User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 95-7328 Double DIN Installation Kit for 2007 Kia Sorrento Vehicles

METRA. The World’s best kits.

™

metraonline.com

REV. 10/12/2015 INST95-7328

Installation instructions for part 95-7328

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• A) ISO DDIN trim panel • B) ISO DDIN brackets

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7302

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver

TOOLS REQUIRED

KIA Sorento 2007-09

95-7328

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-7328 KIA Sorento 2007-09 95-7328 Table of Contents Dash Disassembly.................................................. 2 Kit Assembly –. ISO DDIN radio provision....................................... 3 KIT FEATURES • ISO DDIN radio provision KIT COMPONENTS • A) ISO DDIN trim panel • B) ISO DDIN brackets REV.
PAGE 2
95-7328 Dash Disassembly 1. Unclip and remove the side trim panels. (Figure A) Note: Start at the bottom of the panels. 2. Remove (2) Phillips head screws securing the radio trim panel. Unplug and remove panel. (Figure B) 3. Remove (2) Phillips head screws securing the vent panels, then unclip and remove the (2) vent panels. (Figure C) (Figure B) (Figure A) 4. Remove (4) Phillips screws securing the radio. Unplug and remove radio.
PAGE 3
95-7328 Kit Assembly ISO DDIN radio provision 1. Snap the ISO DDIN brackets to the outside edge of the ISO DDIN trim panel. (Figure A) 2. Slide the radio into the completed assembly, and then secure it using the screws supplied with the radio. (Figure B) 3. Locate the factory wiring harness and antenna plug in the dash and make all necessary connections to the radio. Metra recommends using the proper mating adapters from Metra and/or AXXESS.
PAGE 4
Installation instructions for part 95-7328 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para la pieza 95-7328 KIA Sorento 2007-09 95-7328 Indice Desmontaje tablero................................................ 2 Ensamble del kit –. Provisión de radio ISO DDIN.................................. 3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN COMPONENTES DEL KIT • A) Panel de moldura de radio ISO DDIN • B) Soportes ISO DDIN REV.
PAGE 6
95-7328 Desmontaje tablero 1. Desenganche y quite el paneles de moldura lateral. (Figura A) Nota: Comience en la parte inferior de los paneles. 2. Quite los (4) tornillos de cabeza Phillips que sujetan el panel de la moldura del radio. Desconecte y retire el panel. (Figura B) 3. Retire (2) tornillos de cabeza Phillips que sujetan los paneles de ventilación, a continuación, soltar y quitar los paneles (2) de ventilación.. (Figura C) (Figura B) (Figura A) 4.
PAGE 7
95-7328 Ensamble del kit Provisión de radio ISO DDIN 1. Encaje los soportes ISO DDIN al el borde exterior panel de moldura de radio ISO DDIN. (Figura A) 2. Deslice la radio en el conjunto completo, y luego asegurarla con los tornillos suministrados con la radio. (Figura B) 3. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y haga todas las conexiones necesarias al radio. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS.
PAGE 8
Instrucciones de instalación para la pieza 95-7328 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.