular operating period. The sensor on the control panel of the drawer lights up yellow when a drying cycle needs to be carried out. You can still run another 10 vacuuming processes after it lights up for the first time. After that, the sensor lights up red and a drying cycle must be carried out.
Frequently Asked Questions With the help of the following guide minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. This guide may help you to find the reason for the fault, and how to correct it. Problem Possible cause and solution The drawer will not open. The safety screws on the back of the drawer have not been removed. Contact Miele Technical Service. The drawer cannot be switched on.
Frequently Asked Questions Problem Possible cause and solution The vacuum-sealing bag was not sealed in time. The required vacuum (vacuum level 1) for sealing a bag was not achieved. Touch the sensor again or repeatedly until the vacuuming process ends and the bag is sealed. All sensors have gone out. The glass lid will not open. There was an interruption to the power supply during the vacuuming process. The vacuum chamber is still under pressure so the glass lid cannot be opened.
Frequently Asked Questions Problem Possible cause and solution The seal was not strong The edge of the bag is dirty (inside and out). For a enough and has perfect weld seam, the edge of the bag must be dry opened. and grease-free in the area of the seam. Fold the edges of the vacuum-sealing bag outward for filling. This will give you a clean, perfect weld seam. The edge of the bag was not positioned smoothly and without creases on the sealing bar.
Frequently Asked Questions Problem Possible cause and solution The weld seam is defective or not properly sealed in one or more places. The sealing bar and/or counterpressure bar are dirty or there are liquid residues on the sealing bar. Clean and dry the sealing bar and/or counterpressure bar. The rubber on the counterpressure bar is not evenly fitted. Flatten the rubber. The edge of the bag is dirty (inside and out).
Frequently Asked Questions Problem Possible cause and solution There is a film of oil on the glass lid and in the drawer. The oil in the vacuum pump has become extremely hot. Clean the drawer and leave it to cool down for 1 hour before starting another vacuuming process. When carrying out a number of consecutive vacuuming processes, wait a minimum of 2 minutes between each process to prevent the oil from overheating again. If the fault occurs again, contact Miele Technical Service.
IMPORTANT SAFETY INSTRUCTIONS - INSTALLATION WARNING - Read all instructions before installation or use of the drawer to prevent injury and machine damage. Before connecting the drawer to the line power supply, ensure that the connection data on the data plate (voltage and frequency) match the line power. This data must correspond in order to avoid the risk of damage to the drawer. Consult a qualified electrician if in any doubt.
Instructions for installation When integrating the drawer with a combination appliance, the combination appliance is placed on top of the drawer without the need for an interim shelf. All dimensions in this instruction booklet are given in mm and inches. Note to the installer: Please leave these instructions with the consumer of the appliance for the local building inspectors use. SAVE THESE INSTRUCTIONS.
Installation dimensions Installation in a base unit Installation in a tall unit a 13/8" (35 m m) " 7/8 0 2510 mm) 219 (5 48 1/8 (3 (4 mm ) mm" ) 3/1 6" m /1 6" m b ) 5 1/4" 5 9/16" (142 mm) " 3/8 2 ) 6" - 2 8 mm 1 / 1 56 220 mm (56 " 6 9/1 ) 5 1 mm (14 8" 1/ ) 2137 mm (5 " 16 ) m 7/ 23 5 m 9 (5 (22 7/8 */2 3* " *m m) a Cut-out for ventilation a Cut-out for ventilation b Installation dimensions with plug Power cord, L = 7' 2" (2,200 mm) b Installation dimensions with plug
Installation dimensions EVS with H 6xxx B(P) 13/8" (35 m m) a 7/8" /23* *m m) 217/8 " " 1/8 ) 217 mm 3 (5 21 9 (5 48 1 ( /8 3m (4 m m) 5 1/4" 6" 7/1 ) m 2395 m (5 " m m) 3/1 6" /1 6" m ) b 23 7/ 95 (5 (2 2* " 16 (05 50 6" 1/1 /8" (5668 m -5 6" 7/1 m) 23595 m ) 1 7/8 /2 3* * ) 3 2-222 m 0 m m) m m (3 /8" mm ) " m m ) a Ventilation cut-out required when installed in combination with a Self Clean oven b Installation dimensions including power cord plug connector Po
Installation dimensions m) (22* * mm 21 7/8 (05 17 15/16" (455,5 mm) 6" 7/1 m) 23595 m ( " 1/8 ) m m 37 (5 (4 mm ) 3/1 6" (5 22- 22 m 0 m m) (56568 m - 48 m 95 m ) ( b (141 mm) " 16 ) m m 7/8 */2 3* (3 m " 1/8 ) 2137 mm (5 21 9 (5 48 1/8 " " m ) mm ) 3/1 ) 6" 23 /1 6" m m ) m (4 *m mm ) 6" 7/1 m) (5 (2 2 (550 23595 m 7/ 23 16 " 215/8" ) 6" 1/1 3/8" 5 9/16" 219/ " mm 21 5 9/16" (141 mm) 1 (3 /8" mm ) 50 m) 6" 9/1 21 mm) 8 (54 (134 mm) 6" 1/1
