MES1B (343) 5/9/03 4:12 PM Page 1 READ AND SAVE THESE INSTRUCTIONS USE AND CARE GUIDE FOR MODEL MES1B, MES1W, MES1R Java-Pod™ Coffee Maker
MES1B (343) 5/9/03 4:12 PM Page 2 IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: • Read all instructions. • Do not touch hot surfaces. Use handles or knobs. • To protect against fire, electric shock, do not place cord, plugs, or appliance in water or other liquid. • Close supervision is necessary when any appliance is used by or near children. • Unplug from outlet when not in use and before cleaning.
MES1B (343) 5/9/03 4:12 PM Page 3 ADDITIONAL IMPORTANT SAFEGUARDS WARNING: This appliance generates heat and escaping steam during use. Use proper precautions to prevent the risk of burns, fires, or other injury to persons or damage to property. • All users of this appliance must read and understand this Owner’s Manual before operating or cleaning this appliance. • The cord to this appliance should be plugged into a 120V AC electrical outlet only.
MES1B (343) 5/9/03 4:12 PM Page 4 POLARIZED PLUG: This appliance has a polarized plug, (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
MES1B (343) 5/9/03 4:12 PM Page 5 Your product may vary slightly from illustration. Parts Identification Java-Pod (Samples included in box. To order, see page 14.
MES1B (343) 5/9/03 4:12 PM Page 6 Before Using Your One:One™ Java-Pod™ Coffee Maker Become familiar with all parts of the appliance. Keep your coffee maker clean Clean and descale coffee maker on a regular basis. See “Cleaning and Descaling”, pages 11-12. We recommend cleaning the Water Tank and the Drip Spout as well as the Java-Pod Holder, before using your coffee system for the first time. Turn on the coffee maker for a full cycle using water only.
MES1B (343) 5/9/03 4:12 PM Page 7 2. Fill the Water Tank with fresh water up to the ‘Max’ line, and fit back into the Base (down and in) until it “snaps” into place, see Figure 4. FIGURE 4 3. Lift Lid by pulling out on the Lever. Top will pop up. Push back so Lid is in fully raised position, see Figure 5.
MES1B (343) 5/9/03 4:12 PM Page 8 4. Place the empty Java-Pod Holder inside the coffee maker, see Figure 6. FIGURE 6 5. To close the Lid, press down firmly on the top of the Lid and hold in place while pushing the Lever back so it is flush with the Lid and locks into place, see Figure 7. FIGURE 7 6. Place a large measuring cup or bowl (must hold at least 27 ounces) below the coffee Drip Spout to collect the water.
MES1B (343) 5/9/03 4:12 PM Page 9 7. Press the Power Light/Indicator Button to turn power on, then simultaneously press the 5-Ounce Cup and 8-Ounce Cup Buttons, see Figure 8. FIGURE 8 The water from the Water Tank will cycle through the coffee maker. Note: If Water Tank becomes dry for 3 or more days, please repeat above process (steps 1-7). CAUTION: Do not immerse cord, plug or coffee maker in water or other liquid.
MES1B (343) 5/9/03 4:12 PM Page 10 4. Place one Melitta® java-pod™ inside the Java-Pod Holder. Press lightly on the java-pod™ to make sure it sits evenly in the JavaPod Holder. CAUTION: Use only specially designed Melitta® java-pods™ in your One:One™ Java-Pod™ Coffee Maker. The use of loose ground coffee or pods not designed for this coffee maker may result in poor coffee or cause damage to the coffee maker. CAUTION: Never use torn java-pods™ as this could clog the machine and damage it.
MES1B (343) 5/9/03 4:12 PM Page 11 Helpful Hints for Brewing Fresh Water Use fresh water daily. If you haven’t used your coffee maker for a few days, rinse the Water Tank, fill it with fresh water and turn on the appliance for a full cycle, with water only before using a java-pod™ again. Note: If Water Tank becomes dry for 3 or more days, see section “Before Using Your One:One™ Java-Pod ™ Coffee Maker,” steps 1-7. Java-pods™ Remove the java-pods™ after use.
MES1B (343) 5/9/03 4:12 PM Page 12 4. Remove the Drip Tray and Overflow Tray, see Figure 10. FIGURE 10 5. Clean the Java-Pod Holder, Pod Chamber, Drip Spout, Drip Tray and Overflow Tray with hot water. If necessary, use a little dish soap or wash them in the dishwasher (top shelf only). Note: The Java-Pod Holder, the Drip Tray, Overflow Tray and the coffee Drip Spout may be washed in the dishwasher. Clean the Water Tank with hot water. Use soapy water if necessary.
MES1B (343) 5/9/03 4:12 PM Page 13 Troubleshooting Should a problem occur, you may be able to find an answer in the text below. If the text proves unhelpful or if you require further information, please contact Consumer Service. 1. The coffee is too weak. Check the following: • the java-pod™ is placed properly in the Java-Pod Holder. You may need to lightly press it down into the holder. • you have selected the correct button according to the number of ounces and strength desired.
MES1B (343) 5/9/03 4:12 PM Page 14 6. The indicator light keeps flashing at rapid intervals. Check the following: • the Water Tank must be inserted properly inside the appliance. • there must be enough water in the Water Tank. Fill the Water Tank to the “Max” fill line. • the coffee maker may require cleaning. See “Before Using Your One:One™ Java-Pod™ Coffee Maker”, pages 6-8. • room temperature must be above 40°F. 7. The Lid cannot be opened. Turn coffee maker off. Unplug unit.
MES1B (343) 5/9/03 4:12 PM Page 15 IMPORTANT NOTICE If any parts are missing or defective, DO NOT return this product. Please call our Customer Service Department for assistance. 800-841-1628 Monday - Friday 9:00 am - 5:00 pm CST Thank You LIMITED ONE YEAR WARRANTY Warranty: This Melitta® product is warranted by Salton, Inc. to be free from defects in materials or workmanship for a period of (1) year from the original purchase date.
MES1B (343) 5/9/03 4:12 PM Page 16 Out-of-Warranty Service: A flat rate charge by model is made for out-of-warranty service. Include $12.00 (U.S.) for return shipping and handling. We will notify you by mail of the amount of the charge for service and require you to pay in advance for the repair or replacement. For products purchased in the USA, but used in Canada: You may return the product insured, packaged with sufficient protection, and postage and insurance prepaid to the USA address listed below.
