V20210602 CFN-1052 Instruction Manual Read Completely Before Installation & Use and Keep for Future Reference
TABLE OF CONTENTS Introduction ·························································································· 1 Package Contents ················································································· 2 Safety Information·················································································· 3 Preparation ·························································································· 4 Initial Installation ··························································
PACKAGE CONTENTS B F C A G D H E A. Fan Blades (3) B. Ceiling Mounting Bracket C. Canopy D. Downrod E. Coupling Cover F. Remote Control I G. Remote Receiver H. Mounting Screws (4) Flat Washers (4) Star Washers (4) J Wire Nuts (8) Bolts (2) Spare Bolt K Balance Kit I. Fan Motor Assembly J. Light Plate K. LED Light Kit L L.
SAFETY INFORMATION Warning! 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. This fan is suitable for use with solid-state speed controls. 4.
PREPARATION 1. Turn Off Your Power Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed. Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Choose Your Mounting Position If you need to install a new UL listed junction box, secure it directly to your building's structure usingappropriate fasteners and materials.
INITIAL INSTALLATION Junction Box Washers Ceiling Mounting Bracket Hook Mounting Screws 120V Wires Loosen the 4 screws on the mounting bracket. Use the screws and washers to attach it to your ceiling. DOWNROD MOUNTING Downrod Step 1: Remove the pin and clip from the downrod. Then partially loosen the two steel screws in the yoke at the top of the motor assembly. Canopy Canopy Cover Canopy Cover Set Bolt Step 2: Carefully place the canopy, canopy cover, and coupling cover onto the downrod.
CIRCUIT CONNECTIONS Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan. Ensure there are no loose wires or connections, and secure connectors with electrical tape. Downrod Step 1: Connect the 5 colored wires from the remote receiver to the 5 identically colored lead wires from the fan motor. Secure each set with the provided wire nuts.
CANOPY INSTALLATION Outlet Box Ceiling Mounting Bracket Screw Screw Canopy Step 1. Tuck all the connections neatly into the ceiling outlet box. Step 2. Slide the canopy up to the mounting bracket and place one of the key hole slots over the mounting bolt on the mounting bracket. FAN BLADE INSTALLATION Loosen the bolts & washers pre-installed on blade holder. Insert the blade through the blade slot in the motor housing.
LIGHT PLATE & SHADE INSTALLATION Feed the wire connector through the middle of the light plate. Install the light plate on the motor assembly with the provided bolts. Light Plate Wire LED Light Kit Bolt Magnetic Bolts Connect the LED light kit to the wire connector. Attach the LED light kit to the light plate using its magnetic bolts. Install the glass lamp shade onto the light plate, turning it into place. Ensure it is firmly connected to avoid loosening during use.
REMOTE CONTROL OPERATION Install the remote control holder onto any wall or suitable flat surface using the two steel screws. Upon first use, connect the remote control to its receiver in the fan by pressing LI and HI on the emitter until a beep is heard. (Note that this programming cannot be done for the first 30 seconds after the receiver is turned on.
TROUBLESHOOTING Potential Problems Common Solutions Check fuses and/or circuit breakers and reset if needed. Cut off power to the fan and check its internal electrical connections. Fan blades don't rotate Replace the remote control’s batteries. Check that the fan cover is correctly placed and no screws interfere with the movement of the blades. Contact customer service to replace a faulty remote control. Check that all screws and fasteners are well tightened.
