Instructions / Assembly

INSTALLATION INSTRUCTIONS FOR N7970-696-L
For Wall Mount Fixture (New. 8/20/2020)
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R .
Fig. 1
Fig. 2
Fig. 3
PREPARATION (F
ig
.1)
1. Shut off power at the fuse box or circuit breaker box. If
necessary, remove the old fixture and mounting
hardware.
2. Carefully unpack your new fixture and lay out all the
parts on a clean area. Take care not to lose any small
parts necessary for installation.
3. Attach frame (C) to the back plate (E) using the
screws (D).
4. Secure mounting plate (A) to the junction box, not
included, using screws (B) (Size: 8-32*1/2’’L). The
side of the mounting plate (A) marked “GND” must
face out.
CONNECTING THE WIRES (FIG. 2)
5. Connect the electrical wires as shown in Fig. 2,
making sure that all wire connectors are secured. If
your junction box has a ground wire (green or bare
copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly to
the mounting plate (A) using the green screw
provided. After wires are connected, tuck them
carefully inside the junction box.
FINISHING THE INSTALLATION (FIG.1)
6. Align fixture back plate (E) onto mounting plate (A)
and secure with screws (F).
7. Attach cloth shade (G) onto the back plate (E) and
secure with screws (D).
CAUTION/ATTENTION: When handling the fixture, do
not apply pressure to the LEDs. Hold the fixture by the
base only.
IMPORTANT: Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified
electrician without cutting of wire and without damage to
any decorative element to which the fixture is attached.
See installation steps for more details (Fig 3.)
a. Shut off the power.
b. Remove screws (D) and cloth shade (G) from back
plate (E).
c. Remove screws (K) and plastic gaskets (J). Carefully
separate the glass shade (L) from the back plate (E).
d. Remove screws (F) and carefully separate the fixture
from mounting plate (A).
e. Remove the wire connectors located inside the fixture
back plate to disconnect the LED module.
f. Press the button of the printed “L” quick connector on
LED module (H) with screwdriver (not included) to
disconnected the black wire and then disconnect the
white wire from the printed “N” quick connector on
LED module (H).
g. Remove plastic screws (I) on the back plate (E).
Carefully remove the LED module (H) from the back
plate (E).
h. Reverse steps b. thru g. for installing the new LED
module.
Note: The LED module should be provided by a specified
supplier.
For better heat dissipation, the LED module (H) should be
applied with thermal grease when re-lamping.
IMPORTANT:
Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall dimmer
switches.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Green or
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set#A-020-178138
-Mounting Plate
-Ground Screw
-Mounting Screw*2