Model # 261-3389
Table of Contents Maintenance ............................................... 8 Parts List and Diagram .............................. 10 Warranty .................................................... 12 SaFETY Safety ......................................................... 2 Specifications ............................................. 3 Assembly .................................................... 4 Operation ....................................................
18. Keep children and bystanders away while operating the Crane. Distractions can cause you to lose control. 13. Do not use for aircraft purposes. 19. have Crane serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the Crane is maintained. 15. Before driving vehicle, retract Winch Cable completely, lower boom and position over truck’s wheel well, then insert Post Pin to prevent boom from swiveling. 16. Stay alert.
assembly Instructions Read EnTIRE IMpORTanT SaFETY InFORMaTIOn section at beginning of this manual including all text under subheadings therein before setup or use of this product. SaFETY note: Remove Post (2) and Boom (3) before mounting Base. 4. Slide Post (2) onto Base and secure using Post Pin (14) and R-Pin (10). (See Figure B.) 1. Locate a mounting position so the Crane will be near end of truck bed and can be attached to frame.
note: You may need to pull out cable from Winch reel to expose bolt holes on Winch base. 7. Connect Boom Bracket to Ram using Pin (12) and R-Pin (10). (See Figure D.) 9. Attach Winch (5) to Boom with Bolts (7), and Lock Washers (8). pin (13) upper post Bracket 10. Thread Grease Fitting (21) into Post. (See Figure F.) R-pin (10) Boom (3) Bolt (7) R-pin (10) lock Washer (8) Winch (5) SaFETY 6. Attach Boom (3), Bracket facing down, to Upper Post Bracket using Pin (13) and R-Pin (10).
Operating Instructions Read EnTIRE IMpORTanT SaFETY InFORMaTIOn section at beginning of this manual including all text under subheadings therein before setup or use of this product. SaFETY note: Once assembly is complete, tighten all Bolts before initial operation. Bleeding Instructions 4. Check fluid level and, if necessary, top off with hydraulic fluid. IMpORTanT! Before first use, check for proper hydraulic fluid level and thoroughly test the Crane.
WaRnInG! Engage parking brake before use. Do not move vehicle with load attached to Crane. 6. Before lifting load, make sure Cable is not kinked or twisted. 1. Remove Post Pin and swivel Boom so Hook is over load. If necessary, remove Boom Pin, adjust Boom Extension, then replace Boom Pin. WaRnInG! Do not lift load with Winch. Winch is for adjusting slack only. lift load with hydraulic Ram only. WaRnInG! Do not attempt to extend or retract Boom while load is attached. 7. To lift load: Capacity (lb.
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. SaFETY TO pREVEnT SERIOuS InJuRY FROM aCCIDEnTal OpERaTIOn: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and lubrication 1. BEFORE EaCh uSE, inspect the general condition of the tool.
TO pREVEnT SERIOuS InJuRY: use caution when troubleshooting malfunctioning Crane. Stay clear of supported load. Completely resolve all problems before use. If solutions presented in Troubleshooting guide do not solve the problem, have a qualified technician inspect and repair Crane before use. after Crane is repaired: Test it carefully without a load by raising and lowering it fully, checking for proper operation, BEFORE RETuRnInG CRanE TO OpERaTIOn.
parts list and Diagram plEaSE REaD ThE FOllOWInG CaREFullY SaFETY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
MaInTEnanCE OpERaTIOn SETup SaFETY assembly Diagram Page 11