Bruksanvisning

ManualsBrandsMiele ManualsSlimline HoodMiele DAS 4620 Slimline hette

12062340-01

Installation

*INSTALLATION*

Before installation

 Before installation, it is important

to read the information given on the

following pages as well as the

“Warning and Safety instructions” at

the beginning of this booklet.

Installation recommendations

- To achieve optimum vapour

extraction, the cooker hood must be

positioned centrally over the hob, not

to the side.

- The hob should be no wider than the

cooker hood, and if possible, it

should be narrower.

- The installation area must be easily

accessible. The cooker hood should

be easily accessible and easy to

dismantle in the event that service is

required. This should be taken into

consideration when planning the

position of cupboards, shelves,

ceilings or features in the vicinity of

the cooker hood.

Installation materials

1vent connection

for exhaust ducting 150mm.

1 non-return flap

for fitting into the exhaust socket on

the motor unit (not needed for

recirculation mode). Depending on the

model, the non-return flap may already

be fitted.

4mounting plates

for installation in a 600mm wide

cabinet

2 brackets

for installation in a 900mm wide

cabinet (only for 900mm wide

appliances)

2spring clips

for installation in a 900mm wide

cabinet (only for 900mm wide

appliances)

1spacer strip

for concealing the gap between the

rear of the appliance and the wall

Summary of content (10 pages)

PAGE 1
*INSTALLATION* 12062340-01 Installation Before installation  Before installation, it is important to read the information given on the following pages as well as the “Warning and Safety instructions” at the beginning of this booklet. Installation recommendations 1 non-return flap for fitting into the exhaust socket on the motor unit (not needed for recirculation mode). Depending on the model, the non-return flap may already be fitted.
PAGE 2
*INSTALLATION* 12062340-01 11839970 Installation 4 screws, M4 x 8 mm 4 (8)* screws, 4 x 15 mm DML 2000 installation kit for installing a hinged front panel to match kitchen furniture units (not supplied; available as an optional accessory) Installation materials for recirculation mode 4 screws, 4 x 30 mm You need the following optional accessories for recirculation mode: 8 (12)* screws, 4 x 15 mm 4 screws, M4 x 12 mm* DFKS 31-x installation kit contains 2 holders and 2 charcoal filters (DFKS 31-P
PAGE 3
*INSTALLATION* 12062340-01 Installation Appliance dimensions Dia. 1: DAS 4620 in a 600 mm wide cabinet.
PAGE 4
*INSTALLATION* 12062340-01 Installation Dia. 2: DAS 4920 in a 900 mm wide cabinet.
PAGE 5
*INSTALLATION* 12062340-01 Installation Dia. 3: DAS 4920 in a 900 mm wide cabinet or in a 900 mm wide cabinet with side compartments. The drawing is not to scale See diagram 1 for side view Footnotes for diagrams 1 to 3: a The front section of the cabinet must be fitted with a base panel to secure the cooker hood. b If a partition wall is to be provided in the cabinet, it must be removable.
PAGE 6
*INSTALLATION* 12062340-01 Installation Safety distance between hob and cooker hood (S) When planning the installation height of your cooker hood, the minimum safety distance between the top of a cooker or hob and the bottom of the cooker hood is as follows, unless a greater distance is specified by the manufacturer of your cooking appliance. See “Warning and Safety” instructions for further information.
PAGE 7
*INSTALLATION* 12062340-01 Installation Connection for air extraction  If the cooker hood is used at the same time as a heating appliance that relies on oxygen from the same room, there is a risk in certain circumstances of toxic fumes building up. It is essential that the “Warning and Safety” instructions are observed. The cooker hood should be installed according to local and national building regulations. Seek approval from the building inspector where necessary.
PAGE 8
*INSTALLATION* 12062340-01 Installation Non-return flap  Use a non-return flap in the exhaust system. A non-return flap ensures that when the cooker hood is not in operation, the duct is closed to prevent unwanted exchange of room air and outside air. If the exhaust is ducted through an outside wall, a Miele wall vent or roof vent (available as an optional accessory) is recommended. Both of these have a built-in non-return flap.
PAGE 9
*INSTALLATION* 12062340-01 Installation Silencer To reduce noise levels even further, a silencer (optional accessory) can be installed in the exhaust ducting. In extraction mode, the silencer not only reduces noise from the fan outside the house, but also sounds originating outside reaching the kitchen through the exhaust ducting (e.g. traffic noise). For this reason, the silencer must be positioned as close as possible to the ducting exit .
PAGE 10
*INSTALLATION* 12062340-01 Installation Electrical connection The cooker hood is supplied with a mains cable with moulded plug ready for connection to a suitable earthed socket. If the socket is not easily accessible or a fixed connection is envisaged, ensure that a suitable means of disconnection is provided on the installation side for each pole.  Risk of fire from overheating. Connecting the cooker hood to multi-socket adapters or extension cables can overload the cables.