Datasheet

Detailed Description
The MAX7032 300MHz to 450MHz CMOS transceiver
and a few external components provide a complete
transmit and receive chain from the antenna to the digi-
tal data interface. This device is designed for transmit-
ting and receiving ASK and FSK data. All transmit
frequencies are generated by a fractional-N-based syn-
thesizer, allowing for very fine frequency steps in incre-
ments of f
XTAL
/4096. The receive LO is generated by a
traditional integer-N-based synthesizer. Depending on
component selection, data rates as high as 33kbps
(Manchester encoded) or 66kbps (NRZ encoded) can
be achieved.
Receiver
Low-Noise Amplifier (LNA)
The LNA is a cascode amplifier with off-chip inductive
degeneration that achieves approximately 30dB of volt-
age gain that is dependent on both the antenna match-
ing network at the LNA input and the LC tank network
between the LNA output and the mixer inputs.
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to GND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible match for low-input
impedance such as a PCB trace antenna. A nominal
value for this inductor with a 50Ω input impedance is
12nH at 315MHz and 10nH at 434MHz, but the induc-
tance is affected by PCB trace length. LNASRC can be
shorted to ground to increase sensitivity by approxi-
mately 1dB, but the input match must then be reopti-
mized.
The LC tank filter connected to LNAOUT consists of L5
and C9 (see the Typical Application Circuit ). Select L5
and C9 to resonate at the desired RF input frequency.
The resonant frequency is given by:
where L
TOTAL
= L5 + L
PARASITICS
and C
TOTAL
= C9 +
C
PARASITICS
.
L
PARASITICS
and C
PARASITICS
include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, LNA output impedance, etc. These
parasitics at high frequencies cannot be ignored and
can have a dramatic effect on the tank filter center fre-
quency. Lab experimentation must be done to optimize
the center frequency of the tank. The total parasitic
capacitance is generally between 5pF and 7pF.
Automatic Gain Control (AGC)
When the AGC is enabled, it monitors the RSSI output.
When the RSSI output reaches 1.28V, which corre-
sponds to an RF input level of approximately -55dBm,
the AGC switches on the LNA gain-reduction attenua-
tor. The attenuator reduces the LNA gain by 36dB,
thereby reducing the RSSI output by about 540mV to
740mV. The LNA resumes high-gain mode when the
RSSI output level drops back below 680mV (approxi-
mately -59dBm at the RF input) for a programmable
interval called the AGC dwell time. The AGC has a hys-
teresis of approximately 4dB. With the AGC function,
the RSSI dynamic range is increased, allowing the
MAX7032 to reliably produce an ASK output for RF
input levels up to 0dBm with a modulation depth of
18dB. AGC is not required and can be disabled in
either ASK or FSK mode. AGC is not necessary for FSK
mode because large received signal levels do not
affect FSK performance.
f
LC
TOTAL TOTAL
=
×
1
2π
MAX7032
Low-Cost, Crystal-Based, Programmable,
ASK/FSK Transceiver with Fractional-N PLL
______________________________________________________________________________________ 13
Pin Description (continued)
PIN NAME FUNCTION
27 HVIN
High-Voltage Supply Input. For 3V operation, connect HVIN to PAVDD, AVDD, and DVDD. For 5V
operation, connect only HVIN to 5V. Bypass HVIN to GND with 0.01µF and 220pF capacitors placed
as close as possible to the pin.
28 CS Serial Interface Active-Low Chip Select
29 DIO Serial Interface Serial Data Input/Output
30 SCLK Serial Interface Clock Input
31 XTAL1 Crystal Input 1. Bypass to GND if XTAL2 is driven by an AC-coupled external reference.
32 XTAL2 Crystal Input 2. XTAL2 can be driven from an AC-coupled external reference.
— EP Exposed Pad. Solder evenly to the board’s ground plane for proper operation.