MAD20S1QWT MAD35S1QWT MAD50S1QWT MAD50PS1QWT MAD50PS1QGR
Owner’s Manual 1 Safety Precautions ............................................................................ 3 2 Unit Specifications and Features ................................................... 6 3 Set Up Instructions ............................................................................ 7 4 Installation Instructions .................................................................... 8 5 Operating Instructions .....................................................................
Safety Precautions SAFETY PRECAUTIONS To prevent injury to the user or personal and property damage, these instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The level of risk is shown by the following indications. WARNING This symbol indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION This symbol indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
Safety Precautions WARNING • Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prongs from the power cord. • Plug in power plug properly. Otherwise, it may cause electric shock or fire due to excess heat generation. • Always ensure effective grounding. Incorrect grounding may cause electric shock. • Unplug the unit if strange sounds, smells, or smoke come from it. A damaged product may cause fire and electric shock.
Safety Precautions CAUTION • Do not use in places where water may splash onto the unit. Water may enter the unit and degrade the insulation. It may cause an electric shock or fire. • Place the unit on a level, sturdy section of the floor. If the unit falls over, it may cause water to spill and damage belongings, or cause electrical shock or fire. • Never insert your finger or other foreign objects into grills or openings. Take special care to warn children of these dangers.
UNIT SPECIFICATIONS AND FEATURES Unit Specifications and Features Product overview Front Rear Front Panel Bucket Handle Air Intake Power Cord Storage Channel Pump Hose Outlet (some models) Garden Hose Outlet Bucket Water Level Window Relief Holes Bucket Fig. 1 Bucket Dehumidifier Lock tabs Control panel and Display Air Outlet Unit Handle Air Filter Handle (Both Sides) Power Cord Pump Inlet Hose Connection (some models) Bucket Sensor Fig.
SET UP INSTRUCTIONS Step 1: Separate dehumidifier & bucket from the nested shipping/storage position. Set Up Instructions Fig. 3a Nested Shipping & Storage Position Fig. 3b Step 2: Rotate dehumidifier 90° and align the arrows on the two labels (one on the bucket and one on the dehumidifier) and carefully sit the dehumidifier down onto the bucket. The water level window in the bucket and the user interface buttons on the dehumidifier should be on the same side when properly stacked.
INSTALLATION INSTRUCTIONS Positioning the Unit The dehumidifier should be placed in the area where dehumidification is desired most. Adjacent rooms in which dehumidification is also desired should allow adequate airflow in and out of the space containing the dehumidifier. Installation Instructions • Do not use outdoors. • This dehumidifer is intended for indoor residential applications only. This dehumidifier should not be used for commercial or industrial applications.
OPERATING INSTRUCTIONS Key Pad Features Fill Level Button and Indicators Power Button (connect) Up/Down Buttons Timer Button and Indicator Mode Button and Indicators Network Connection Indicator Bucketless Indicator LED Display Operating Instructions Fan Button and Indicators (reset filter) Pump Indicator Filter Indicator NOTICE The appearance of the control panel on your unit may vary slightly. Functions will be similar.
Set – The dehumidifier runs until the humidity setpoint has been reached. The dehumidifier will begin running once the humidity rises above the setpoint again. Max – The dehumidifier will run continuously on High Fan. Continuous – The dehumidifier will run continuously and the fan speed can be changed in this operating mode. NOTICE While operating on continuous and Max modes, the humidity setpoint cannot be adjusted manually.
Error Codes and Protection Code: Timer Function EH60 - Room temperature r sensor error--Unplug the unit and plug it back in. If error repeats, call for service. • When activating the Timer function, you are setting the time until the unit changes its power state. This means, if the unit is on, activating the timer function will set the time until the unit will turn off. If the unit is off, activating the timer function will set the time until the unit will turn on.
Removing Collected Water There are three ways to remove collected water: 1. Emptying the bucket • When the bucket reaches the set Fill Level, the unit’s display will show P2 regardless of power status. • Using proper lifting techniques, remove the unit from the bucket. Be aware, some residual water may spill from the bottom of the unit while not on the bucket. • Using two hands, grab the bucket handle and carry it to the desired drainage point.
• When removing the drain hose, some water may remain in the hose or the drain outlet. Be sure this water will not spill by drying the wet area before moving the unit. NOTICE When using the continuous draining feature, ensure the unit is placed above the sink or drain being used. This will ensure proper draining. Drain hose Fig. 9 3. Pump draining (some models) • • • Reinstall the plastic cover Max pump height: 14 ft. Make sure the hose is properly seated.
• Make sure the hose is secure so there are no leaks. • Direct the hose toward the drain, making sure that there are no kinks that will stop the water flowing. • Place the end of the hose into the drain. • Select the desired humidity setting and fan speed on the unit for pump draining to start. • When operating in Bucketless mode the pump cannot be used. NOTICE The pump operation light blinks when a failure occurs. Please turn off the unit and disconnect the power cord.
CARE AND CLEANING Turn the dehumidifier off and disconnect the plug from the power source before cleaning. 1. Clean the Grill and Case • Use water and a mild detergent. Do not use bleach or abrasives. • Do not splash water directly onto the unit. Doing so may cause an electrical shock, cause the insulation to deteriorate, or cause the unit to rust. • The air intake and outlet may get dirty during operation, use a vacuum cleaner or brush to clean. 2.
NESTING AND STORING INSTRUCTIONS Step 1: Power off and unplug the unit. Then lift the dehumidifier off the bucket. Step 2: Empty all water from bucket. WARNING Make sure the bucket is empty before nesting the dehumidifier to avoid risk of electrical shock. Fig. 13 Step 3: Make sure to press the tabs on the inside bucket feature in so that the unit can nest correctly. See Fig. 14. Step 4: Rotate dehumidifier 90° in either direction and insert into bucket to nest. Fig.
TROUBLESHOOTING TIPS Before calling for service, review this list. It may save you time and money. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Problem Solution Make sure the dehumidifiers plug is connected firmly into the wall outlet. Unit does not start Check the house fuse/circuit breaker box. Dehumidifier has reached its preset level or bucket is full. Water bucket is not in the proper position.
APP INSTRUCTIONS DECLARATION OF CONFORMITY We hereby declare that this Dehumidifier is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. SPECIFICATION OF WIRELESS MODULE Model: US-OSK103 Dimensions: 41 x 24 x 5 (mm) Standard: IEEE 802.11 b/g/n Operation Temperature: 0°C ~ 45°C / 32°F ~ 113°F. Antenna Type: External omnidirectional Antenna Operation Humidity: 10% ~ 85% Frequency: 2.
SYSTEM OVERVIEW Devices required to use the Smart Dehumidifier: 1. Smart Phone with compatible iOS or Android system. 2. Wireless Router 3. Smart Dehumidifier DOWNLOAD AND INSTALL THE APP Android QR code Apple QR code Scan to download app. • You can also go to Google Play or App Store and search for Midea Air. NOTICE All the images in this manual are for reference only, your product and app may look slightly different. The actual product and app instructions have to be considered.
CREATE YOUR ACCOUNT • Make sure your smartphone is connected to your wireless router and your wireless router has a working 2.4GHz internet connection. • It is recommended to activate your account immediately to be able to recover your password by email. 1. Press “Sign Up”. 3. Press “Registration”. 2. Enter your email address and password. App Instructions 4. If you forget your password, press “Forgot password?” on the main menu and enter your email address. Then press “Reset Password”.
ADDITIONAL APP AND SMART HOME FUNCTIONS For additional instructions regarding the features of the app and Smart Home skill capabilities, scan the QR code below.
limited Page 22
