Check that the unit has not been damaged during transport Protection Against Fire 1. 3. 4. 5. 6. Maintain a minimum of 1 foot distance from any type of flame. Replace fuse only with the specified type and rating. Do Not install the unit to close to a heat source. Make sure cable are properly secured away from unit movement. Maximum surface operating temperature 90º. Protection Against Fire 1. 2. 3. 4. Disconnect power before lamp replacement or servicing.
Specifications Part Numbers Fixture Lamp Flight Case 1030 - AXIS 250 LNSK250/2 9051-Dual Flight Case Mechanical Specifications Pan: 530° 16.75 ” Tilt: 280° DMX Connectors: 3-pin XLR connectors Reflector: Glass reflector with cold mirror coating Thermal: Maximum ambient temperature 40° C Maximum surface temperature 80° C Fastening System: 2 clamp placement attachments Fixture 8” 3” 15.25 17.5 ” Packaged for Shipping Size: 16.75”L x 16”W x 20.5”H Size: 20”L x 19.25”W x 22.
Color 1: Open 2: Red 3: Yellow 4: Purple 5: Light Green 6: Orange 7: Blue 8: Magenta 9: Dark Blue 10: Light Blue Gobo 1: Open 2: Magenta Swirl 3: Daisy 4: Swivel 5: Stars 6: Diffusion 7: Circular Stars Dichroic Glass Gobo: Diameter 27 mm Image 24 mm Thickness 4 mm max DMX Channels Channel Function Channel Function Channel Function 1 Pan 2 Tilt 7 Color Wheel 13 Prism Rotation 8 Gobo Wheel 14 Focus 3 Pan Fine 9 Gobo Rotation 4 Tilt Fine 10 Shutter 5 Pan/Tilt Speed 11 Dimmer
Main Power Connection Caution! 1. 2. 3. Do not connect fixture to a dimmer system. This unit must be earthed. (electronically grounded) Replace fuse only with the specified type and rating. 110V 50/60hz Connection The occupation of the connection-cable is as follows: Cable (USA) Cable (EU) Pin International Brown Brown Live L Blue Blue Neutral N Yellow / Green Yellow/Green Pin DMX-512 Connection The fixture is equipped with 3 pin XLR Sockets for DMX input and output.
Lamp Replacement Caution! 1. Disconnect power before you begging. 2. Allow 15min for the unit and lamp to cool. 3. Do not touch lamps glass envelope with your fingers. If this happens clean with alcohol / to remove oils. Lamp Placement To insert the lamp MSD 250/2, HSD250. Use a Phillips screwdriver to unscrew the bolts that hold the plastic Bessel in place there will be 3 screws. Unscrew the knurled-head screws of the lamp holder and remove it. Carefully insert the lamp into the lamp holder.
Axis 250 DMX Profile DMX Channel 1 2 3 4 Function Pan Tilt Pan Fine Tilt Fine Description Pan Tilt Pan Fine Tilt Fine Pan/Tilt Speed (From fast to slow) 5 Speed 6 Reset 7 Color 8 Gobo Wheel 9 Gobo Rotation 10 Shutter 11 Dimmer 12 Prism 13 Prism Rotation 14 Focus Max Speed Blackout During Movement Reset Open Red Yellow Purple Light Green Orange Blue Magenta Dark Blue Light Blue Forward Color Scroll (slow to fast) Backwards Color Scroll (fast to slow) Open Magenta Swirl Daisy Swivel Sta
Main Control Menu The control board on the fixture base is your interface to access and control all the functions on the unit. Its digital display gives you a code view of the options and functions. The following will explain each function and its options. DMX MODE Reverse Pan Reverse Tilt Demo Mode ENTER Color Control DOWN UP DOWN DMX Address ENTER UP MODE Reset 0-512 DMX Address Use the up/down keys to select the required DMX start channel.
Cleaning and maintenance Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years. The following points have to be considered during the inspection: 1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded. 2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
Mega-Lite 5718 Kenwick St San Antonio, TX 78238 Ph 210-684-2600 Fax 210-855-6279 www.mega-lite.com / info@mega-lite.
