TABLE OF CONTENTS 1. INTRODUCTION AND UNPACKING 1 2. SAFTEY INSTRUCTIONS 1-2 3. OPERATION INSTRUCTIONS 2-3 4. MOUNTING AND INSTALLATION 3-4 5. DMX-512 CONTROL CONNECTIONS 4-5 6. PHOTOMETRIC DATA 5 7. DMX CHANNELS 5-6 8. KEY FEATURES 6 9. TECHNICAL SPECIFICATIONS 7 10. MAINTENANCE AND CLEANING 8 1. INTRODUCTION AND UNPACKING Thank you for purchasing the MICROH LED SLIM P64 wash fixture. For your own safety and knowledge, please read this manual before installing or operating the device.
The device should only be used with rate voltage and frequency. Make sure that the available voltage is not higher than 120V as stated at the end of this manual. Make sure the power cord is never crimped or damaged in any way, as this could cause shock and damage. If your power chord is damaged in any way, please purchase a new cable from your local MICROH dealer. Always disconnect power, when the device is not in use or before cleaning it. Never pull out the plug by tugging the power cord.
- To keep the LED display always on press MODE & UP simultaneously. Press MODE & OFF simultaneously for the LED display to auto shut off after 20 seconds of inactivity. Use MODE button to choose the required working mode, then using UP and DOWN to adjust the relative reference data: A.Single Colour: under this mode,LED display shows “C.L.X”, “X”=0-7, press UP or DOWN button to adjust “X”.
Clamp Mounting: The MICROH LED SLIM P64 provides a unique mounting bracket assembly that integrates 2 brackets to be used to mount on a truss or the floor. When mounting this fixture to truss, be sure to secure an appropriately rated clamp to the included bracket fitted through the center hole. As an added safety measure, be sure to attach at least one properly rated safety cable to the fixture.
simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the chain. Please see illustrations below. 120Ω 2 3 1 PIN 3 PIN 2 6. PHOTOMETRIC DATA 7.
DMX mode 2: 6 channels CHANNEL CH1 CH2 CH3 CH4 CH5 CH6 VALUE 000-189 190-250 251-255 000-255 000-255 000-255 000-031 032-063 064-095 096-127 128-159 160-191 192-223 224-255 000-007 008-255 FUNCTION DIMMER (dim→bright) FLASH (slow→fast) NO FUNCTION RED (dim→bright) GREEN (dim→bright) BLUE (dim→bright) NO FUNCTION RED GREEN BLUE PURPLE YELLOW CYAN WHITE NO FUNCTION SOUND ACIVE (insensitive→sensitive) NOTE: When using Channel 6 values between 8-255, Channel 2, 3, 4 and 5 will not work.
. TECHNICAL SPECIFICATIONS MODEL: LED SLIM P64 LAMP: 181 x 10mm LEDs (Red 36, Green 85, Blue 60) OPERATING TEMPERATURE: -25°C to 45°C VOLTAGE: 120VAC 60Hz FUSE: 1A 125V GMA MAX: 30W DIMENSIONS: 8.75” x 2.5” x 11”/ 222 x 64 x 279mm PACKING DIMENSIONS: 13.5” x 12.5” x 6.75” / 343 x 318 x 171 mm NET WEIGHT: 4.85 lbs / 2.2 kg GROSS WEIGHT: 6.95 lbs / 3.
. MAINTENANCE AND CLEANING The following points have to be considered during the inspection: 1) All screws for installing the device or parts of the device must be tightly connected, and must not be corroded. 2) There must not be any deformations on the housing, colour lenses, fixations or installation spots (ceiling, suspension, trussing). 3) Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.