OWNERS MANUAL Model No. 38210 120 LB.
RULES FOR SAFE OPERATION The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may result in personal injury. Always observe the rules of safe operation. 3. Wear eye and hand protection when handling and when applying lawn or garden chemicals. 1.
SHOWN FULL SIZE A C B E D H G F I J NOT SHOWN FULL SIZE K L P O N M R Q T S KEY QTY. KEY QTY. A 2 DESCRIPTION Hex Bolt, 1/4-20 x 1-3/4" Long K 1 Flow Control Link B 6 Hex Bolt, 1/4-20 x 1-1/2" Long L 2 Spacer Tube C 8 Hex Bolt, 1/4-20 x 1" Long M 2 Hub Cap D 3 Carriage Bolt, 1/4-20 x 3/4" Long N 1 Grip E 16 Nyock Nut, 1/4-20 Thd.
ASSEMBLY INSTRUCTIONS 5. Place a wheel onto the end of the axle that has a cross hole. The long end of the hub goes to the inside. 6. Assemble a 5/32" x 2" cotter pin through the hole in the wheel hub and the axle. See figure 3. 7. Place a 5/8" flat washer onto the axle and then lightly tap a hub cap onto the axle until it is snug against the washer and wheel hub. See figure 3. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (1) Hammer (2) 7/16" Open or Boxed End Wrenches 1.
12. Assemble the leg stand tube to the bottom set of holes in the handle tube (long) using two 1/4" x 1-1/2" hex bolts and 1/4" nylock nuts. See figure 5. 13. Place a vinyl cap over the end of the leg stand tube. 15. Assemble the flow control arm to the flow control mounting bracket using a 1/4" x 1" hex bolt, two nylon washers and a 1/4" nylock nut as shown in figure 7. Tighten carefully. The flow control arm should be snug, but should pivot with no more than a slight resistance. 16.
18. Hook the free end of the flow control rod through the hole in the slide gate bracket located near the bottom of the hopper. See figure 9. HOPPER 21. Place the adjustable stop into the "ON" end of the slot in the top of the flow control mounting bracket. Secure with the 1/4" x 3/4" carriage bolt, a nylon washer, a 1/4" washer and the nylon wing nut. See figure 11.
24. Assemble the spreader shield to the front swivel brackets using two 1/4" x 3/4" carriage bolts, 1/4" washers and the two 1/4" plastic knobs. See figure 13. 25. Assemble the spreader shield to the rear swivel brackets using two 1/4" x 1" hex bolts, four 1/4" washers and two 1/4" Nylock nuts. Tighten the nuts so that the swivel bracket can still pivot freely. See figure 13. 28. Position the flow control mounting bracket (figure 15). a. Push on flow control arm until it locks in "OFF" position. b.
OPERATION APPLICATION DIAGRAM HOW TO USE YOUR SPREADER SETTING THE FLOW CONTROL (Refer to figure 15 on page 7.) 8' to 10' 1. Loosen the nylon wing nut, set the adjustable stop to the desired flow rate setting and retighten the wing nut. The higher the setting number, the wider the opening in the bottom of the hopper. 2. Refer to the application chart on page 8 and to the instructions on the fertilizer bag to select the proper flow rate setting. 3.
MAINTENANCE SERVICE AND ADJUSTMENTS CHECK FOR LOOSE FASTENERS 1. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts. REPLACING SLOTTED GEAR 1. If the axle, slotted gear and sprocket assembly is disassembled, mark down the positions of the parts as they are removed. The drive wheel and sprocket positions in relation to the slotted gear determine which direction the spreader plate will spin.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 38210 32 17 9 17 18 31 8 57 1 9 17 8 2 8 6 42 7 12 7 9 15 8 7 47 7 47 7 47 47 46 27 7 15 24 7 15 33 16 8 39 19 47 7 30 36 16 51 39 28 55 25 35 7 27 49 51 16 7 47 23 45 47 40 22 5 38 48 21 54 4 48 45 50 29 55 5 8 44 53 15 54 7 47 45 53 43 47 8 15 46 15 47 3 45 41 47 7 44 56 15 47 8 11 4 10 44 13 34 26 20 16 7 16 37 14 16 17 7 7 10 7 52 49
REPAIR PARTS LIST FOR BROADCAST SPREADER MODEL 38210 REF. PART QTY. DESCRIPTION NO. NO. AF41920 1 1 Spreader Hopper AFC-9M5732 2 2 Pop Rivet, 3/16" AF48842 3 1 Frame Tube AF24125 4 2 Shield Bracket AF741-0249 5 2 Flanged Bearing AF62482 6 1 Guide Closure Assembly 20303 7 25 Nylock Nut, 1/4" AF1543-69 8 14 Nylon Washer 20351 9 5 Washer, .312 x .734 x .
WARRANTY Meyer Products LLC warrants to Purchaser the following: Meyer Products LLC, warrants to the original purchaser for a period of one year from the date of purchase of Meyer® brand spreader products that they will be free from defects in materials or workmanship, with the exceptions stated below. No person is authorized to change this warranty or to create any additional warranty on Meyer® products. Meyer Products LLC will repair any product that proves to be defective in materials or workmanship.
