V20220704 CFN-1101 Instruction Manual Read Carefully Before Use Keep For Future Reference
TABLE OF CONTENTS Introduction ··································································································· 1 Package Contents ·························································································· 2 Safety Information··························································································· 3 Preparation ··································································································· 4 Initial Installation ······················
PACKAGE CONTENTS Fan Blades (×4) Mounting Bracket Fan Motor Assembly Light Plate MED LOW LI HI STOP 2H 4H 1H R/F Glass Shade LED Light Kit Remote Control Receiver Metal Washers (×4) Mounting Screws (×4) Wiring Nuts (×6) Blade Bolts (×14) Plastic Washers (×14) Anchor Bolts (×4) Spare Blade Arm Bolts (×2) 2 Gloves (×1) Balance Kit
SAFETY INFORMATION Warning! 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. This fan is suitable for use with solid-state speed controls. 4.
PREPARATION 1. Turn off Your Power Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed. Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Choose Your Mounting Position If you need to install a new UL listed junction box, secure it directly to your building's structure using appropriate fasteners and materials.
INITIAL INSTALLATION Wood Ceiling Concrete Ceiling Mounting Bracket Anchor Bolt Supply Wires Metal Washer Mounting Screw 1. Pass the supply wires from the junction box (not included) through the central hole of the mounting bracket. 2. Secure the bracket to the junction box with the provided fasteners. Use the mounting screws and metal washers on wood ceilings or the anchor bolts on reinforced concrete or similar ceilings.
CIRCUIT CONNECTIONS Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan. Mounting Bracket Ensure there are no loose wires or connections, and secure connectors with electrical tape. Steel Wire Receiver 1. Insert the receiver into the tray with the receiver facing the ceiling. For best performance, make sure the white antenna, on the end of the receiver, remains extended and not tangled with any of the electrical wires. Junction Box 2.
FAN MOTOR INSTALLATION Bracket Bolt Motor Bolt 1. Remove the bolts pre-installed near the top of the fan motor assembly. 2. Connect the motor assembly to the mounting bracket by sliding its slots onto the built-in bolts of the bracket. 3. Secure the motor assembly by replacing and retightening the removed bolts. FAN BLADE INSTALLATION 1. Fit a blade onto one blade arm underneath the fan motor, aligning their slots with each other. 2.
LIGHT PLATE INSTALLATION 1. Remove the bolts pre-installed underneath the fan motor assembly. 2. Feed the wire plug through the middle of the light plate. 3. Install the light plate onto the motor assembly and secure it by replacing and retightening the bolts. Wire Plug Light Plate Bolt LED LIGHT KIT INSTALLATION 1. Connect the LED light kit to the light plate using its magnetic suction-cup bolts. 2.
SHADE INSTALLATION Fit the glass shade onto the light plate and screw it into place. Ensure it is firmly connected to avoid loosening during use. Light Plate Glass Shade COLOR TEMPERATURE ADJUSTMENT The LED light has 3 different color setting: Warm White (3000K), Daylight (4500K), and Cool White (6000K). To adjust the light settings, 1. Press LIGHT on the remote control to turn on the LED light. 2. Press LIGHT again to turn off the light. 3.
REMOTE CONTROL OPERATION Install the remote control holder onto any wall or suitable flat surface using the two steel screws.
TROUBLESHOOTING Potential Problems Common Solutions Check fuses and/or circuit breakers and reset if needed. Cut off power to the fan and check its internal electrical connections. Fan blades don't rotate Replace the remote control’s batteries. Check that the fan cover is correctly placed and no fasteners interfere with the movement of the blades. Contact customer service to replace a faulty remote control. Check that all fasteners are well tightened.
