Installation Guide

ManualsBrandsMetra ManualsAudioMetra Ford Transit Connect Stereo Installation Kit

METRA. The World’s best kits.

™

metraonline.com

REV. 1/6/2016 INST99-5831

CAUTION: Metra recommends disconnecting the negative battery

terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your

local Dealership for more information. All accessories, switches,

climate controls panels, and especially air bag indicator lights

must be connected before reconnecting the battery or cycling

the ignition. Also, do not remove the factory radio with the key

in the on position, or the vehicle running. It would be best to

remove the key from the ignition and then wait a few seconds

before removing the factory radio.

Installation instructions for part 99-5831

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Passenger airbag indicator

• Painted black (99-5831B) or

charcoal gray and black (99-5831G)

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) Panel clips • E) (4) #8 x 3/8” Phillips screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • XSVI-5524-NAV or AX-ADBOX2 & AX-ADFD02 Antenna Adapter: • 40-EU10

• Panel removal tool • Phillips screwdriver

• T15 Torx driver • T20 Torx driver

TOOLS REQUIRED

Ford Transit Connect 2014-up

(With factory 4.2” display)

99-5831

C D

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DIN radio provision with pocket ...................... 3

– ISO DDIN radio provision ...................................... 3

Table of Contents

NOTE: This installation kit is intended to be used in

conjunction with an AXXESS radio replacement interface.

Models with steering wheel controls will require an

AXXESS radio replacement interface and the AXXESS

ASWC-1 steering wheel control interface for all features

to work properly.

Summary of content (8 pages)

PAGE 1
Installation instructions for part 99-5831 Ford Transit Connect 2014-up Table of Contents (With factory 4.2” display) Dash Disassembly.................................................. 2 Kit Assembly –. ISO DIN radio provision with pocket....................... 3 –. ISO DDIN radio provision.......................................
PAGE 2
99-5831 Dash Disassembly 4. Remove the A/C vents and hazard switch from the panel and set aside for kit assembly. 1. Remove the top panel above the display. (Figure A) 2. Remove (2) T-15 Torx screws above the display/radio panel. (Figure B) 5. Remove (2) T-20 Torx screws from the top of the radio, and then unplug and remove from the dash cavity. (Figure D) 3. Unplug and remove the display/ radio panel. (Figure C) Continue to kit assembly.
PAGE 3
99-5831 Kit Assembly ISO DIN radio provision with pocket ISO DDIN radio provision 1. Attach the pocket to the radio brackets using the (4) #8 x 3/8” Phillips screws supplied. (Figure A) 2. Remove the metal “DIN” sleeve and trim ring from the aftermarket radio. 3. Mount the radio to the radio brackets using the screws supplied with the radio. (Figure B) 4. Snap the hazard switch into the radio trim panel from the front. (Figure A) 5. Snap the A/C vents into the radio trim panel from the back. 6.
PAGE 4
Installation instructions for part 99-5831 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-5831 Indice Ford Transit Connect 2014 y mas (con pantalla de fábrica de 4.2 pulgadas) Desmontaje del tablero................................................2 99-5831 Ensamble del kit –. Provisión de radio ISO DIN con cavidad................... 3 –. Provisión de radio ISO DDIN...................................
PAGE 6
99-5831 Desmontaje del tablero 4. Quite las rejillas de aire acondicionado y el interruptor de las luces intermitentes del panel y guárdelos para el ensamble del kit. 1. Quite el panel superior de arriba de la pantalla. (Figura A) 2. Quite los (2) tornillos Torx T-15 de arriba de la pantalla/panel del radio. (Figura B) 5. Quite (2) tornillos Torx T-20 de la parte superior del radio, desconecte y quite de la cavidad del tablero. (Figura D) 3. Desconecte y quite la pantalla/ panel del radio.
PAGE 7
99-5831 Ensamble del kit Provisión de radio ISO DIN con cavidad Provisión de radio ISO DDIN 1. Una la cavidad a los soportes del radio con los (4) tornillos Phillips #8 de 3/8” suministrados. (Figura A) 2. Quite la manga de metal “DIN” y el anillo de moldura del radio de mercado secundario. 3. Monte el radio en los soportes con los tornillos que vienen con el radio. (Figura B) 4. Coloque a presión el interruptor de las luces intermitentes en el panel de la moldura del radio desde el frente. 5.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-5831 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.