READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Table of Contents: Installation Guide Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Mounting Plate Installation. pg. 4 Preparation for Wiring. pg. 5 Wiring. pgs. 5 - 6 Fan Assembly. pg. 6 Blade Assembly. pg. 7 Light Kit Assembly (Optional). pgs. 7 - 8 Assembly of Handheld Remote Control. pg. 9 Automated Learning Process./ Activating Code. pg. 10 Remote Control Operation. pg. 10 Testing Your Fan. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b c d e f g a. mounting plate. 1 piece b. housing ring. 1 piece c. motor housing. 1 piece d. wall plate.1 piece e. remote control cover.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7ft. (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 225 square feet (20.9 square meters). 12 ft. - 15 ft. (3.66m - 4.57m) blade edge 30 inches 7 feet (76cm) (2.13m) 12 ft. - 15 ft. (3.66m - 4.
. Preparation for Wiring. wood joist With wider opening facing up, place housing ring over top of motor housing. Then, push housing ring down past top edge of motor housing. Lift motor housing to mounting plate and then hang motor housing on j-hook on underside of mounting plate. (Use one of the non-slotted holes on the rim of the motor housing to do so.) This will allow motor housing to hang out of the way while wiring.
. Wiring. (cont.) Modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. [PLEASE NOTE: Wall and/or handheld remote control must be used for fan to operate. If you do not wish to use the wall control, please proceed to Section 7 to continue with fan installation.] *NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
8. Blade Assembly. WARNING: To reduce the risk of serious bodily injury, DO NOT use power tools to assemble the blades. If screws are overtightened, blades may crack and break. motor housing Time Saver: Washers for blade attachment screws can be set on each screw prior to installing blades. blade Locate 15 blade attachment screws and washers in hardware pack.
9. Light Kit Assembly (Optional). (cont.) Remove 1 screw from post on underside of fitter plate and partially loosen the other 2 screws. motor housing Connect WHITE wire from motor housing to WHITE wire from LED light kit. Connect BLACK (or BLUE) wire from motor housing to BLACK wire from LED light kit. Be sure molex connections snap together securely. [Refer to diagram 2.] CAUTION: If you will NOT be using the light kit, do NOT connnect the molex connections.
10. Assembly of Handheld Remote Control. IN ORDER TO USE THE HANDHELD REMOTE CONTROL, PLEASE CONTINUE WITH SECTION 10 for remote control assembly instructions. If you have already installed the wall control but do not wish to use the handheld remote control, please proceed to Section 11. remote control cover Gently pull on remote control cover to separate top and bottom parts. [Refer to diagram 1.
11. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LIFETIME LIMITED WARRANTY: We warrant this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: We will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact Customer Service to arrange for return of fan. Return fan, shipping prepaid, to us.