Midea Cooker Hood Instructions MODEL: MHC60GSS MHC90GSS SAVE THESE INSTRUCTIONS CAREFULLY Read the instructions carefully before using your cooker hood, and keep them carefully. If you follow the instructions, your cooker hood will serve you many years well.
RECOMMENDATIONS AND SUGGESTIONS The instructions apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your appliance. INSTALLATION ●● The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. ●● The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the cooker hood.
COMPONENTS Ref. Qty. Product Components 1 1 Hood Body, complete with Control, Light, Blower, Filter. 2.1 1 Lower Decorative Chimney 2.2 1 Upper Decorative Chimney 4 1 Exhaust Pipe 5 2 Activated Charcoal Filter (optional) 2.2 4 3 2.1 5 Ref. Qty.
COMPONENTS 600/900 391 500 282 401 322 448 Min. 650mm 500 282 322 448 500 600/900 4 min. 448 max. 828 Min.
INSTALLATION WALL DRILLING AND BRACKET FIXING As the first step, proceed with the following drawings: ●● A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted. ●● A horizontal line A at 1083-1183 mm above the cooker top. ●● A horizontal line B at 30-377 mm above the horizontal line A. ●● A horizontal line C at 118 mm below the horizontal line A.
●● ●● Mark a point (3) on the horizontal line C, 80 mm to the vertical reference line. Repeat this operation on the other side, checking that the two marks are on one horizontal line. Mark a point (3) on the horizontal line C, 80 mm to the vertical reference line. Repeat this operation on the other side , checking that the two marks are leveled. Fix the brackets (optional): ●● Drill holes at the marked points with a ɸ10 mm drill bit.
CHIMNEY ASSEMBLY The chimney can only be installed with an exhausting hood. Lower decorative chimney ●● Fix the chimney fixing bracket 21 onto the lower decorative chimney with 2 screws 12 (4.2 x 9.5) supplied with the hood. 21 2.1 12 Upper Decorative Chimney ●● Slightly widen the two sides of the upper chimney and hook them between the wall and the bracket 21 which is fixed on the lower decorative chimney. ●● Fix the upper chimney onto the bracket 21 with 2 screws 12 (4.2 x 9.5) supplied with the hood.
USE MOTOR OFF SWITCH: Press this switch to stop the motor. SPEED SWITCH: Press this switch, and the motor runs at LOW speed. SPEED SWITCH: Press this switch, and the motor runs at MEDIUM speed. SPEED SWITCH: Press this switch, and the motor runs at HIGH speed. LIGHT ON/OFF SWITCH: Press this switch to turn on the light, and press again to turn it off.
MAINTENANC GREASE FILTER METAL SELF-SUPPORTING GREASE FILTER CLEANING ●● The filters must be cleaned every 2 months of operation or more frequently for particularly heavy usage, and can be washed in a dishwasher. ●● Pull the comfort panel to open them. ●● Remove the filters one by one by pushing them towards the back side of the hood unit and simultaneously pulling downwards. ●● Any kind of bending of the filters has to be avoided when washing them.
LED LIGHT REPLACEMENT LED LIGHT LED REPLACEMENT DISMANTLE LIGHT MODULE the light modules LEDReplacing LIGHT MODULE DISMANTLEMENT You cannot replaced the light bulbs, the entire light module has to be replaced. When Replacing thechanging light module the light modules, the contacts are live. ●● You replace the light bulb but the entire light module.from the mains or switch off the Before not changing the light module(s), unplug the appliance should ●● When changing theinlight the contacts are live.
TROUBLE SHOOTING Fault Cause Solution The blade is blocked. Light is on, but motor does not work The capacitor is damaged. Replace the capacitor. The motor is damaged. Replace the motor. The internal wiring of motor is cut off/ disconnected. An unpleasant smell may Replace the motor. be produced. Apart from the above mentioned, check the following: Both light and motor do not work Oil leakage Vibration Light is damaged. Replace the light. Power cord is loose.
Maintenance schedule: To ensure the appliance continues to operate at peak performance, we recommend a routine service call every 3 years for the life of the appliance. FOR SPARE PARTS OR TO FIND THE ADDRESS OF YOUR NEAREST STATE SPARE PARTS CENTRE IN AUSTRALIA MIDEA HOME APPLIANCES AUSTRALIA PTY LTD 11/75 Lorimer Street, Docklands, Melbourne, 3008 After-sales service No.
