Datasheet

ManualsBrandsMetra Manualschassis components95-5820B

INSTALLATION INSTRUCTIONS FOR PART 95-5820

95-5820

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Double DIN Radio Housing • B) Double DIN Radio Housing Brackets

• C) Radio Housing Trim Panel • D) (6) U Style Panel Clips

KIT COMPONENTS

1-800-221-0932

www.metraonline.com

APPLICATIONS

FORD

F-150 2009-up

Cutting Tool • Phillips Screwdriver • Socket Wrench • Torx Driver

Panel Removal Tool

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Harness:

• XSVI-5520-NAV Ford CAN harness 2006-up

Antenna Adapter:

• 40-CR10 - Chrysler antenna adapter 02-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-5820 APPLICATIONS FORD F-150 2009-up 95-5820 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Double DIN Radio Housing • B) Double DIN Radio Housing Brackets • C) Radio Housing Trim Panel • D) (6) U Style Panel Clips A D WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • XSVI-5520-NAV Ford CAN harness 2006-up Antenna Adapter: • 40-CR10 - Chrysler antenna adapter 02-up C B TOOLS REQUIRED: Cutting Tool • Ph
PAGE 2
95-5820 TABLE OF CONTENTS Dash Disassembly - FORD F-150 2009-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Preparation - FORD F-150 2009-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Assembly - Double DIN Radio Provision / Stacked ISO Mount Units Provision . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 *Note: Refer also to the instructions included with the aftermarket radio.
PAGE 3
95-5820 DASH DISASSEMBLY FORD F-150 2009-up 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the (1) 9/32” screw exposed. (Figure A) 3 Remove the rubber pad at the top of the radio trim panel then remove the (2) 9/32” screws exposed. (Figure B) 4 Unclip and pull the side panels containing the a/c vents away from the radio trim panel.
PAGE 4
95-5820 DASH DISASSEMBLY FORD F-150 2009-up 6 Unclip and remove the hazard/airbag switch assembly from the factory radio trim panel. (Figure E) E 7 Unclip and remove the cigarette lighter socket from the radio trim panel. (Figure F) 8 Remove (4) Torx screws securing the factory climate control to the radio trim panel. (Figure G) 9 Remove (4) 9/32” screws to remove the factory radio. F Continue to final preparation.
PAGE 5
95-5820 KIT PREPARATION FORD F-150 2009-up 1 Clip the hazard/airbag switch assembly into the radio housing in the same location as the factory radio trim panel. (Figure A) A 2 Clip the cigarette lighter socket into the radio housing in the same location as the factory radio trim panel. (Figure B) 3 Secure the climate control into the radio housing using the factory hardware in the same location as the factory radio trim panel.
PAGE 6
95-5820 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION OR STACKED ISO MOUNT UNIT(S) PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the appropriate side bracket over the mounting legs of the Double DIN trim plate aligning the holes in the trim plate and the bracket and rotate inward. Note: The notch in the housing should be on top.
PAGE 7
95-5820 FINAL ASSEMBLY FINAL ASSEMBLY FINAL ASSEMBLY A B (A) Strip wire ends back 1/2" B) Twist ends together C C) Solder D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 8
95-5820 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.