Installation dimensions EVS with DGC 6x6x a 19/16" (40 m m) (22* mm ) 21 7/8 6" 7/1 ) m 2395 m (5 (5 1 (4 (3 /8" mm ) mm ) 3/1 6" 23 16 48 " m m ) " 1/8 " 16 7/ ) m 1 7/8 /2 3* (4 " *m m ) (3 /8" mm ) mm ) 3/1 6" ) 2137 mm (5 219 (5 m 95 2* 17 15/16" 6" 7/1 m) 23(595 m (5 (2 b (56568 m - 5 9/16" 219/ ) 6" " 1/1 8 3/ 22- 22 m 0 m m) (141 mm) 5 9/16" (141 mm) " 1/8 ) m m 21 7 3 (5 " mm (455,5 mm) 23 1/4" 0 m m) (56568 m - 50 (593 mm - 595 mm) (596
*INSTALLATION* Installation Do not damage the drawer! The drawer has an integrated vacuum pump, which contains oil. To prevent oil from leaking out, the drawer must be transported and stored in a horizontal position only. Do not tilt the drawer and do not stand it up on its side. Fitting the air filter and removing the safety screws Preparing the drawer For safe transportation, the vacuum pump is provided with a transit device which must be removed before installation.
*INSTALLATION* Installation Screw the air filter onto the vacuum pump using a screwdriver. Remove the safety screws from the back of the drawer. Do not damage the drawer! Remove the air filter before transporting the drawer and plug the vacuum pump with the transit device . To remove the air filter and fit the transit device, carry out these steps in reverse order. Fix the transit device to the back of the drawer. Slide the cover over the opening to close it.
*INSTALLATION* Installation 42
*INSTALLATION* Installation Integrating the drawer Fitting the anti-tipping mechanism Risk of injury! The drawer is heavy and will tip forwards when open. Installation must be carried out by two people. Keep the drawer closed until the anti-tipping mechanism supplied has been fitted to the side walls of the housing unit. Check that the base that the drawer will sit on is clean and level (use a spirit level). This is important for the appliance to function correctly.
*INSTALLATION* Installation Integrating and connecting the drawer Check that the air filter is fitted and the safety screws have been removed from the back of the drawer (see “Preparing the drawer”). Connect the line power connection cord to the drawer. Slide the closed drawer into the housing unit. When doing so make sure that the line power cord does not get trapped or damaged. Align the drawer at right angles.
*INSTALLATION* Installation Aligning the front of the drawer After integrating the combination appliance, it may be necessary under certain circumstances to align the front of the drawer and adjust the gap between the drawer and the combination appliance. To help you do this, there are 2 screws behind the drawer front with which the front is fixed to the drawer housing. Open the drawer. Loosen fixing screws on the right and left of the drawer housing. Danger of injury.
*INSTALLATION* Electrical connection ATTENTION: Installer: Before installation or servicing, disconnect the power supply by either removing the fuse, manually “tripping” the circuit breaker or unplugging the appliance. Pull the plug not the cord. Please leave these instructions with the customer. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible.
*INSTALLATION* Electrical connection Disconnecting from the power supply Danger of electric shock. After disconnection, ensure the appliance cannot be switched back on by mistake. The drawer must be completely disconnected from the power supply during installation, maintenance and repair work. This can be ensured as follows: - The circuit breaker has tripped, or - The fuse of the electrical installation is completely removed, or - The plug (if present) is removed from the outlet.
Customer Service Contact in the event of a fault In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Customer Service. You can book a Miele Service Call online at www.miele.com/service. Contact information for Miele Customer Service can be found at the end of this document. Please quote the model identifier and serial number of your appliance (SN) when contacting Miele Customer Service. Both pieces of information can be found on the data plate.
MieleCare This service is available in USA only. MieleCare, our Extended Service Contract program, gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability, and longevity of your Miele appliance.
Please have the model and serial number of your appliance available when contacting Customer Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Princeton, NJ 08540 Phone: 800-843-7231 609-419-4298 Fax: www.mieleusa.com Customer Service & Support Phone: 888-99-MIELE(64353) 888-586-8056 Fax: service@mieleusa.com International Headquarters Miele & Cie.
EVS 6114 en-US M.-Nr.
