Installation guide

ManualsBrandsMaytag ManualsKitchen AppliancesMMC5080AAS

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Before attempting the installation of this kit, be sure to unplug the oven from wall receptacle.

Your oven is designed to be installed under properly constructed, good condition wood or metal cabinets that are sturdy enoughto support

the items you have in the cabinet, plus an additional 41 kg (90 pounds) from the cabinet bottom.

Empty the contents of your selected cabinet and the delicate items in adjoining cabinets.

(NOTE: When drilling the holes, the vibration could cause damage to fragile items such as crystal or china.)

Now, you must inspect your cabinets. If any of the following conditions exist, then it is your personal responsibilityto test the cabinets or

contact a qualified cabinet maker.

1. Separation of joints between the bottom shelf and the cabinet structure.

2. Splitting, cracking or other signs of deterioration.

3. Check the number of screws used to install your cabinets. If your cabinet is attached to the wall with only two screws at the top, then

you must add two screws at the bottom to firmly secure your cabinet to the wall. When addingthe screws, be sure that they enter wall

studs with at least 1.3 cm (1/2") penetration.

4. On wood cabinets, the bottom shelf must be at least .48 cm (3/16") thick masoniteor plywood.

5. Be sure that the underside of the cabinet is at least 50 cm (20") wide and 35.0cm (13 25/32") deep. If the cabinet is less than

35.0cm(13 25/32") deep, follow the cabinet mounting instructions catefully if you desire to mount your oven under cabinet.

To test your cabinets, place a 40 KG(90LB.)load, plus the equivalent weight of items normally stored on the shelf*,for a minimum of five

minutes.

*You may consider using jugs of water, bricks or books to obtain the test load.

PLEASE NOTE: Ifyour cabinet is properly constructed and suitably installed it will withstand this test without any damage; however, there

is the possibility of damage should the cabinet be incapable of supporting the additional load.

The Maytag Company is NOT RESPONSIBLE FOR ANY DAMAGE OR OTHER CONSEQUENCES resultingfrom the performance of

this test.

Ifyou are unsure that your cabinets are suitable for this type of installation you may use the oven on your countertop.

TOOLS AND PARTS

The following tools are needed for installation of your unit:

Drill and .64cm (1/4") drill bit

Phillips and flat blade screwdrivers

Nail or center punch

Pencil and ruler

Scissors

Hammer

INSTALLATION PARTS LIST

The following is a list of the parts that you may need for installation of your oven.

Remove all partsfrom the cooking cavity and compare them with the parts list and illustration to be sure that none are missing. Use this

time to become familiar with each piece.

Part No.: 8101 P611-60

Code No.: DE68-02900A

Summary of content (4 pages)

PAGE 1
IMPORTANT SAFETY INSTRUCTIONS WARNING Before attempting the installation of this kit, be sure to unplug the oven from wall receptacle. Your oven is designed to be installed under properly constructed, good condition wood or metal cabinets that are sturdy enough to support the items you have in the cabinet, plus an additional 41 kg (90 pounds) from the cabinet bottom. Empty the contents of your selected cabinet and the delicate items in adjoining cabinets.
PAGE 2
PARTS LIST 1.3 Sets of bolts 2.4-washers-A 3.4-washers-B 4.1-Template Upon completing your check of the parts list, read all instructions completely before starting the installation. This will help you to become familiar with the process and make installation easier. (NOTE: It is suggested that you gather all needed tools and installation parts in one location.) Q PREPARATIONS Open the template and detach both segments along the dashed line with scissors. You should have two separate pieces.
PAGE 3
DRILLING APPROACH You have two options for drilling the mounting holes for your oven. First, you can drill from inside of the cabinet if you have adequate space and your shelves are removable. Second, you can drill from the bottom. If possible, it is generally easier to work from the inside of the cabinet. Use the instructions applicable to the approach you select. Make sure you use the template properly depending whether you drill holes from the inside or bottom side of the cabinet.
PAGE 4
• • Position remaining piece of Template 2 under the cabinet and align the hole center lines with arrows on Template 1 so that the distance from right hole center to left hole center measures the distance indicated on the templates. (You may have to cut excess paper from middle of the template to make it lay flat.) Position Template 2. (The cut line along the front edge of template must be placed against the back of the front rail.